Report presenting measurements of the pitot-pressure distributions in the flow field, pressure distributions over the body, and downwash distributions through shed vortices for an inclined body of revolution at a free-stream Mach number of 1.98. Results regarding the experimental pressure distributions and vortex positions, vortex strengths computed from experiment, comparisons of theoretical and experimental vortex paths, and comparisons of theoretical and experimental downwash distributions through the body vortices are provided.

Report presenting the results of a wind-tunnel investigation to determine the effects of a variation in wing taper ratio on the longitudinal characteristics of a wing-body combination at a variety of Mach numbers. The wings had an aspect ratio of 3, an unswept midchord line, and an NACA 64A003 profile. Results regarding the lift and pitching-moment characteristics and drag characteristics are provided.

Report presenting a procedure for estimating the range of peak airplane load factors and maneuvering tail loads likely to be experienced in pitch-up maneuvers. Results of computations indicated that though the load factors and maneuvering tail loads were not critical in pitch-up maneuvers at 35,000 feet, they were likely to exceed design levels at 15,200 feet.

Report discussing available wind-tunnel data on low-speed horizontal-tail contribution to the static longitudinal stability of high-speed airplane configurations with unswept and sweptback wings. The effects of variations of tail position, wing plan form, airfoil section, trailing-edge flaps, stall-control devices, and ground interference on air-flow characteristics an tail contribution are also described.

Report presenting an investigation of an inlet mounted on the side of a fuselage and utilizing a horizontally oriented 14 degree ramp located at the top of the inlet at a variety of Mach numbers. The characteristics of this inlet were compared to a conventional ramp-type side inlet. Results regarding the pressure recovery and model drag coefficients, spillage drag coefficients, and thrust minus drag comparison are provided.

Report presenting an examination of the most promising air-cooled turbine blades for conventional turbojet engines, which are convection-cooled corrugated-insert and strut-supported blades. Successful analytical methods of predicting blade temperatures have been found for both blades. Results regarding turbine-engine performance, turboprop-engine performance, performance variations with compressor-discharge air bleed, and some cooling methods are provided.

Memorandum presenting testing of an NACA 65(sub 06)A004 airfoil to determine the effects of a solid-strip spoiler on buffeting forces. Fluctuations of both section normal-force coefficient and of section pitching-moment coefficient are presented as functions of angle of attack and of section normal-force coefficient. Generally, the spoiler decreased the fluctuating section normal-force and pitching-moment coefficients if comparison is made at constant angle of attack and increased these coefficients if comparison is made at constant section normal-force coefficient.

Report presenting an investigation of a total of 31 flame-holder elements that can be classified into 7 distinct types under simulated afterburner operating conditions to determine their merit and feasibility for use in a high-velocity gas stream. The results indicated that a screen-type flame holder could far exceed the velocity limits of the same size conventional V-gutter at fuel-air ratios below about 0.045.

Report presenting studies of the final attack phase of an automatically controlled interceptor in flight and electronic simulators to investigate various airplane command and stabilization networks and to develop simple but adequate simulation techniques for the synthesis of automatic control systems. Results regarding automatic control with a simple command system, automatic control with the improved command system, and evaluation of the automatic control system in typical final attack maneuvers are provided.

Report presenting the effect of small variations in the axial position of the liner with respect to the nozzle on limiting rates of change of fuel flow and steady-state combustion efficiencies in a single tubular combustor. Data were obtained with two liner configurations at three combustor-inlet conditions. Results regarding transient combustion performance and steady-state combustion performance are provided.

Report presenting an experimental investigation to assess the effects of sweep and taper ratio on the longitudinal characteristics of a wing-body combination at a range of Mach numbers. The results indicated that increased leading-edge sweep caused a progressive decrease in lift-curve slope and the variation of Mach number of the lift-curve slope and static longitudinal stability. Results regarding the effect of sweep, effect of taper ratio, and comparison with results of a previous investigation are provided.

