Memorandum presenting some effects of aileron deflection on the static lateral and directional aerodynamic characteristics of four airplane models which are representative of aircraft capable of flight at supersonic speeds. The results are presented for subsonic Mach numbers ranging from 0.60 to 0.90 and for supersonic Mach numbers ranging from 1.20 to 1.90. They are limited to the most pertinent aerodynamic effects of ailerons contributing to the lateral and directional characteristics of each airplane type.

Memorandum presenting an investigation of the steady-state wing loads conducted on a Boeing B-52 airplane over a range of Mach numbers and altitudes. Results regarding flight tests and air-load calculations are provided.

Report discussing available wind-tunnel data on low-speed horizontal-tail contribution to the static longitudinal stability of high-speed airplane configurations with unswept and sweptback wings. The effects of variations of tail position, wing plan form, airfoil section, trailing-edge flaps, stall-control devices, and ground interference on air-flow characteristics an tail contribution are also described.

Memorandum presenting an investigation to determine the drag, static longitudinal and lateral stability, and longitudinal trim characteristics of an airplane configuration with tail surfaces outboard of the wing tips. Included in the basic data are some effects of Reynolds number, engine pack, and wing twist combined with toe-out of the vertical tails.

Memorandum presenting a low-speed investigation in the free-flight tunnel to determine the effect of small canard surfaces on the directional stability of a fighter-airplane model with an aspect ratio of 3.4 and a 42 degree sweptback wing. The canard surfaces were found to be generally ineffective at angles of attack below 20 degrees.

Report presenting static tests on the compatibility of gaseous fluorine with various liquids, solid plastics, waxes, and greases at pressures of 0 and 1500 pounds per square inch gage and atmospheric temperature. Several materials were found to be compatible at atmospheric pressure, but only Teflon and ruby were compatible under static conditions at 1500 pounds per square inch gage.

Memorandum presenting the results of an investigation of the stability, control, and induced rolling moments of a canard missile with cruciform wings of rectangular plan form at Mach number 1.7. All data including the measured hinge moments of the canard control surfaces, the axial forces on the complete missile, and the forces and moments on the various combinations of the missile components are presented in tabular form.

Report presenting an investigation of the aerodynamic characteristics of various configurations of the Republic F-105 at Mach numbers from 0.60 to 1.13. The primary focus of this report are the static lateral and directional stability and control characteristics of the model. Results regarding force and moment results, longitudinal characteristics, lateral and directional characteristics.

Memorandum presenting an airborne missile simulator used to represent visually the predicted flight behavior of the Navy XASM-N-7 Bullpup air-to-surface missile, which is guided along the line of sight to the target by bang-bang radio signals controlled by the pilot of the launch airplane. Quantitative response measurements showed that the simulator gave a good representation of the trajectory and control characteristics predicted for the Bullpup missile, and the simulation appeared plausible to the pilots.

Memorandum presenting the effect of blunting on the internal performance of a two-cone inlet with an internally cylindrical cowl investigated experimentally at Mach number 4.95. Total-pressure-recovery and mass-flow data were obtained for a range of spike and cowl bluntness.

Report presenting an investigation of the effect of inlet component blunting on performance using an axisymmetric external-compression inlet in the supersonic wind tunnel. The investigation was carried out to determine the performance penalties associated with spike-tip and cowl-lip blunting. Results regarding the effect of rounding the spike tip on inlet performance, overall drag coefficients, flow distortion, and Schileren photographs are provided.

Memorandum presenting a two-dimensional wind-tunnel investigation to determine the extent to which boundary-layer removal through slots is effective as a means for maintaining extensive laminar layers at high Reynolds numbers. Results regarding drag, suction-flow and pressure-loss distribution, surface pressure distribution, lift, and difficulties encountered in obtaining extensive laminar flow are provided.

