The Mesaverde Group of the Piceance Basin in western Colorado has been a pilot study area for government-sponsored tight gas sand research for over 20 years. This study provides a critical comparison of the geologic, production and reservoir characteristics of existing Mesaverde gas producing areas within the basin to those same characteristics at the MWX site near Rifle, Colorado. As will be discussed, the basin has been partitioned into three areas having similar geologic and production characteristics. Stimulation techniques have been reviewed for each partitioned area to determine the most effective stimulation technique currently used in the Mesaverde. This study emphasizes predominantly the southern Piceance Basin because of the much greater production and geologic data there. There may be Mesaverde gas production in northern areas but because of the lack of production and relatively few penetrations, the northern Piceance Basin was not included in the detailed parts of this study. 54 refs., 31 figs., 7 tabs.

The primary objective of the integrated system test phase is to demonstrate the commercial potential of a coal fueled diesel engine in its actual operating environment. The integrated system in this project is defined as a coal fueled diesel locomotive. This locomotive, shown on drawing 41D715542, is described in the separate Concept Design Report. The test locomotive will be converted from an existing oil fueled diesel locomotive in three stages, until it nearly emulates the concept locomotive. Design drawings of locomotive components (diesel engine, locomotive, flatcar, etc.) are included.

For the period March 1988 through February 1989, an estimated 154,558 angler-hours were expended to catch 20,037 rainbow trout, 3,933 smallmouth bass, and 14 bull trout. Estimated catch of other species, including cutthroat trout, whitefish, suckers, and squawfish totalled 84. Subcatchable rainbow trout (135 to 185mm) caught and released by boat anglers comprised 53% (12,770) of the total catch. An estimated 88.6% of the smallmouth bass caught were under the minimum legal size limit of 305mm and were released. Estimated harvest of smallmouth bass was 450. The highest monthly catch rate documented for all species excluding kokanee was 1.81 fish per hour during October. Severe weather conditions during February reduced effort and no fish were documented in the creel. Cumulative catch rates through the survey period for rainbow trout and smallmouth bass were .13 and .02, respectively. The lowest monthly catch rates generally occurred when fishing pressure was the highest, with fishing effort targeting on kokanee during the May through July high use periods. The Arlee strain rainbow trout was somewhat more vulnerable to boat anglers than the Shasta strain during the early post-release period. 20 refs., 16 figs., 12 tabs.

This note describes the diagnostics and auxiliary systems on the Microwave Tokamak Experiment (MTX) for confinement, transport, and other plasma physics studies. It is intended as a reference on the installed and planned hardware on the machine for those who need more familiarity with this equipment. Combined with the tokamak itself, these systems define the opportunities and capabilities for experiments in the MTX facility. We also illustrate how these instruments and equipment are to be used in carrying out the MTX Operations Plan. Near term goals for MTX are focussed on the absorption and heating by the microwave beam from the FEL, but the Plan also includes using the facility to study fundamental phenomena in the plasma, to control MHD activity, and to drive current noninductively.

Maywood Chemical Works (MCW) of Maywood, New Jersey, generated process wastes and residues associated with the production and refining of thorium and thorium compounds from monazite ores from 1916 to 1956. MCW supplied rare earth metals and thorium compounds to the Atomic Energy Commission and various other government agencies from the late 1940s to the mid-1950s. Area residents used the sandlike waste from this thorium extraction process mixed with tea and cocoa leaves as mulch in their yards. Some of these contaminated wastes were also eroded from the site into Lodi Brook. At the request of the US Department of Energy (DOE), a group from Oak Ridge National Laboratory conducts investigative radiological surveys of properties in the vicinity of MCW to determine whether a property is contaminated with radioactive residues, principally {sup 232}Th, derived from the MCW site. The survey typically includes direct measurement of gamma radiation levels and soil sampling for radionuclide analyses. The survey of this site, Kennedy Park, Money and Sidney Streets, Lodi, New Jersey (LJ062), was conducted during 1986 and 1987. Results of the survey demonstrated radionuclide concentrations in excess of the DOE Formerly Utilized Sites Remedial Action Program criteria. The radionuclide distributions are typical of …

