Tests to evaluate the effect of a conical windshield on the drag of a bluff body at supersonic speeds were performed for the following configurations: a sharp nose fuselage with stabilizing fins,a blunt nose fuselage with a hemispherical shape, and a blunt nose fuselage with a conical point. Results of the drag coefficient are described at Mach 1.0 and the greatest Mach number of 1.37.

Flight and ground investigations have been made to compare an exhaust-ejector installation with a standard exhaust-collector-ring installation on air-cooled aircraft engines in a twin-engine airplane. The ground investigation allowed that, whereas the standard engine would have overheated above 600 horsepower, the engine with exhaust ejectors cooled at take-off operating conditions at zero ram. The exhaust ejectors provided as much cooling with cowl flaps closed as the conventional cowl flaps induced when full open at low airspeeds. The propulsive thrust of the exhaust-ejector installation was calculated to be slightly less than the thrust of the collector-ring-installation.

"This report contains the results of tests of a 1/3-scale model of the Lockheed YP-90A "Shooting Star" airplane and a comparison of drag, maximum lift coefficient, and elevator angle required for level flight as measured in the wind tunnel and in flight. Included in the report are the general aerodynamic characteristics of the model and of two types of dive-recovery flaps, one at several positions along the chord on the lower surface of the wing and the other on the lower surface of the fuselage. The results show good agreement between the flight and wind-tunnel measurements at all Mach numbers" (p. 1).

"An untwisted wing, which when unswept has an NACA 65-210 section, an aspect ratio of 9.0 and a taper ration of 2.5:1.0, has been tested with no sweep, and 30 deg and 45 deg of sweepback and sweepforward in conjunction with a typical fuselage at Mach numbers from 0.60 to 0.96 at angles of attack generally between -2 deg and 10 deg in the Langley 8-foot high-speed tunnel. Sweep was obtained by rotating the wing semispans about a point in the plane of symmetry. The normal-force, pitching-moment, profile-drag, and loading characteristics for the wings have been obtained from pressure measurements and wake surveys" (p. 1).

"Tests were made with a 1/16 size dynamically similar model of the Navy XP2V-1 airplane to study its performance when ditched. The model was ditched in calm water at the Langley tank no. 2 monorail. Various landing attitudes, speeds, and conditions of damage were simulated" (p. 1).

The results obtained from measurements of gust velocities, draft velocities, and ambient-air temperature within thunderstorms for the period September 17, 1946 to September 18, 1946 at Orlando, Fla. are presented herein. These data are summarized in tables I, II, and III, respectively, and are of the type presented in reference 1 for previous flights.

Report presenting an investigation of surface static pressures over the outer and inner surfaces of the cockpit canopies on the Grumman F6F-3, Curtiss SB2C-4E, and Grumman F8F-1 airplanes in the full-scale tunnel. Results regarding the external pressure distribution and internal static pressure are provided.

Report presenting an investigation of three transonic fuselage-inlet installations designed to maintain substream velocities on the body ahead of air inlets. Surface pressures and inlet total pressures were measured at the tops of the test configurations for wide ranges of inlet-velocity ratio and angles of attack. Results indicated that substream velocities were maintained on all three noses over the angle of attack ranges and inlet-velocity ratio useful for high-speed flight.

"A study has been made of the variation of seaplane hull weight with length-beam ratio in a systematic series of hulls designed for constant gross weight and similar spray characteristics. It is found that increases in the length-beam ratio bring about small reductions in the hull weight if it is assumed that seaplanes having the same weight and bottom shape will be designed for the same load factor. A short discussion is also given to show the reduction in load factor that may occur with high length-beam ratios" (p. 1).

A wind-tunnel investigation of the Boeing XB-47 full-scale empennage was conducted to provide, prior to flight tests, data required on the effectiveness of the elevator and rudder. The XB-47 airplane is a jet-propelled medium bomber having wing and tail surfaces swept back 35 degrees. The investigation included tests of the effectiveness of the elevator with normal straight sides, with a buldged trailing edge, and with a modified hinge-line gap and tests of the effectiveness of the rudder with a normal straight-sided tab and with a bulged tab.

Report presenting an investigation of a 42 degree sweptback wing of aspect ratio 4, taper ratio 0.625, and NACA 64-series airfoil sections to study several proposed devices for increasing the maximum lift coefficient and improving the longitudinal stability characteristics of sweptback wings at the stall. Some of the devices tested included leading-edge flaps and slats, trailing-edge split and extended split flaps, upper-surface split flaps, and upper-surface fences. The results regarding the characteristics of the devices and the wing-fuselage combinations are described.

Theoretical pressure distributions and measured lift, drag, and pitching moment characteristics at three values of Reynolds number are presented for a group of NACA four-digit-series airfoil sections modified for high-speed applications. The effectiveness of flaps applied to these airfoils and the effect of standard leading-edge roughness were also investigated at one value of Reynolds number. Results are also presented of tests of three conventional NACA four-digit-series airfoil sections.

Report presenting an investigation of the problem of applying controls to low-aspect-ratio wings of triangular plan form by using the NACA wing-flow method with parallel-sided models with sharp leading and trailing edges. Results regarding the data analysis, Reynolds number and separation effects, flap effectiveness, plan-form characteristics, angle of zero lift, and triangular plan-form flying-wing characteristics are provided.