Report presenting an investigation at Mach number 1.91 to determine the gross spreading characteristics of jets expanding from convergent and convergent-divergent nozzles using total-temperature surveys. Results regarding the preliminary development and jet spreading characteristics of the different types of nozzles are provided.

"Results are presented of a free-flight investigation between Mach numbers of 0.7 to 1.3 and Reynolds numbers of 3.1 x 10(exp 6) to 7.0 x 10(exp 6) to determine the longitudinal aerodynamic characteristics of the Northrop MX-775A missile. This missile has a wing, body, and vertical tail, but has no horizontal tail. The basic wing plan form has an aspect ratio of 5.5, 45 deg of sweepback of the 0.406 streamwise chord line, and a taper ratio of 0.4" (p. 1).

From Introduction: "The results of two phases of this investigation, presented in references 1 and 2, have indicated possible ways of reducing hull drag without causing large changes in aerodynamic stability and hydrodynamic performance."

"Flight measurements of the stability characteristics of the Bell X-5 research airplane at 59 deg sweepback were made in steady sideslips at Mach numbers from 0.62 to 0.97 at altitudes ranging between 35,000 and 40,000 feet. The results showed that the apparent directional stability was positive and increased at Mach numbers above 0.90. The apparent effective dihedral was positive and high, increasing at Mach numbers above 0.75" (p. 1).

"During the acceptance tests of the Bell X-5 airplane, measurements of the static stability and control characteristics and horizontal-tail loads were obtained by the NACA High-Speed Flight Research Station. The results of the stability and control measurements are presented in this paper. A change in sweep angle between 20 deg and 59 deg had a minor effect on the longitudinal trim, with a maximum change of about 2.5 deg in elevator deflection being required at a Mach number near 0.85; however, sweeping the wings produced a total stick-force change of about 40 pounds" (p. 1).

Report presenting information regarding transient oscillations observed in response to elevator pulses of the Douglas D-558-I airplane at a range of Mach numbers and altitudes. An application of the Fourier transform was used to obtain the frequency-response characteristics. The effects of lift coefficient on the frequency response are also included.

From Summary: "Modifications A and B of impeller model MFI-1 and A, B, and C of impeller model MFI-2 were investigated experimentally in an attempt to determine what allowance in blade height should be made for boundary layer and viscous losses in an impeller designed for isentropic compressible flow. A gradual increase in blade height was arbitrarily made from inlet to outlet in anticipation of a gradual build-up of boundary layer. Apparently there was a rapid build-up of boundary layer near the inlet in the experimental case rather than a gradual one. Therefore, the proper allowance for boundary layer cannot be described from the data obtained."

Report presenting an investigation to determine the low-speed lateral characteristics of a triangular-wing airplane model. The model consisted of an aspect ratio 2 triangular wing in combination with a fuselage of fineness ratio 12.5, a thin, triangular, vertical tail with a constant-chord rudder, and a thin, unswept, all-movable horizontal tail.

Report presenting some preliminary time-history results of maneuvers performed during US Air Force squadron operations with an F-86A jet-fighter airplane. The information covers a speed range from stall to 530 mph-indicated airspeed and pressure altitudes varying from sea level to approximately 25,000 feet.

From Summary: "Data obtained from the NACA air-launched ram-jet program are summarized with emphasis placed upon the transonic propulsive thrust potential of the engines. Data are presented for boosted and non-boosted engine configurations which incorporate a single-oblique-shock or double-oblique-shock diffuser designed for critical inlet operation at flight Mach numbers of 1.8 and 2.4, respectively. The engines are evaluated in terms of flight Mach number, mass-flow ratio, diffuser pressure recovery, combustion-chamber heat release, propulsive thrust, external drag, and specific impulse. From specific impulse considerations, it appears that for some air-launched missile applications the self-accelerating supersonic ram jet may have a lower gross weight than a rocket-boosted ram jet."

An investigation was conducted to determine the combustion response to rapid fuel-flow changes in a single tubular combustor at two simulated altitude-rotor speed conditions of 25,000 feet-70 percent rated engine speed and 50,000 feet-70 percent rated engine speed. Limiting rates of change of fuel flow (acceleration limits) were determined and the effects of certain combustion air flow variables on the transient combustion characteristics were studied with the aid of rapid-response instrumentation.

Memorandum presenting results of a free-flight investigation over a range of Mach and Reynolds numbers to determine the longitudinal aerodynamic characteristics of the Northrop MX-775A missile. The missile has a wing, body, and vertical tail, but has no horizontal tail. Results regarding basic data, drag, trim, lift and static stability, damping, and static pressure are provided.

