The purpose of this study was to characterize typical levels and variability of 60Hz magnetic fields at the centerline and edge of right-of-way of Bonneville Power Administration (BPA) 230-kV and 500-kV transmission lines. This was accomplished by taking magnetic field measurements at over 800 spans in Oregon and Washington. The spans were sampled using a stratified random sampling procedure with region (East vs. West), voltage (230-kV vs 500-kV), and circuit configuration as strata. There were five different circuit configuration groups for each region/voltage category requiring a total of 200 strata. Magnetic field measurements were taken at 13 locations under each span using an EMDEX-C as a survey meter. Additional information recorded for each span included conductor height (at 10 locations), right-of-way width, longitudinal and lateral slope, time of day, vegetation, terrain, weather conditions, temperature, wind speed, span length and presence of other lines in the corridor. 9 refs., 17 figs., 26 tabs.

The objective of this research is to elucidate the role of various chemical additives on ethanol synthesis over Rh- and Ni-based catalysts. Chemical additives used for this study will include S, P, Ag, Cu, Mn, and Na which have different electronegativities. The effect of additives on the surface state of the catalysts, heat of adsorption of reactant molecules, reaction intermediates, reaction pathways, reaction kinetics, and product distributions is/will be investigated by a series of experimental studies of NO adsorption, reaction probing, study state rate measurement, and transient kinetic study. A better understanding of the role of additives on the synthesis reaction may allow us to use chemical additives to manipulate the catalytic properties of Rh- and Ni-based catalysts for producing high yields of ethanol from syngas. 27 refs. 7 figs., 2 tabs.

The objective of this research is to elucidate the role of various chemical additives on ethanol synthesis over Rh- and Ni-based catalysts. Chemical additives used for this study will include S, P, Ag, Cu, Mn, and Na which have different electronegativities. The effect of additives on the surface state of the catalysts, heat of adsorption of reactant molecules, reaction intermediates, reaction pathways, reaction kinetics, and product distributions is/will be investigated by a series of experimental studies of NO adsorption, reaction probing, study state rate measurement, and transient kinetic study. A better understanding of the role of additives on the synthesis reaction may allow us to use chemical additives to manipulate the catalytic properties of Rh- and Ni-based catalysts for producing high yields of ethanol from snygas. 27 refs., 2 figs., 2 tabs.

The Hanford Site Environmental Report is prepared annually to summarize environmental data and information, describe environmental management performance, and demonstrate the status of compliance with environmental regulations. The report also highlights major environmental programs and efforts. The following sections: describe the Hanford Site and its new mission; summarize the status in 1990 of compliance with environmental regulations; describe the environmental programs at the Hanford Site; present information on environmental surveillance and the ground-water protection and monitoring program; and discuss activities to ensure quality.

Circulating fluidization is a promising technology for designing efficient coal combustors with high solid feed rates. Unfortunately, limited understanding of circulating fluidized beds (CFB) has rendered design extrapolations from pilot reactors to full-scale plants both empirical and expensive. In CFBs, hydrodynamics and heat transfer are difficult to predict, and the behavior of the flow under scale-up is unclear. Thus the objectives of this research were to quantify the effect of scale-up on the hydrodynamics of CFB combustors, to carry out a rigorous analysis of the flow and heat transfer in vertical gas-solid risers, and to interact with industry at all stages of this work. The importance of this research resides in the great number of CFB coal-burning powerplants that may benefit from its results. At the completion of this work, the results have exceeded the expectations outlined in the original proposal. The present report summarizes these accomplishments, which have led to five archival publications, two reviewed conference papers, twelve presentations, various quarterly reports, and the award of five graduate degrees.

The US Department of Energy's Office of Health and Environmental Research (OHER) has supported work in our laboratory since 1977. The general theme of this program has been the identification of potentially toxic organic compounds associated with various combustion effluents, following the fates of these compounds in the environment, and improving the analytical methodology for making these measurements. The projects currently investigation include: an improved sampler for semi-volatile compounds in the atmosphere; the wet and dry deposition of dioxins and furans from the atmosphere; the photodegradation and mobile sources of dioxins and furans; and the bioaccumulation of PAH by tree bark. These projects are all responsive to OHER's interest in the pathways and mechanisms by which energy-related agents move through and are modified by the atmosphere''. The projects on gas chromatographic and liquid chromatographic tandem mass spectrometry are both responsive to OHER's interest in new and more sensitive technologies for chemical measurements''. 35 refs., 9 figs.