The Radioactive Waste Management Complex (RWMC) Site Characterization Program is a continuation of the Subsurface Investigation Program (SIP). The scope of the SIP has broadened in response to the results of past work that identified hazardous as well as radionuclide contaminants in the subsurface environment and in response to the need to meet regulatory requirements. Two deep boreholes were cored at the RWMC during FY-1988. Selected sediment samples were submitted for Appendix IX of 40 CFR Part 264 and radionuclide analyses. Detailed geologic logging of archived core was initiated. Stratigraphic studies of the unsaturated zone were conducted. Studies to determine hydrologic properties of sediments and basalts were conducted. Geochemical studies and analyses were initiated to evaluate contaminant and radionuclide speciation and migration in the Subsurface Disposal Area (SDA) geochemical environment. Analyses of interbed sediments in boreholes D15 and 8801D did not confirm the presence of radionuclide contamination in the 240-ft interbed. Analyses of subsurface air and groundwater samples identified five volatile organic compounds of concern: carbon tetrachloride, trichloroethylene, 1,1,1-trichloroethane, chloroform, and tetrachloroethylene. 33 refs., 5 figs., 2 tabs.

The multiloop integral system test (MIST) was part of a multiphase program started in 1983 to address small-break loss-of-coolant accidents (SBLOCAs) specific to Babcock and Wilcox-designed plants. MIST was sponsored by the US Nuclear Regulatory Commission, the Babcock and Wilcox Owners Group, the Electric Power Research Institute, and Babcock and Wilcox. The unique features of the Babcock and Wilcox design, specifically the hot leg U-bends and steam generators, prevented the use of existing integral system data or existing integral system facilities to address the thermal-hydraulic SBLOCA questions. MIST and two other supporting facilities were specifically designed and constructed for this program, and an existing facility -- the once-through integral system (OTIS) -- was also used. Data from MIST and the other facilities will be used to benchmark the adequacy of system codes, such as RELAP5 and TRAC, for predicting abnormal plant transients. The individual tests are described in detail in Volumes 2 through 8 and Volume 11, and are summarized in Volume 1. Inter-group comparisons are addressed in this document, Volume 9. These comparisons are grouped as follows: mapping versus SBLOCA transients, SBLOCA, pump effects, and the effects of noncondensible gases. Appendix A provides an index and description of the …

Second neutron yields, energy spectra, and angular distributions have been measured at seven angles from 0 to 150{degree} for 113 and 256 MeV protons stopped in range-thick targets of aluminum and depleted uranium ({sup 238}U). Thin foil stacks of ten different materials were activated by secondary neutrons at distances of 20--30 cm from the targets. Following each irradiation, 30--40 different activation products were measured by gamma-ray spectroscopy. These activation rates were then used to adjust neutron energy spectra calculated by the HETC computer code. Activation cross sections were taken from ENDF/BV below 20 MeV, from literature values tested in Be(d,n) fields up to 50 MeV, and from proton spallation data and calculations from 50--250 MeV. Spectral adjustments were made with the STAY'SL computer code using a least-squares technique to minimize {chi}{sup 2} for a covariance matrix determined from uncertainties in the measured activities, cross sections, and calculated flux spectra. Neutron scattering effects were estimated from foil packets irradiated at different distances from the target. Proton effects were measured with (p,n) reactions. Systematic differences were found between the adjusted and calculated neutron spectra, namely, that HETC underpredicts the neutron flux at back angles by a factor of 2--3 and slightly overpredicts …

A financial data report for the Crystelle Waggoner Charitable Trust. The financial report details their assets by the year starting from 1984 to 1988 and the support grant they have awarded for that following year. In addition information, no deadline, has been circled.

A financial data report from the Anne Burnett and Charles D. Tandy Foundation for the tax year starting from 1984 to 1988. The data is tallied by how much assets the museum had at the end of the year and the amount they've awarded in grants.