Report presenting an investigation in the 20-foot free-spinning tunnel to determine the erect and inverted spin and recovery characteristics of a 1/28-scale dynamic model of the North American FJ-4 airplane. Results indicated that either a flat-type or a steep-type spin maybe obtained when the airplane is spinning erect. Results regarding inverted spins, loading condition, spin-recovery rocket tests, and spin-recovery parachute tests are provided.

"An analysis was developed for calculating the radial temperature distribution in a gas turbine with only the temperatures of the gas and the cooling air and the surface heat-transfer coefficient known. This analysis was applied to determine the temperatures of a complete wheel of a conventional single-stage impulse exhaust-gas turbine. The temperatures were first calculated for the case of the turbine operating at design conditions of speed, gas flow, etc. and with only the customary cooling arising from exposure of the outer blade flange and one face of the rotor to the air" (p. 1).

A theoretical analysis of the radial temperature distribution through the rotor and constant cross sectional area blades near the coolant passages of liquid cooled gas turbines was made. The analysis was applied to obtain the rotor and blade temperatures of a specific turbine using a gas flow of 55 pounds per second, a coolant flow of 6.42 pounds per second, and an average coolant temperature of 200 degrees F. The effect of using kerosene, water, and ethylene glycol was determined. The effect of varying blade length and coolant passage lengths with water as the coolant was also determined. The effective gas temperature was varied from 2000 degrees to 5000 degrees F in each investigation.

"Computations were made to determine the temperature distribution and cooling of solid gas-turbine blades.A range of temperatures was used from 1500 degrees to 2500 degrees F, blade-root temperatures from 100 degrees to 1000 degrees F, blade thermal conductivity from 8 to 220 BTU/(hr)(sq ft)(degrees F/ft), and net gas to metal heat transfer coefficients from 75 to 250 BTU/(hr)(sq ft)(degrees F)" (p. 1).

A study was made of heat transfer in turbine blades and the effects on blade temperature of cooling the blade root and tip, changing the dimensions of the blades, raising the cycle temperatures, insulating with ceramics, and cooling by circulation of air or water through hollow blades. The results indicated that cooling of the root of the blade, shortening the blade, and cooling hollow blades internally with air or liquid offer possibilities of substantial increases in permissible gas temperatures.

From Summary: "A series of investigations of several 1/14-scale models of an inboard nacelle for the XB-36 airplane was made in the Langley two-dimensional low-turbulence tunnels. The purpose of these investigations was to develop a low-drag wing-nacelle pusher combination which incorporated an internal air-flow system. As a result of these investigations, a nacelle was developed which had external drag coefficients considerably lower than the original basic form with the external nacelle drag approximately one-half to two-thirds of those of conventional tractor designs. The largest reductions in drag resulted from sealing the gaps between the wing flaps and nacelle, reducing the thickness of the nacelle training-edge lip, and bringing the under-wing air inlet to the wing leading edge."

Memorandum presenting surveys of the impact pressure of the flow to obtain information for determining pressure losses in four different turbosupercharger nozzle boxes. The data indicated substantial differences in total head loss among the boxes and the existence of sharply defined high-loss regions in portions of the nozzle annulus.

"An experimental investigation has been made in the Langley stability tunnel at low speed to determine the static longitudinal and lateral stability characteristics of a 1/9-scale powered model of the Convair XFY-1 vertically rising airplane. Effects of thrust coefficient were investigated for the complete model and for certain components of the model. Effects of control deflections and of propeller-blade angle were investigated briefly for the complete model" (p. 1).

From Summary: "Incipient spin characteristics have been investigated on a 1/35-scale dynamic model of the Convair F-102A airplane. The model was launched by a catapult apparatus into free flight with various control settings, and the motions obtained were photographed. The model was ballasted for the combat loading. All tests were made with the speed brakes and landing gear retracted, and engine effects were not simulated."

"The method of Poggi is used to calculate, for perfect fluids, the effect of compressibility upon the flow on the surface of an elliptic cylinder at zero angle of attack and with no circulation. The result is expressed in a closed form and represents a rigorous determination of the velocity of the fluid at the surface of the obstacle insofar as the second approximation is concerned. Comparison is made with Hooker's treatment of the same problem according to the method of Janzen and Rayleight and it is found that, for thick elliptic cylinders, the two methods agree very well" (p. 245).

"This report presents some results obtained during an investigation to determine the effect of high inlet air temperature on the performance of a Liberty 12 aviation engine. The purpose of this investigation was to ascertain, for normal service carburetor adjustments and a fixed ignition advance, the relation between power and temperature for the range of carburetor air temperatures that may be encountered when supercharging to sea level pressure at altitudes of over 20,000 feet and without intercooling when using plain aviation gasoline and mixtures of benzol and gasoline" (p. 409).