"An investigation of the isothermal wake-flow characteristics of several flame-holder shapes was carried out in a 4- by 4-inch flow chamber. The effects of flame-holder-shape changes on the characteristics of the Karman vortices and thus on the recirculation zones to which experimenters have related the combustion process were obtained for several flame holders. The results may furnish a basis of correlation, of combustion efficiency and stability for similarly shaped flame holders in combustion studies" (p. 1).

Report discussing tests of a model of the Chance Vought Regulus II missile to determine the lift, static stability, dynamic stability, trim, duct information, and drag for a range of Mach numbers.

Control trailing-edge thickness and aspect ratio effect on oscillating hinge-moment and flutter characteristics of flap-type controls. Results regarding damping moments and flutter characteristics and spring moments are provided.

"A rocket of the 1000-pound-thrust class using liquid oxygen and JP-4 fuel as propellant was installed in the Lewis 8- by 6-foot tunnel to permit a controlled study of some of the factors affecting the heating of a rocket-missile base. Temperatures measured in the base region are presented from findings of three motor extension lengths relative to the base. Data are also presented for two combustion efficiency levels in the rocket motor" (p. 1).

Report presenting a summary of NACA research on afterburners for turbojet engines during the past 5 years. The references present over 1000 afterburner configurations and about 3500 hours of operation. The report covers the following topics: burner-inlet diffusers, fuel-injection systems, flameholders, combustion space, combustion instability, starting and transient performance, effects of diluents, and burner-shell cooling.

"Investigation of the control parameters of an external-internal compression inlet indicates that the cowl-lip shock provides a signal to position the spike and to start the inlet over a Mach number range from 2.1 to 3.0. Use of a single fixed probe position to control the spike over the range of conditions resulted in a 3.7-count loss in total-pressure recovery at Mach 3.0 and 0 deg angle of attack. Three separate shock-sensing-probe positions were required to set the spike for peak recovery from Mach 2.1 to 3.0 and angles of attack from 0 deg to 6 deg" (p. 1).

"Results are presented for the loads and moments acting on the individual tail surfaces of a body-tail combination over a wide range of angles of attack and sideslip. The effects of forebody length and panel-panel interference on the characteristics are included. It is shown that large nonlinear variations in these loads and moments, which occur at some combinations of angle of attack and sideslip, cannot be predicted by low-angle theory" (p. 1).

Report discussing testing on the drag, longitudinal stability, and lateral stability characteristics of a model of the McDonnell F4H-1 airplane. The minimum drag coefficients, neutral point, horizontal-tail-incidence range, static directional stability, and effective dihedrals are presented.

From Summary: "A method for computing the effect of surface roughness on the drag coefficient of an airplane is presented. Calculated results using this method are compared with experimental results from both flight and wind-tunnel tests. In general, the agreement is believed satisfactory."

Report presenting a method for calculating the drag, in a real compressible fluid and at subcritical Mach numbers, of airfoil sections at arbitrary life coefficients and of bodies of revolution at zero angle of attack. The values of drag coefficient are compared with values obtained for the same configurations by other methods. The differences between the results are found to lie withint he limits of accuracy of current experimental techniques.

An altitude-test-chamber investigation of a 28-inch-diameter ram-jet engine at a simulated flight Mach number of approximately 2.0 for altitudes of 40,000 to 50,000 feet was conducted at the NACA Lewis laboratory. Three different flame holders, varying in the number and size of the annular gutters, in conjunction with several fuel-injection systems were investigated. The combustion efficiency for the flame-holder fuel-injection system that provided the best over-all operational fuel-air-ratio range (0.03 to 0.075) was over 0.9 at a fuel-air ratio of about 0.065 for the altitude range investigated.

A heat-transfer investigation was conducted with air flowing through an electrically heated Inconel tube having either a long-approach or a right-angle-edge entrance, an inside diameter of 0.402 inch, and a length of 24 inches over a range of Reynolds numbers up to 375,000 and average inside-tube-wall temperatures up to 2000 degrees R. Good correlation of heat-transfer data was obtained for both entrances, which substantiates work previously reported. A fair correlation of friction data was obtained for both entrances. The entrance configuration had little effect on the average heat-transfer and friction coefficients.