Report discussing testing in the low-turbulence tunnel to determine the effectiveness of several configurations of vortex generators in increasing maximum lift of a 6-percent-thick symmetrical circular-arc airfoil section. None of the configurations tested were found to greatly increase the lift. Some of the configurations tested included a single row of vortex generators, two rows of generators, larger vortex generators, and sweeping forward the front row of generators.

Report presenting a free-flight investigation of a rocket-powered control research model to determine the force and hinge-moment characteristics of a half-delta tip control on a delta wing. Results regarding the control hinge moments, control normal force, and total normal force are provided.

Report presenting foredrag measurements made at zero angle of attack for a series of fineness ratio 3 nose shapes. The types of noses investigated included theoretically derived minimum drag shapes, hemispherically blunted cones, and other more common profiles. Results regarding hemispherically blunted cones, theoretical minimum drag nose shapes, and comparison of foredrag of all the force models are provided.

Report presenting investigations of the effects of fuel properties on combustion-chamber carbon deposition in singe tubular fuel-atomizing and fuel-prevaporizing combustors. The NACA K factor and the smoking tendency were approximately equally effective in relating carbon-deposition data from the prevaporizing and atomizing combustors. Results regarding the K factor, smoking tendency, effect of prevaporizing combustor operating conditions, sulfur, gum, and olefin, are provided.

"Supplementary blade-design data including rotor- and stator-blade coordinates and mean-line angles at the leading and the trailing edges are presented for a transonic axial-flow compressor inlet stage" (p. 1).

Report presenting an investigation of the planing characteristics of various combinations of a wheel and a hydro-ski. Models tested included at least two values of the following parameters: diameter of wheel, width of wheel, cross-section shape of wheel, fore-and-aft location of wheel, lateral location of wheel, gap between wheel and ski, rotation of wheel, and protrusion of wheel. Results regarding the general effect of a wheel, effect of wheel shape and size, effect of wheel-ski arrangement, and possible methods of reducing resistance are provided.

Report presenting the results of a series of qualitative studies with tufts on three wings with sweepback angles of 30 degrees, 45 degrees, and 60 degrees, which show that under certain conditions, a leading-edge vortex can exist in the unsteady flow associated with a gust. The results indicated that if a wing in steady flight prior to entering a gust is at an angle of attack several degrees less than that at which vortex flow first begins in steady flow, it may penetrate the gust without having the vortex develop, even if its angle of attack is increased by the gust into the vortex-flow regime.

From Introduction: "The results of this complete evaluation of the altitude performance and operational characteristics of the two types of flame-holder and fuel-system configurations are reported herein.The starting limits of both configurations at a flight Mach number of 0.6 are also discussed."

Report presenting an investigation of the effect of combustion on diffusion in the fuel preparation zone of a ram-jet engine. The information was applied in the design of combustor to operate at lean fuel-air ratios.

Report presenting an investigation of two versions of a type of forward underslung scoop mounted on a pointed fuselage in the supersonic blowdown tunnel. The scoop entrances were in the shape of a 60 degree sector of an annulus, but the sides of one scoop were sweptback, while the others were unswept. Results regarding the shadowgraphs and surface-pressure distributions and total-pressure recovery are provided.

Report presenting tests of rocket-propelled models at transonic speeds to compare the zero-lift drags of 45 degree sweptback wings with and without solid nacelles at the wing tips. The wing drag coefficient was lowered at high subsonic and supersonic speeds when the aspect ratio was reduced from 6.0 to 3.55. Results regarding the favorability of the wing-tip nacelles and the force-break Mach number of the varying configurations are also provided.

"The performance and operational characteristics of a Python turbine-propeller engine were investigated at simulated altitude conditions in the NACA Lewis altitude wind tunnel. In the performance phase, data were obtained over a range of engine speeds and exhaust nozzle areas at altitudes from 10,000 to 40,000 feet at a single cowl-inlet ram pressure ratio; independent control of engine speed and fuel flow was used to obtain a range of powers at each engine speed. Engine performance data obtained at a given altitude could not be used to predict performance accurately at other altitudes by use of the standard air pressure and temperature generalizing factors" (p. 1).

An investigation to determine the heat-shock resistant properties of two molybdenum disilicide turbine blades under centrifugal loads imposed by turbine rotation is presented. Molybdenum disilicide turbine blades fabricated by hot-pressing techniques withstood heat-shock conditions under blade centrifugal stresses up to 5350 pounds per square inch. Additional development is required before the heat-shock resistant properties of molybdenum disilicide are satisfactory for turbine-blade application.

A study investigated the effects of suction through porous leading-edge surfaces on the longitudinal aerodynamic characteristics of a 47.5 degree sweptback wing-fuselage configuration in the full-scale tunnel. The wing section normal to the quarter-chord line was NACA 64(sub 1)A112, the aspect ratio was 3.4, and the taper ratio was 0.51. Results regarding the basic wing characteristics and effect of area suction on the longitudinal characteristics are provided.

A study has been made of the variation of the distance separating bomb and aircraft with time after release as applied to dive-bombing operations, Separation distances determined from this study are presented in terms of two variables only, dive angle and maximum airplane accelerometer reading; the values of separation distance include the effects of delay in initiation of the pull-out and lag in attainment of the maximum normal acceleration. Contains analysis and calculations of the separation distances between bomb and dive bomber following bomb release; separation distances as determined by the dive angle and the maximum airplane accelerometer reading are presented in a single chart.

"An investigation was conducted in the Ames 12-foot pressure wind tunnel to determine the effect of an operating propeller on the aerodynamic characteristics of a 1/19-scale model of the Lockheed XFV-1 airplane. Several full-scale power conditions were simulated at Mach numbers from 0.50 to 0.92; the.Reynolds number was constant at 1.7 million. Lift, longitudinal force, pitch, roll, and yaw characteristics, determined with and without power, are presented for the complete model and for various combinations of model components" (p. 1).

An investigation of the effect of inlet pressure, corrected engine speed, and turbine temperature level on turbine-inlet gas temperature distributions was conducted on a J40-WE-6, interim J40-WE-6, and prototype J40-WE-8 turbojet engine in the altitude wind tunnel at the NACA Lewis laboratory. The engines were investigated over a range of simulated pressure altitudes from 15,000 to 55,000 feet, flight Mach numbers from 0.12 to 0.64, and corrected engine speeds from 7198 to 8026 rpm.