From abstract: "The variation of the reactivity of a pile as a function of width of a transverse gap is obtained. The method involves first finding the boundary condition satisfied by the flux at the gap face. This, in principle, provides enough information for a complete solution of the pile equations. A method for calculating the reactivity change is presented. The calculated reactivity is compared with experiment and a brief discussion of the validity of the approximations is given."

From summary: "The influence of the structure of phosphate esters on the distribution coefficient of uranium between solutions of these esters in carbon tetrachloride and aqueous nitrate solutions has been studied. Esters of secondary alcohols showed higher distribution coefficients than primary alcohols. Phenyl esters extracted less uranium than alkyl esters, and the presence of other negative groups also resulted in less extraction. Compounds containing carbon to phosphorus bonds gave higher distribution coefficients than the corresponding esters, and the distribution coefficients increased with the number of such carbon to phosphorus bonds. Tributyl phosphine oxide (with three carbon to phosphorus bonds) showed high distribution coefficients with many salts, including uranyl nitrate, uranyl sulfate, uranyl chloride, thorium nitrate, plutonium (IV) nitrate and some of the fission products in nitrate solution. It is planned to study these and similar compounds further."

From abstract: "On the 86-inch cyclotron a 41-kw beam has been calorimetered at a net ion loading efficiency of 40%; the average proton current was 1.85 ma at 22.5 Mev. Practical specific yields have been determined for (p,2n) reactions on zinc and bismuth. The investigation of products of proton-induced fission of uranium has been continued and new techniques are being used in measuring angular distribution of reaction products. The 63-inch heavy particle cyclotron is now in operation; N+++ particles have been accelerated to ~25 Mev. In preliminary tests, induced activities have been detected in carbon, nitrogen, and oxygen targets. A hot-cathode ion source is ready for test operation. The 22-inch cyclotron is being used in an investigation of the problems associated with the use of rf and dc electrodes for the acceleration of protons from the ion source into the dees. Radiation-induced corrosion in Inconel tubing containing #21 eutectic (ANP) has been produced by proton irradiation in the 86-inch cylclotron; it is shown that the corrosion was not due to thermal effects. Approximately 150 grams of highly purified U 238 (< 5 ppm U 235) have been prepared, and two grams of thorium 230 (ionium) has been enriched to 90.6%."

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, Price Daniel, regarding a legal question submitted for clarification: Occupation tax rate on liquid hydrocarbons recovered from gas by means of a separator, or other non-mechanical methods incidental to the production of gas.

Document issued by the Office of the Attorney General of Texas in Austin, Texas, providing an interpretation of Texas law. It provides the opinion of the Texas Attorney General, Price Daniel, regarding a legal question submitted for clarification: Legality of using County Permanent Improvement Funds to erect a livestock building at East Texas Fair grounds on land owned by the City of Tyler.

None

NpC and Pu{sub 2}O{sub 3} have been identified by x-ray diffraction. NpC is face-centered cubic, NaCl structure with a = 5.004 {+-} 0.005 A Pu{sub 2}O{sub 3} is isomorphous with the hexagonal ''A form'' for the rare earth sesquioxides with a = 3.840 {+-} 0.004 A; c = 5.957 {+-} 0.006 A and has essentially the same atomic parameters at La{sub 2}O{sub 3}. The lattice dimensions are smaller than predicted for pure Pu{sub 2}O{sub 3}, implying that the average oxidation number of plutonium is between (III) and (IV).

None

Memorandum presenting the pressure recovery, mass flow, and drag of a twin-scoop inlet-body combination measured at Mach numbers 1.4 and 1.7 at zero angle of attack. Tests were made of the inlet-body combination with an ogival forebody, an ogival forebody with a small amount of bluntness near the tip, and two forebodies of elliptical longitudinal section. Results regarding the effect of forebody bluntness on pressure recovery, effect of forebody bluntness on mass-flow ratio, and the effects of forebody bluntness on drag are provided.

Report presenting the low-speed longitudinal characteristics of swept wings derived from investigations at high Reynolds numbers. Two different types of flow separation, trialing-edge and leading-edge separation, are identified and discussed.

Report discusses the results of an updated investigation into the effectiveness of area suction when used to prevent air-flow separation at the leading edge of a 63 degree swept-back wing. This new report investigates the results of tests with chordwise distribution of the suction-air velocities controlled to give lower total-flow quantity requirements. The primary focus is the delay effected in air-flow separation and improvements made on aerodynamic characteristics of a wing with area suction specifically designed for a lift coefficient of 0.77.

"An investigation of the jet-spreading characteristics of a 16 inch ram-jet engine was conducted in the 8 by 6 foot supersonic tunnel at a Mach number of 2.0; both a converging nozzle having a contraction ratio of 0.71 and a cylindrical extension to the combustion chamber were used. The jet boundaries determined by means of pitot pressure surveys were compared with boundaries calculated from one-dimensional continuity and momentum relations. For the cylindrical nozzle, the jet reaches its maximum diameter, 4 percent greater than calculated, about 0.6 nozzle-exit diameter downstream of the nozzle exit" (p. 1).