With support provided by the LLNL Accelerator Mass Spectrometry Laboratory, the UCR Radiocarbon Laboratory continued its studies involving sample pretreatment and target preparation for both AMS radiocarbon ({sup 14}C) and radiocalcium ({sup 41}Ca) involving applications to archaeologically -- and paleoanthropologically- related samples. With regard to AMS {sup 14}C-related studies, we have extended the development of a series of procedures which have, as their initial goal, the capability to combust several hundred microgram amounts of a chemically-pretreated organic sample and convert the resultant CO{sub 2} to graphitic carbon which will consistently yield relatively high {sup 13}C{sup {minus}} ion currents and blanks which will yield, on a consistent basis, {sup 14}C count rates at or below 0.20% modern, giving an 2 sigma age limit of >50,000 yr BP.

The major goal is to provide the simulation tools for modeling both conventional and advanced coal cleaning technologies. This DOE project is part of a major research initiative by the Pittsburgh Energy Technology Center (PETC) aimed at advancing three advanced coal cleaning technologies- heavy-liquid cylconing, selective agglomeration, and advanced froth flotation through the proof-of- concept (POC) level. The commercially available ASPEN PLUS process simulation package will be extended to handle coal applications. Algorithms for predicting the process performance, equipment size, and flowsheet economics of commercial coal cleaning devices and related ancillary equipment will be incorporated into the coal cleaning simulator. This report is submitted to document the progress of Aspen Technology, Inc. (ApsenTech), its contractor, ICF Kaiser Engineers, Inc., (ICF KE) and CQ Inc., a subcontractor to ICF KE, for the seventh quarterly reporting period, April through June 1991. ICF KE is providing coal preparation consulting and processing engineering services in this work and they are responsible for recommending the design of models to represent conventional coal cleaning equipment and costing of these models.

A simple mixing-length estimate of diffusion of alphas particles by toroidicity-induced shear Alfven eigenmodes (TAE) is used, in zero and one-dimensional models, to evaluate the importance of diffusion of meeting ignition requirements for ITER and other next-generation burning plasma experiments. It is found that, depending on a number of assumptions, diffusion could reduce that effectiveness of alpha heating in the core as much as an order of magnitude. However, the effect would be less if only alphas resonant with the Alfven waves diffuse. Also, in the Appendix it is argued that the mixing length diffusion formula, though qualitatively reasonable, may be an over estimate. 12 refs., 7 figs., 1 tab.

The objective of this research is to elucidate the role of various chemical additives on ethanol synthesis over Rh- and Ni-based catalysts. Chemical additives used for this study will include S, P, Ag, Cu, Mn, and Na which have different electronegativities. The effects of additives on the surface state of the catalysts, heat of adsorption of reactant molecules, reaction intermediates, reaction pathways, reaction kinetics, and product distributions is/will be investigated by a series of experimental studies of NO adsorption, reaction probing, study state rate measurement, and transient kinetic study. A better understanding of the role of additives on the synthesis reaction may allow us to use chemical additives to manipulate the catalytic properties of Rh- and Ni-based catalysts for producing high yields of ethanol from syngas.

The purpose of this monograph is to start a theory of deterrence which has the capability of quantitatively answering the question of what is required to deter a nation or alliance from certain acts. Despite the existence of voluminous writing on deterrence, from the beginning of the nuclear age and even before, none of it attempts a theoretical discussion of how to calculate what it takes to deter a country from committing some acts which are objectionable to another country. Many theories of deterrence have already been created. They have exclusively been of two separate forms -- those of the social scientists, which deal with political questions, and how the concept of mass destruction psychological deters the initiation of war; and those of the mathematicians, who model the quantities of one country`s arsenal of strategic systems needed to destroy a certain portion of another country`s. Only the latter is quantitative, but they lack an essential element added to answer the question ``How much is enough?`` In order to use the techniques of operations research on the questions of what type and amount of weapons are adequate for deterrence, the definitions of quantities occurring in the calculations need to be made …

The objective of this research is to elucidate the role of various chemical additives on ethanol synthesis over Rh- and Ni-based catalysts. Chemical additives used for this study will include S, P, Ag, Cu, Mn, and Na which have different electronegativities. The effects of additives on the surface state of the catalysts, heat of adsorption of reactant molecules, reaction intermediates, reaction pathways, reaction kinetics, and product distributions is/will be investigated by a series of experimental studies of NO adsorption, reaction probing, study state rate measurement, and transient kinetic study. A better understanding of the role of additives on the synthesis reaction may allow us to use chemical additives to manipulate the catalytic properties of Rh- and Ni-based catalysts for producing high yields of ethanol from syngas.

