Report presenting measurements of the pitot-pressure distributions in the flow field, pressure distributions over the body, and downwash distributions through shed vortices for an inclined body of revolution at a free-stream Mach number of 1.98. Results regarding the experimental pressure distributions and vortex positions, vortex strengths computed from experiment, comparisons of theoretical and experimental vortex paths, and comparisons of theoretical and experimental downwash distributions through the body vortices are provided.

Report presenting a procedure for estimating the range of peak airplane load factors and maneuvering tail loads likely to be experienced in pitch-up maneuvers. Results of computations indicated that though the load factors and maneuvering tail loads were not critical in pitch-up maneuvers at 35,000 feet, they were likely to exceed design levels at 15,200 feet.

Report discussing available wind-tunnel data on low-speed horizontal-tail contribution to the static longitudinal stability of high-speed airplane configurations with unswept and sweptback wings. The effects of variations of tail position, wing plan form, airfoil section, trailing-edge flaps, stall-control devices, and ground interference on air-flow characteristics an tail contribution are also described.

Memorandum presenting a low-speed investigation in the free-flight tunnel to determine the effect of small canard surfaces on the directional stability of a fighter-airplane model with an aspect ratio of 3.4 and a 42 degree sweptback wing. The canard surfaces were found to be generally ineffective at angles of attack below 20 degrees.

Report presenting an investigation of the aerodynamic characteristics of various configurations of the Republic F-105 at Mach numbers from 0.60 to 1.13. The primary focus of this report are the static lateral and directional stability and control characteristics of the model. Results regarding force and moment results, longitudinal characteristics, lateral and directional characteristics.

An altitude-test-chamber investigation of a 28-inch-diameter ram-jet engine at a simulated flight Mach number of approximately 2.0 for altitudes of 40,000 to 50,000 feet was conducted at the NACA Lewis laboratory. Three different flame holders, varying in the number and size of the annular gutters, in conjunction with several fuel-injection systems were investigated. The combustion efficiency for the flame-holder fuel-injection system that provided the best over-all operational fuel-air-ratio range (0.03 to 0.075) was over 0.9 at a fuel-air ratio of about 0.065 for the altitude range investigated.

A heat-transfer investigation was conducted with air flowing through an electrically heated Inconel tube having either a long-approach or a right-angle-edge entrance, an inside diameter of 0.402 inch, and a length of 24 inches over a range of Reynolds numbers up to 375,000 and average inside-tube-wall temperatures up to 2000 degrees R. Good correlation of heat-transfer data was obtained for both entrances, which substantiates work previously reported. A fair correlation of friction data was obtained for both entrances. The entrance configuration had little effect on the average heat-transfer and friction coefficients.

Report presenting an investigation to determine the lateral control characteristics of a 20-percent-chord flap-type aileron of various spans on a semispan wing-fuselage model in the transonic speed range. The wing of the model had 45 degrees of sweepback, an aspect ratio of 3.7, a taper ratio of 1.0, and an NACA 65A009 airfoil section parallel to the free stream.

Report presenting the first sample of time-history data of airspeed, altitude, and normal accelerations obtained by the NACA VGH recorder in transport operations. This data defines the distribution of normal accelerations and airspeeds in greater detail than what was obtainable with the V-G recorder. Results regarding effective gust velocities, proportion of time spent in rough air, values of airspeed in descent, and variations in load experience are provided.

The nature of the flow at the exit of a row of turbine blades for the range of conditions represented by four different blade configurations was evaluated by the conservation-of-momentum principle using static-pressure surveys and by analysis of Schlieren photographs of the flow. It was found that for blades of the type investigated, the maximum exit tangential-velocity component is a function of the blade geometry only and can be accurately predicted by the method of characteristics. A maximum value of exit velocity coefficient is obtained at a pressure ratio immediately below that required for maximum blade loading followed by a sharp drop after maximum blade loading occurs.

Memorandum presenting an investigation in the supersonic pressure tunnel to determine the static longitudinal stability and control characteristics of several missiles at a Mach number of 2.01. The present paper consists largely of a data presentation of the results obtained at combined angles of pitch and sideslip. Appendices are included in which the body, wind, and stability-axes systems are described and the transfer equations necessary to convert the basic data to other forms are shown.