Report presenting an investigation of the overall performance of a modified eight-stage axial-flow compressor as part of the investigation of the problems encountered in a high-pressure-ratio axial-flow compressor with transonic inlet stages. The maximum total pressure ratio obtained at design speed was 11.0 at an equivalent weight flow of 70.9 pounds per second with an adiabatic efficiency of 0.81. Results regarding modified compressor performance and comparison with predicted performance are provided.

Report presenting measurements of boiling burn-out heat flux for water flowing upward through an electrically heated tube for ranges of velocity, pressure, length-diameter ratios, and subcooling.

From Introduction: "Data on the extent of decomposition of a sample of aluminum borohy-dride during long-term storage are presented."

Report presenting a compressor-rotor-blade vibration survey on a production turbojet engine incorporating a 13-stage axial-flow compressor with a pressure ratio of approximately 7 and an air flow of 120 pounds per second. The investigation was conducted due to the major problem that fatigue failures of compressor rotor blades have caused in the development of the axial-flow compressor. Results regarding rotating stall characteristics, rotor-blade vibration, and fourth-stage rotor-blade failure are provided.

Report presenting an investigation in the transonic blowdown tunnel at Mach numbers from 0.63 to 1.41 to determine increments in lift, drag, and pitching moment of a sweptback semicircular air inlet installed in the root of a 45 degree sweptback wing. Results regarding internal pressures and inlet performances are provided.

Report of an investigation of the effect of mode of engine operation, engine configuration, and airplane flight condition on the performance and design requirements of a turboprop engine with a high-pressure-ratio single-spool compressor. Both single-spool engines and gas-generating engines are considered. The free-turbine engine was found to be less versatile than the single-spool engine because the range of turbine-inlet temperature over which it can operate is restricted.

Report presenting testing of two beams of three web types which were loading in bending and subjected to rapid skin heating at rates from about 50 to 70 degrees Fahrenheit per second. The investigation was meant to determine some of the effects that rapid skin heating would have on the buckling and failing strength of multiweb-wing structures. The three types of web tested included the channel web, corrugated web, and truss web.

Report presenting a study of the application of Wiener filter theory to the design of a beam-rider guidance system operating in the presence of glint noise. The theory is then used to establish the theoretical lower limit of root-mean-square error and the corresponding desired transfer-function characteristics.

Report presenting a cycle analysis of a turboprop engine for various modes of operation over a range of flight conditions in order to determine whether one mode of operation has any marked advantages. The methods of operation explored included constant compressor equivalent design speed, constant design engine rotative speed, adjustable turbine stators, and variable exhaust-nozzle area.

From Summary: "An investigation was made to evaluate several design variations of hollow turbine blades intended for missile-engine use. In one general type, the airfoils were formed from sheet metal; in a second type, the blades were cast. The blades were operated in J47 engine at 7950 rpm turbine speed and 1260 degrees Fahrenheit tail-pipe temperature until a failure occurred or a service life of 30 hours had been attained."

"Spatial burnout calculations have been made of two types of water moderated cylindrical reactor using boron as a burnable poison to increase reactor life. Specific reactors studied were a version of the Submarine Advanced Reactor (sAR) and a supercritical water reactor (SCW). Burnout characteristics such as reactivity excursion, neutron-flux and heat-generation distributions, and uranium and boron distributions have been determined for core lives corresponding to a burnup of approximately 7 kilograms of fully enriched uranium" (p. 1).

"During an investigation of the J57-P-1 turbojet engine in the Lewis altitude wind tunnel, effects of inlet-flow distortion on engine stall characteristics and operating limits were determined. In addition to a uniform inlet-flow profile, the inlet-pressure distortions imposed included two radial, two circumferential, and one combined radial-circumferential profile. Data were obtained over a range of compressor speeds at an altitude of 50,000 and a flight Mach number of 0.8; in addition, the high- and low-speed engine operating limits were investigated up to the maximum operable altitude" (p. 1).