Report presenting tests of wing-fuselage combinations employing an airfoil-type fuselage in the variable-density wind tunnel as part of a wing-fuselage program. The models were designed to simulate an existing moderate-size transport airplane of that type. Results regarding some general comparisons, lift distribution and induced drag, and drag in high-speed flight are provided.

Report presenting a consideration of the general problem of stalling as affecting the safety of airplanes. The increased difficulties associated with modern efficient wings, particularly highly tapered wings and high-life devices, are discussed and means are considered for avoiding these difficulties.

Report presenting testing in the full-scale wind tunnel on a model of a large 4-engine monoplane to determine the overall aerodynamic efficiency of a conventional wing-nacelle-engine installation as compared with power-plant installations enclosed in the wing with extension shafts to the propellers. Results regarding power-on and power-off performance for the installations as well as propeller noise are provided.

Report presenting an investigation of the size and distribution of ice particles on the wings of aircraft and how they affect the aerodynamic characteristics. A simulated ice formation was generated from survey information received from aircraft pilots and was tested to determine the impact on the lift characteristics.

Report presenting a study of comparable information on full-scale spinning results and NACA free-spinning wind-tunnel results in order to determine the degree of reliability of tunnel results in predicting the spinning behavior of airplanes. Satisfactory agreement between model and airplane was found in 16 instances and disagreement was found in 5 instances.

Report presenting an experiment regarding tank and float venting conditions that exist on diving airplanes undergoing rapid changes in altitude. The results indicated that large pressure differences build up between the outside and inside of tanks and floats on diving airplanes unless the correct size of venting tube is used.

Report presenting tests made in the variable-density wind tunnel of airfoils of the NACA 4400 series modified by reflex at the trailing edge designed to reduce the pitching moment to the value of -0.03. The modified airfoils are designated the NACA 4400R series.

From Introduction: "This report presents the results of these tests which cover a total of about 70 flying hours on this airplane."

"Recent developments in airfoil-testing methods and fundamental air-flow investigations, as applied to airfoils, are discussed. Preliminary test results, obtained under conditions relatively free from stream turbulence and other disturbances, are presented. Suitable airfoils and airfoil-design principles were developed to take advantage of the unusually extensive laminar boundary layers that may be maintained under the improved testing conditions" (p. 1).

From Introduction: "An investigation has been conducted in the N.A.C.A. full-scale wind tunnel to determine the aerodynamic characteristics of a 1/4-scale model of a 4-engine monoplane when equipped with comparable air-cooled engine and liquid-cooled engine installations. The air-cooled engine installation consisted of nacelles equipped with N..A.C.A. cowlings and oil coolers located in the leading edge of the wing."

Report presenting tests conducted on a steel cylinder barrel with aluminum fins in order to determine the heat-transfer coefficients of the cylinder and the excellence of the bond between the steel barrel and the aluminum fins. Results regarding the heat-transfer tests and physical tests are provided.

Report presenting an investigation in the 20-foot wind tunnel to determine the drag, propulsive and net efficiencies, and cooling characteristics of several scale-model arrangements of air-cooled radial-engine nacelles and present-day propellers in front of an 18-percent-thick, 5-by-15-foot airfoil. Two 3-blade propellers with differing diameters were tested in conjunction with a 12-inch-diameter nacelle in three positions in front of the wing and with a 16-inch-diameter nacelle in six positions in front of the wing. Lift, drag, cooling-air flow, and propeller characteristics were determined for each arrangement.

Report presenting an investigation of the effects of propellers and of vibration on the extent of laminar flow on the NACA 27-212 airfoil by testing the airfoil in conjunction with a tractor and a pusher propeller and with a mechanical vibrator. The results show that neither the pusher propeller nor vibration with amplitudes up to 0.094 inch and with a frequency of 1650 cycles per minute had any consequential effect on the extent of laminar flow but that the tractor propeller had a very pronounced effect.

Report presenting flight and ground-cooling tests with a Northrop A-17A attack airplane to determine the merits of a nose-blower engine cowling designed and built at the NACA laboratory. The main objective was to determine the cooling characteristics of the nose blower, especially for ground and low-speed operation. Results regarding the cooling properties, engine pressure drop, and maximum speed and drag are provided.

Report presenting an investigation of the drag and power cost associated with the changing of the nose of a nacelle from a streamline shape to a conventional cowling shape. Full-scale propellers and nacelles were used. The results of the tests showed that the streamline afterbody drag approached that of an airship form and that the added drag due to the open-nose cowling was only a quarter of the drag increase obtained with the other afterbody.

Report presenting determinations of boundary-layer transition on the NACA 0012 and 23012 airfoils in the high-speed wind tunnel over a range of Reynolds numbers. For all of the lift coefficients that testing occurred at, transition occurred in the region of estimated laminar separation at low Reynolds numbers and approached the point of minimum static pressure as a forward limit at high Reynolds numbers.

Report presenting methods and charts for estimating the critical compressibility speeds of a large number of airfoils and streamline bodies. The systematic effects of thickness, thickness distribution, camber, camber location, leading-edge radius, and lift coefficient are considered. The results indicate that with a given lift coefficient, the thickness of the airfoil or of the body is the primary factor controlling its critical speed.

Report presenting an analysis and simple method to help solve the problem of assisting the take-off of an airplane by means of auxiliary jet propulsion by determining the jet thrust and weight of jet fuel required to provide a desired reduction in take-off distance or increase in pay load or fuel load for a fixed take-off distance. The use of previous experimental work to verify the analysis is also provided.

Report presenting an investigation to obtain data on the vertical and horizontal gusts in the atmosphere by reworking accelerometers and airspeed records from past investigations of vertical gusts. The results indicate that the vertical and horizontal gusts are of about equal intensity in the atmosphere.

Report presenting testing of a steel cylinder barrel with aluminum fins in order to evaluate the effect of using preformed aluminum fins on a steel barrel or aluminum barrel. Results regarding the heat-transfer tests and physical tests are provided.

"A unit injector was operated under various test conditions with a cam outline giving a high rate of plunger displacement. The rate of discharge of the unit injector followed the plunger displacement for the outwardly opening injection valve (open nozzle) except under conditions of high fuel pressures when the effect of fuel compressibility decreased the rate of discharge as the pressure increased. The rate of discharge for the inwardly opening injection valve (closed nozzle) did not directly follow the plunger displacement" (p. 1).

Report presenting testing of two engine cylinder barrels with aluminum fins. The primary purpose was to determine the heat-transfer coefficients and the excellence of the bonds between the aluminum fins and the aluminum base and between the aluminum base and the steel of the two barrels when manufactured by a large-volume production method.

Drag testing was conducted in the high-speed wind tunnel of 23 conditions combining six streamline shapes and three conventional cowling-fuselage bodies. All of the models were tested in combination with a wing in order to include wing-fuselage interference effects. The critical speeds of combinations tested were, in general, determined by the wing-fuselage juncture.

Report presenting a series of boundary-layer surveys over the surface of an NACA 0012 airfoil at zero lift. Results regarding the pressure distribution, laminar boundary layer, transition, turbulent boundary layer, drag, and skin friction are provided.