Report presenting tests using the NACA wing-flow method to determine the effect of sweepback angle on the longitudinal characteristics of a scale semispan model of the Bell X-5 variable-sweep airplane at a range of Mach numbers. Lift, drag, and pitching moments were obtained for a range of angles of attack.

Report presenting an investigation to determine the effects of dual-rotation propeller operation at high thrust on the static longitudinal stability characteristics of a semispan powered model representing a twin-engine airplane configuration with flaps retracted. Stability and trim changes associated with an extreme constant power conditions were greatly dependent on tail height and vertical location of the center of gravity. Results regarding basic data, effects of power on overall stability and trim, and tuft-grid flow surveys are provided.

Memorandum presenting an investigation of a half-delta wing-tip control on a semispan 60 degree delta-wing-fuselage combination conducted in the 9- by 12-inch supersonic blowdown tunnel. Control-surface hinge moments and bending moments, as well as the characteristics of the complete wing-fuselage combination, were obtained over a large range of control deflection and angle of attack at specified Mach and Reynolds numbers. Results regarding the control bending-moment and hinge-moment characteristics, control effectiveness characteristics, and effect of fence on wing characteristics are provided.

Report presenting an investigation with the dual purpose of determining the effect of two bodies in various positions, symmetrically located from the plane of symmetry, on the aerodynamic characteristics of a wing-fuselage model and determining the aerodynamic loads on one of two bodies. Some of the most significant effects were obtained for the direct-mounted tip bodies which gave a large increase in the lift-curve slope of the basic model.

The outstanding oxidation resistance of molybdenum disilicide at 2400 F and above was found to depend on the formation of a protective siliceous coating which a-cristobalie has been identified. Molybdenum disilicide is not inherently resistant to oxidation and in powdered form burns at low temperatures.Melting and casting experiments have demonstrated the decomposition of the material at the melting point. The room-temperature modulus of elasticity has been determined and electric-resistivity data are given to 2000 F.

Report discussing some methods for predicting the carbon-forming propensity of turbojet-engine fuels from results of simple laboratory tests of the fuels. The prediction of carbon deposition from fuel characteristics including aromatic content, hydrogen-carbon ratio, distillation temperatures, gravity, and aniline point from several empirical laboratory carbon-deposition tests are provided. Results regarding fuel composition and volatility, related fuel properties, empirical laboratory tests, a comparison of methods predicting carbon-deposition characteristics of fuels, and application of fuel quality control methods are provided.

From Introduction: "The purpose of this report is to present the results of the investigation, to compare the coolant-flow requirements of the two configurations, and to show what advantages an air-cooled internal-strut-supported blade may have over an equivalent shell-supported air-cooled blade."

A full-scale J33 air-cooled split turbine rotor was designed and spin-pit tested to destruction. Stress analysis and spin-pit results indicated that the rotor in a J33 turbojet engine, however, showed that the rear disk of the rotor operated at temperatures substantially higher than the forward disk. An extension of the stress analysis to include the temperature difference between the two disks indicated that engine modifications are required to permit operation of the two disks at more nearly the same temperature level.

Report presenting flight tests to determine the pressure distribution over the wing of a swept-wing jet-propelled airplane over the flight range of lift coefficients for Mach numbers up to 1.11. Results regarding the section characteristics, load distribution, and trailing-edge loads are provided.

Report presenting an investigation to determine some of the basic problems and effects involved in a change of solidity accomplished by a change in the number of blades in an axial-flow-compressor rotor row and in a complete stage. Results regarding rotor performance and complete stage performance are provided.

"The modifications in the pressure distributions and the aerodynamic coefficients associated with additions of heat to the two-dimensional supersonic in viscid flow field adjacent to the lower surface of of a 5-percent-thickness symmetrical circular-arc wing are presented in this report. The pressure distributions are obtained by the use of graphical method which gives the two-dimensional supersonic inviscid flow field obtained with moderate heat addition. The variation is given of the lift-drag ratio and of the aerodynamic coefficients of lift, drag, and moment with free stream Mach number, angle of attack, and parameters defining extent and amount of heat addition" (p. 1).

Report presenting an investigation conducted with a conventional turbojet fuel, MIL-F-5624 (JP-3), and a low-volatility, high-density hydrocarbon, monomethylnaphthalene, in a vaporizing-type combustor to determine the combustion efficiency for variations in inlet-air conditions and fuel flow and to what extent fuel vaporization would minimize differences in combustion efficiency between the two fuels. Results regarding the performance of the combustor, correlation parameter, pressure-drop characteristics, and other miscellaneous observations are provided.