"Aerodynamic data have been obtained for a fuselage forebody alone and for canopy-body configurations consisting of four different canopies mounted on a fuselage forebody. Two of the canopies had the same shape and size rearward of the windshield but one had a "flat" and the other a "vee" windshield. The remaining two canopies were located at different body stations and were geometrically similar. The data indicated that the drag of the flat-windshield model was consistently lower than that of the vee-windshield model" (p. 1).

Memorandum presenting experimental flutter Mach numbers for several solid, thin, rectangular cantilever wings with uniform section properties, low aspect ratio, and high relative density estimated from the results of previous tests at zero angle of attack. The experimental values are considered estimates, rather than determinations, in the high subsonic speed range because in that range the amplitude criterion was necessarily arbitrary. Results regarding conservatism of standard analysis relative to the experiment, closeness of analytical and experimental results, and interpretation of the analytical and experimental uncertainties are provided.

From Introduction: "The investigation reported herein was initiated to define further the effects on the aerodynamic characteristics and load distribution of a thin, sweptback wing of a low-pressure blowing system and also to provide information on which to base a more thorough study of a complete airplane configuration."

"A method is described for measuring the dynamic stability derivatives of a model airplane in a wind tunnel. The characteristic features of this system are that single-degree-of-freedom oscillations were used to obtain combinations of rolling, yawing and pitching motions; that the oscillations were excited and controlled by velocity feedback which permitted operation under conditions unfavorable for more conventional types of oscillatory testing; and that data processing was greatly simplified by using analog computer elements in the strain-gage circuitry. A small number of experimental data are included to illustrate the general scope of results obtainable with this system" (p. 1).

Memorandum presenting flight tests with a fighter airplane to study the effect of boundary-layer suction aft of the shock wave on airfoil drag at supercritical Mach numbers and high Reynolds numbers. Airfoil chord force was determined from pressure-distribution measurements obtained at a range of Mach numbers at steady dives. Results of the tests showed no measurable effect of suction for the suction coefficient available.

Report presenting a low-speed wind-tunnel investigation to determine the lateral control characteristics of extensible wing-tip ailerons on an untapered semispan wing with two configurations; one was unswept and had an aspect ratio of 3.13 and the other was swept back 45 degrees and had an aspect ratio of 1.59. Results regarding the plain-wing aerodynamic characteristics and lateral control characteristics are provided.

Report presenting a study of rocket-powered models at transonic speeds to determine the effect on the zero-lift drag coefficient of an indented fuselage modification and a thickened wing-root modification of a swept-wing airplane configuration. Results regarding the variation of drag coefficient with Mach number, effect of wing root thickening, and wing-plus-interference drag coefficients for the tested models are provided.

"Tabulated pressure coefficients and aerodynamic characteristics are presented for six spanwise stations on the left wing of the Bell X-1 research airplane. These data were obtained in an unaccelerated low-speed stall, in push-overs at Mach numbers of approximately 0.83 and 0.99, and in a pull-up at a Mach number of approximately 1.16" (p. 1).

The forced-convection heat-transfer characteristics of lead-bismuth eutectic were experimentally investigated. Experimental values of Nusselt number for lead-bismuth fell considerably below predicted values. The addition of a wetting agent did not change the heat transfer characteristics.

Report presenting an investigation to determine the control characteristics of flap-type controls of various chords and spans on an unswept wing with a modified double-wedge section, an aspect ratio of 2.5, and a taper ratio of 0.625.The control chords in the study were 25, 35, and 45 percent of the wing chord, and the control spans were 25, 50, and 75 percent of the wing semispan. The data from the study indicated that the control-parameter values are approximately proportional to control chord or span for the chords tested.

Memorandum presenting results of compressive tests on duplicate longitudinal specimens from sheets of 76S-T6 and R301-T aluminum alloys in three thicknesses as graphs of tangent modulus, secant modulus, and are plotted against stress on a dimensionless basis.

Report presenting an investigation of the aerodynamic problems associated with turbine blades with relatively low solidity and thick profiles, which makes them suitable for use in air-cooled turbines, in a two-dimensional cascade. Testing indicated that supersonic velocities may be obtained over the greater portion of the blade suction surface, resulting in high blade loading without an appreciable decrease in efficiency from that obtained using blades with lower velocities.

Memorandum presenting an investigation of the effect of a propulsive jet on the drag and pressure distribution of the NACA RM-10 missile configuration at large Reynolds numbers that utilized rocket models between Mach numbers 0.8 and 3.0. Pressures were measured along the body, near the fin root, and at the base. Results regarding basic data, body pressures, fin pressures, and drag are provided.

"A transonic wind-tunnel investigation was made in the Langley 8-foot transonic pressure tunnel at the request of the Bureau of Aeronautics, Department of the Navy, of the static longitudinal stability and control characteristics and drag of a 0.05-scale model of the Chance Vought XF8U-3 airplane at Mach numbers from 0.80 to 1.20 with an average Reynolds number of 2.6 x 10(exp 6). The investigation included effects of the addition of the ventral fins, extension and removal of the missiles, deflection of the speed brake, addition of a fuselage fairing near the wing leading edge, and longitudinal control effectiveness. The model was statically stable throughout most of the range of positive lift coefficients, but some loss in horizontal-tail effectiveness may be expected near zero lift and a Mach number of 1.0" (p. 1).

An analysis of rim cooling, which cools the blade by condition alone, was conducted. Gas temperatures ranged from 1300 degrees to 1900 degrees F and rim temperatures from 0 degrees to 1000 degrees F below gas temperatures. Results show that gas temperature increases up to 200 degrees F are permissible provided that the blades are cooled by 400 degrees to 500 degrees F below the gas temperature. Relatively small amounts of blade cooling, at constant gas temperature, give large increases in blade life. Dependence of rim cooling on heat-transfer coefficient, blade dimensions, and thermal conductivity is determined by a single parameter.