Memorandum presenting the effects of resin coating methods on some physical properties of laminates prepared with glass fabric, Fiberglas 181, and bonded with two commercial polyester resins. The resins used were Laminac 4126 and Selectron 5003. The resin coating methods used were roller coating, application of a dilute solution of resin, resin immersion, application of monomeric styrene, and vacuum impregnation.

Report presenting a study of the application of Wiener filter theory to the design of a beam-rider guidance system operating in the presence of glint noise. The theory is then used to establish the theoretical lower limit of root-mean-square error and the corresponding desired transfer-function characteristics.

Report presenting a wind-tunnel investigation at low speed in the 300 mph 7- by 10-foot tunnel to determine the effect of deflector projection on the control effectiveness of spoiler-slot-deflectors on a 30 degree sweptback wing-fuselage model equipped with either a 15-percent-chord spoiler or a spoiler-slot-deflector. Results regarding the aerodynamic characteristics, wing longitudinal characteristics, rolling-moment characteristics, and pressure distributions are provided.

Report presenting an investigation in the 4- by 4-foot supersonic pressure tunnel to determine the effects of various external-store configurations on the longitudinal and lateral aerodynamic characteristics of a model of a 45 degree swept-wing fighter airplane. Results regarding accuracy and remarks on effects of stores are provided.

Report presenting an investigation in the 4- by 4-foot supersonic pressure tunnel to determine the effects of the addition of one body-mounted external store, tip tanks, and several tip-mounted missile configurations on the aerodynamic characteristics in pitch of a fighter model with a low-aspect-ratio, unswept wing at Mach number 1.82. Many of the tip-mounted store configurations were found to produce increased lift-curve slopes and drag increments which decreased with increasing lift coefficient above lift coefficients of about 0.06.

Report presenting an investigation of the hydrodynamic characteristics of a multijet water-based aircraft capable of supersonic speeds and with jet engines exhausting through the step. The step engine exhausts were found to considerably increase afterbody wetting and smooth-water resistance, but they had no significant effect on longitudinal stability. Results regarding spray characteristics, resistance and stability at constant speed, take-off stability, landing stability, and jet noise are provided.

Report presenting measurements of the skin temperature and surface pressure on a large-scale, highly polished nose with a relatively sharp-tipped 100 degree total-angle cone followed by a conical flare section of 10 degree half-angle. Heating on the forward 3.0 to 4.5 inches of the 100 degrees cone was generally lower than that on the rearward portion.

Report discussing testing to determine the effects of control profile on the dynamic hinge-moment and flutter characteristics of a trailing-edge flap-type control. A conventional control and two control profile modifications were examined. Information about spring moments is also provided.

Memorandum presenting a flight investigation using pulse techniques to determine longitudinal and lateral dynamic stability characteristics of the D-558-II research airplane with particular reference to the jet exhaust effects of the rocket engine. Results regarding the longitudinal stability characteristics, and lateral stability characteristics are provided.

"Altitude performance characteristics of the J65-B3 turbojet engine and its components were obtained at engine-inlet conditions corresponding to Reynolds number indices from 0.2 to 0.8 over a range of corrected engine speeds from 70 to 110 percent of rated speed. Engine operational limits up to an altitude of 75,000 feet together with ignition and windmilling characteristics were also obtained. The engine and component data are presented both in graphical and in tabulated form. The operational characteristics are presented in graphical form" (p. 1).

A brief summary is made of methods available to the helicopter designer for obtaining desired stability characteristics by modifications to the airframe design. The discussion is based on modifications made during the establishment of flying-qualities criteria and includes sample indications of theoretical studies of additional methods.

An investigation was conducted to relate the engine performance of the heat-resistant alloys, Stellite 21, Hastelloy B, cast S-816, forged S-816, X-40, Nimonic 80, Refractory 26, N-155, and Iconel X to their stress-rupture properties. The engine test consisted of the repetition of a 20-minute cycle, 15 minutes at rated speed and approximately 5 minutes at idle. The results of the investigation indicated a direct correlation between stress-rupture life and blade life for the relatively low-strength alloys. The stress-rupture life and blade life for the relatively high-strength alloys did not correlate because of the effects of the vibratory stresses and the corrosive-gas atmosphere.

Report presenting a wind-tunnel investigation on two series of twisted and cambered wings, which were identical except for wing section, to compare the effects of NACA 4-digit and NACA 64A chordwise distributions of thickness on the longitudinal aerodynamic characteristics of the wings. Results regarding the low-speed results, high-speed results, and flow studies are provided.