Circulating fluidization is a promising technology for designing efficient coal combustors with high solid feed rates. Unfortunately, limited understanding of circulating fluidized beds (CFB) has rendered design extrapolations from pilot reactors to full-scale plants both empirical and expensive. In CFBs, hydrodynamics and heat transfer are difficult to predict, and the behavior of the flow under scale-up is unclear. Thus the objectives of this research were to quantify the effect of scale-up on the hydrodynamics of CFB combustors, to carry out a rigorous analysis of the flow and heat transfer in vertical gas-solid risers, and to interact with industry at all stages of this work. The importance of this research resides in the great number of CFB coal-burning powerplants that may benefit from its results. At the completion of this work, the results have exceeded the expectations outlined in the original proposal. The present report summarizes these accomplishments, which have led to five archival publications, two reviewed conference papers, twelve presentations, various quarterly reports, and the award of five graduate degrees.

The Hanford Site Environmental Report is prepared annually to summarize environmental data and information, describe environmental management performance, and demonstrate the status of compliance with environmental regulations. The report also highlights major environmental programs and efforts. The following sections: describe the Hanford Site and its new mission; summarize the status in 1990 of compliance with environmental regulations; describe the environmental programs at the Hanford Site; present information on environmental surveillance and the ground-water protection and monitoring program; and discuss activities to ensure quality.

This is the sixth Technical Progress Report, describing work performed under DOE Contract No. DE-FC22-90PC89663, ``Development of a Coal Quality Expert.`` The contract is a Cooperative Agreement between the US Department of Energy, CQ Inc., and Combustion Engineering, Inc. This report covers the period from July 1 through September 30, 1991. Four companies and seven host utilities have teamed with CQ Inc. and C-E to perform the work on this project. The work falls under DOE`s Clean Coal Technology Program category of ``Advanced Coal Cleaning.`` The 45-month project will provide the utility industry with a PC expert system to confidently and inexpensively evaluate the potential for coal cleaning, blending, and switching options to reduce emissions while producing lowest cost electricity. Specifically, this project will: Enhance the existing Coal Quality Information System (CQIS) database and Coal Quality Impact Model (CQIM) to allow confident assessment of the effects of cleaning on specific boiler cost and performance; and develop and validate a methodology, Coal Quality Expert (CQE) which allows accurate and detailed predictions of coal quality impacts on total power plant capital cost, operating cost, and performance based upon inputs from inexpensive bench-scale tests. The project consists of the following seven tasks: Project …

The objective of this study is to develop technology that permits the practical and economic preparation, storage, handling, and transportation of coal pellets, which can be formulated into Coal-Water Fuels (CWFs) suitable for firing in small- and medium-size commercial and industrial boilers, furnaces, and engines.

Table 1 indicates that the stiffest line is the cryogenic vent line while the most flexible line is the 6 inch insulating vacuum line. The table also shows that the four remaining lines are roughly of the same stiffness. This follows closely with the experience of installing the U-tubes in the assembly hall. The vent line was by far the stiffest, while the other lines are comparitively more flexible. However, the value for the LAr line is misleading. It is as flexible as the other 1 1/2 x 3 lines. Using this as a basis, the collision hall connections should be slightly more stiff, but not appreciably. The vent line represents the only anticipated 'difficulty'. Provided that the building piping is constructed to reasonable tolerances, there should be no need to modify the existing U-tubes for use in the Collision hall. The analysis makes many assumptions which are not completely valid. For example, the inner line is much more flexible than the table indicates. Thus the analysis should not be taken as an absolute measure of the amount of force necessary to deflect the lines. The analysis does provide a means of comparison between individual lines and between the assembly …

The original objects of this research program were: to interface d.c. plasma atomic emission spectrometer with an ion chromatograph; to characterize and optimize the combined systems for application in the speciation of metals in aqueous solutions; to use this system in the study of the solution chemistry of various metals; and to find ways in which the measurement sensitivity of the method can be enhanced, thereby allowing the detection of metal species at low ppb concentration levels. This approach has been used to study the chemistry of and speciate several elements in solution including: arsenic, chromium, iron, manganese, nickel phosphorus, platinum, selenium, and vanadium. During the course of this research, we have found that the solution chemistry of the elements studied and the speciation data obtained can vary considerably depending on the solution, and the chromatographic conditions employed. The speciation of chromium, iron, and vanadium was found to be highly influenced by the acidity of the sample. The element selective nature of the d.c. plasma detector allows these changes to be monitored, thereby providing quantitative information on the new moieties formed. New approaches are being developed including the use of chelating ligands as preconcentration agents for purposes of reducing further …