A financial data report on the Helen Gertrude Sparks Charitable Trust. The financial report lists the foundations assets by year starting from 1984 to 1988 and list the supporting grants they have awarded for the years as well. In the additional information, no deadlines, has been circled.

We evaluate the conservation potential of compact fluorescent lamps (CFLs) for managing the rapidly increasing electrical energy and peak demand in India and Brazil. Using very conservative assumptions, we find that the cost of conserved energy using 16 W CFLs is 4 and 6 times less than the long range marginal cost of electricity for the two countries. The cost of avoided peak installed capacity is 6 and 9.5 times less than the cost of new installed capacity for India and Brazil. The analysis is undertaken from the three separate perspectives of the national economies, the consumers, and the utilities. We find that because residential electricity is subsidized, the consumers have little or no incentive to purchase and install the CFLs, unless they too are subsidized. However, the benefits of CFL installation to the utility are so large that subsidizing them is a paying proposition for the utility are so large that subsidizing them is a paying proposition for the utility in almost all cases. As an illustration of a gradual introduction strategy for CFLs, we calculate a scenario where national savings of the order of US $1.2 million per day for India and US $2.5 million per day for …

A financial data report for the Helen Irwin Littauer Educational Trust. The financial report lists the foundations assets by the years from 1984 to 1988 and the supporting grant they awarded for that year as well. In the additional information, deadline: must be submitted annually, has been underlined.

A financial data report on the Mary Potishman Lard Trust Agency. The financial report defines their assets from the 1984 year to the 1988 year along with the grant they have awarded for that year.

A financial data report for the Bass Foundation. The Bass Foundation awards grants to recipients as listed at the top, such are arts and higher education. The financial report lists the foundations assets from the 1984 year to the 1988 year and the grants awarded for that year.

A financial data report for Katrine Menzing Deakins Charitable Trust. The financial report goes into details about the foundations assets for the years 1984 to 1988 and the supporting grants that were award for that year. In additional information, deadline: June 30, has been circled.

This report is a technical evaluation of the final draft of the Fort St. Vrain (FSV) Upgraded Technical Specifications (UT/S) as issued by Public Service of Colorado (PSC) on May 27, 1988 with subsequent supplemental updates issued on June 15, 1988 and August 5, 1988. It has been compared for consistency, and safety conservatism with the Fort St. Vrain (FSV) Updated Final Safety Analysis Report (FSAR), the FSV Safety Evaluation Report (SER), the Facility Operating License, DPR-34, and all amendments to the Facility Operating License issued as of June 1, 1988, and Appendix A to the Operating License DPR-34, Technical Specifications. Because of the age of the plant, no supplements to the Fort St. Vrain SER have been issued since the original SER was not issued as a WASH or a NUREG report. This made it necessary to review all amendments to the Facility Operating License since they would contain the safety evaluations done to support changes to the Facility Operating License. The upgraded Fort St. Vrain Technical Specifications were also broadly compared with the latest Westinghouse Standard Technical Specifications (WSTS) to assure that what was proposed for Fort St. Vrain was consistent with the latest NRC staff practices for …

The electron beam in the XLS will collide with the residual gas in the vacuum chamber. The positive ions will be trapped in the potential well of the electron beam. They will perform stable or unstable oscillations around the beam under the repetitive Coulomb force of the bunches. If not cleared, the captured ions will lead to partial or total neutralization of the beam, causing both, a decrease of life-time and a change in the vertical tunes as well as an increase in the tune-spread. They can also cause coherent transverse instabilities. The degree of neutralization {theta} that one can tolerate, is primarily determined by the allowable tune shift, which of the XLS is between 1 and 5 10{sup {minus}3}. Electrostatic clearing electrodes will be used to keep the neutralization below the desired limit. In order to determine their location and the necessary clearing-rate and voltage, we examine the ion production rate, longitudinal velocity of ions in field-free regions and in the dipoles to see what distance the ions can travel without clearing before the neutralization of the beam reaches the prescribed limit, beam potential to see the locations of the potential wells, voltage requirements for ion clearing, critical mass …