The project will provide the utility industry with a PC expert system to confidently and inexpensively evaluate the potential for coal cleaning, blending, and switching options to reduce emissions while producing lowest cost electricity. Specifically, this project will: (1) Enhance the existing Coal Quality Information System (CQIS) database and Coal Quality Impact Model (CQIM) to allow confident assessment of the effects of cleaning on specific boiler cost and performance; (2) Develop and validate a methodology, Coal Quality Expert (CQE) which allows accurate and detailed predictions of coal quality impacts on total power plant capital cost, operating cost, and performance based upon inputs from inexpensive bench-scale tests.

The objective of this study is to develop technology that permits the practical and economic preparation, storage, handling, and transportation of coal pellets, which can be formulated into Coal-Water Fuels (CWFs) suitable for firing in small- and medium-size commercial and industrial boilers, furnaces, and engines.

Objective was to develop a mathematical model of the cupola furnace (cast iron production) in on-line and off-line process control and optimization. In Phase I, the general structure of the heat transfer, fluid flow, and chemical models were laid out, providing reasonable descriptions of cupola behavior with a one-dimensional representation. Work was also initiated on a two-dimensional model. Phase II was focused on perfecting the one-dimensional model. The contributions include these from MIT, Michigan University, and GM.

A high activity Waste Tank cooling coil supply line cracked on September 12, 1991 at the H-Area East pump house, draining the cooling water to the ground. This raised the possibility of draining high-activity waste to the ground by siphon action through the submerged cycling coils since some of the cooling water supply lines are located up to 40 ft. below waste tank liquid level. The following documentation summarizes conclusions and provides details of flow calculation presented earlier during the incident investigation. No plausible reason for a simultaneous rupture of the supply line and the cooling coils inside the tank was identified. Both seismic stresses and water hammer produce relatively low stresses on the cooling coils. A hypothetical simultaneous rupture of the cooling coils inside the tank and the supply line below ground could result in 100 to 200 gpm waste discharge to the ground. Waste discharge from a possible cooling coil corrosion leak would be limited to 20 gal/12-hr shift under maximum possible siphon, based on operating procedures for cooling water makeup which call for coil isolation when a cooling water loss of 40 gal/shaft is identified. This level of discharge is within the existing envelope of accident consequences …

The major goal is to provide the simulation tools for modeling both conventional and advanced coal cleaning technologies. This DOE project is part of a major research initiative by the Pittsburgh Energy Technology Center (PETC) aimed at advancing three advanced coal cleaning technologies- heavy-liquid cylconing, selective agglomeration, and advanced froth flotation through the proof-of- concept (POC) level. The commercially available ASPEN PLUS process simulation package will be extended to handle coal applications. Algorithms for predicting the process performance, equipment size, and flowsheet economics of commercial coal cleaning devices and related ancillary equipment will be incorporated into the coal cleaning simulator. This report is submitted to document the progress of Aspen Technology, Inc. (ApsenTech), its contractor, ICF Kaiser Engineers, Inc., (ICF KE) and CQ Inc., a subcontractor to ICF KE, for the seventh quarterly reporting period, April through June 1991. ICF KE is providing coal preparation consulting and processing engineering services in this work and they are responsible for recommending the design of models to represent conventional coal cleaning equipment and costing of these models.

Reburning is examined as a means of NO{sub x} destruction in a 17 kW down-fired pulverized coal combustor. In reburning, a secondary fuel is introduced downstream of the primary flame to produce a reducing zone, favorable to NO destruction, and air is introduced further downstream to complete the combustion. Emphasis is on natural gas reburning and a bituminous coal primary flame. A parametric examination of reburning employing a statistical experimental design, is conducted, complemented by detailed experiments. Mechanisms governing the inter-conversion of nitrogenous species in the fuel rich reburn zone is explored. The effect of reburning on N{sub 2}O emissions, the effect of primary flame mode (premixed and diffusion) and the effect of distributing the reburning fuel, are also investigated.