The extensions of the physics and engineering guidelines for the ITER device needed for acceptable operating points for a steady-state tokamak power reactor are examined. Non-inductive current drive is provided in steady state by high-energy neutral-beam injection in the plasma core, lower-hybrid slow waves in the outer regions of the plasma and (30%) bootstrap current. Three different levels of extension of the ITER physics/engineering guide-lines, with differing assumptions on the possible plasma beta, elongation and aspect ratio, are considered for power-reactor applications. Plasma gain, Q/sub p/ = fusion power/input power, in excess of 20 and average neutron wall fluxes from 2.3 to 3.6 MW/m/sup 2/ are predicted in devices with major radii varying from 7.0 to 6.0 m and aspect ratios from 2.9 to 4. 3. Peak divertor heat fluxes range up to 12.2 MW/m/sup 2/ which is somewhat higher than the current ITER design limit of 10 MW/m/sup 2/ with a magnetically swept divertor. These designs were selected on the basis of improvements in physics/engineering consistent with time scales for development of future reactors. The design re-optimization on the basis of cost-of-electricity (COE) was then examined using a reactor systems model. This analysis generally verified the original estimates for …

Maywood Chemical Works (MCW) of Maywood, New Jersey, generated process wastes and residues associated with the production and refining of thorium and thorium compounds from monazite ores from 1916 to 1956. MCW supplied rare earth metals and thorium compounds to the Atomic Energy Commission and various other government agencies from the late 1940s to the mid-1950s. Area residents used the sandlike waste from this thorium extraction process mixed with tea and cocoa leaves as mulch in their yards. Some of these contaminated wastes were also eroded from the site into Lodi Brook. At the request of the US Department of Energy (DOE), a group from Oak Ridge National Laboratory conducts investigative radiological surveys of properties in the vicinity of MCW to determine whether a property is contaminated with radioactive residues, principally {sup 232}Th, derived from the MCW site. The survey typically includes direct measurement of gamma radiation levels and soil sampling for radionuclide analyses. The survey of this site, 106 Columbia Lane, Lodi, New Jersey (LJ063), was conducted during 1987. Results of the survey demonstrated radionuclide concentrations in excess of the DOE Formerly Utilized Sites Remedial Action Program criteria. The radionuclide distributions are typical of the type of material originating …

This report on urban ozone was requested by the Senate Committee on Environment and Public Works, the House Committee on Energy and Commerce, and its Subcommittee on Health and the Environment in anticipation of the upcoming reauthorization of the Clean Air Act. Of the air pollutants that the Act covers, ozone has been the most difficult to bring under control; it may well be the most expensive.

This background paper reviews the status of the major sectors of the maritime industry engaged in EEZ activities and notes the significant trends. Basic data on the major sectors were first prepared for OTA by the Maritime Administration. OTA then conducted a survey of industry and other interested parties and prepared the analyses in the paper.

This paper examines dichotomous designations used to define rural and urban areas and discusses how they are applied in certain Federal programs. In addition, several topologies are described that are useful in showing the diversity that exists within rural areas.

During the report period, work continued on the life-cycle testing, optimization and refining of the second-generation furnace assembly, which comprises all the major furnace components: The combustor, heat exchanger, and baghouse, as well as the auxiliary subsystems. The furnace has operated for about 90 hours, and has burned 1,000 pounds of CWS. During testing, the only maintenance that was performed on the system was to clean the bag filters to obtain ash samples for analysts. Concurrent with testing the second-generation furnace, fabrication and assembly of the third-generation furnace was completed, and a life-cycle testing and optimization process for this furnace has started. In contrast to the second-generation furnace, which was designed more as an experimental unit, the third-generation furnace is a stand-alone heating unit Incorporating the standard air handling system, blower, pump, and control box as part of the furnace. During the report period, the third-generation furnace operated for a total of 35 hours, and burned more than 300 pounds of CWS, with average tests lasting 6 hours. During the next quarter, life-cycle testing of the third-generation furnace will continue to identify areas needing further development.