Circular presenting a description of the Boulton Paul P.71A, which is a new type of two-engine biplane. Details of the design, fuel tanks, materials, fuselage, passenger seating, tail, and flying qualities are provided.

"This thesis presents the method of moment distribution modified to include the effect of axial load upon the bending moments. This modification makes it possible to analyze accurately complex structures, such as rigid fuselage trusses, that heretofore had to be analyzed by approximate formulas and empirical rules. The method is simple enough to be practicable even for complex structures, and it gives a means of analysis for continuous beams that is simpler than the extended three-moment equation now in common use" (p. 1).

Report issued by the U.S. Bureau of Mines on the measuring of temperature and pressure in oil and gas wells. Descriptions of the instrumentation developed and used for these measurements are presented. This report includes tables, graphs, and illustrations.

Report issued by the U.S. Bureau of Mines on the issues of disposal of crude oil and natural gas brine. Disposal methods are studied and presented. This report includes tables, maps, and illustrations.

Report discussing earthquake activity in the United States during 1935. The report is broken down by regions and has sections for specific earthquakes.

"A method is presented for calculating the aerodynamic forces on a moncylane wing, taking into account the elastic twisting of the wing due to these forces. The lift distribution along the span is calculated by the formulas of Amstutz as a function of the geometrical characteristics of the wing and of the twist at stations 60 and 90 percent of the semispan. The twist for a given lift distribution is calculated by means of influence lines" (p. 1).

"This report gives the characteristics of a wing with an auxiliary airfoil mounted near its trailing edge and used as a flap. The tests were made with a 10 by 60 inch Clark Y main airfoil and an NACA 0012 flap having a chord equal to 15 percent of the main wing chord. The axis of the flap in all cases was on the flap chord and 20 percent back from its leading edge. The optimum location of the flap axis relative to the main wing for maximum lift was found to be 1.25 percent of the main wing chord behind the trailing edge and 2.5 percent below the chord" (p. 1).

Oxygen regulators are used in aircraft to regulate automatically the flow of oxygen to the pilot from a cylinder at pressures ranging up to 150 atmospheres. The instruments are adjusted to open at an altitude of about 15,000 ft. and thereafter to deliver oxygen at a rate which increases with the altitude. The instruments are tested to determine the rate of flow of oxygen delivered at various altitudes and to detect any mechanical defects which may exist.

Report presenting an examination of the thermodynamics of combustion in the Otto cycle engine, including the effects of turbulence and some of the possible causes of detonation within an engine.

"NACA model 11-C was tested with four different depths of step to obtain information as to the effect of the depth of step on the water performance. The depths of step were selected to cover the practicable range of depths and in each case the included angle between the forebody and afterbody keels was kept the same 6-1/2 degrees. Small depths of step were found to give lower resistance at speeds below and at the hump speed of the model and greater depths of step lower resistance at high speeds" (p. 1).

"Rules and methods for insuring safe structural strength of racing airplanes used in the major air meets in this country have recently been considered. Acceleration records made in racing airplanes during actual air races were therefore considered desirable, and the NACA undertook the measurement of acceleration of loads on airplanes during all conditions of flight. Accelerations were measured on four airplanes at the Miami All-American Races in January 1934 and January 1935" (p. 1).

The results of a general tank test model 11-C, a conventional pointed afterbody type of flying-boat hull, are given in tables and curves. These results are compared with the results of tests on model 11-A, from which model 11-C was derived, and it is found that the resistance of model 11-C is somewhat greater. The effect of changing the plan form of the step on model 11-C is shown from the results of tests made with three swallow-tail and three pointed steps formed by altering the original step of the model. These results show only minor differences from the results obtained with the original model.

In this paper there is presented a deflection formula for single-span beams of constant section subjected to combined axial and transverse loads of the types commonly encountered in airplane design. The form of the equation is obtainable by dimensional analysis. Tables and curves of the non dimensional coefficients are appended to facilitate the use of the formula. The equation is applied to the determination of the spring constant of a beam. Tables and curves are presented to show the variation of the spring constant with changes in the axial load and position along the beam.

NACA model 11-C was tested according to the general method with the angle of afterbody keel set at five different angles from 2-1/2 degrees to 9 degrees, but without changing other features of the hull. The results of the tests are expressed in curves of test data and of non-dimensional coefficients. At the depth of step used in the tests, 3.3 percent beam, the smaller angles of afterbody keel give greater load-resistance ratios at the hump speed and smaller at high speed than the larger angles of afterbody keel. Comparisons are made of the load-resistance ratios at several other points in the speed range. The effect of variation of the angle of afterbody keel upon the take-off performance of a hypothetical flying boat of 15,000 pounds gross weight having a hull of model 11-C lines is calculated, and the calculations show that the craft with the largest of the angles of afterbody keel tested, 9 degrees, takes off in the least time and distance.

"A method of calculating the stresses and torsional stiffness of thin shells with interior webs is summarized. Comparisons between experimental and calculated results are given for 3 duralumin beams, 5 stainless steel beams and 2 duralumin wings. It is concluded that if the theoretical stiffness is multiplied by a correction factor of 0.9, experimental values may be expected to check calculated values within about 10 percent" (p. 1).

"Simultaneous air-flow photographs and pressure-distribution measurements have been made of the NACA 4412 airfoil at high speeds in order to determine the physical nature of the compressibility bubble. The flow photographs were obtained by the Schlieren method and the pressures were simultaneously measured for 54 stations on the 5-inch-chord wing by means of a multiple-tube photographic manometer. Pressure-measurement results and typical Schlieren photographs are presented" (p. 1).

"This report is the fourth of a series presenting the results of strength tests on thin-walled cylinders and truncated cones of circular and elliptic section; it includes the results on 100 thin-walled Duralumin cylinders of circular section with ends clamped to rigid bulkheads. The tests show that as the ratio of moment to shear varies from small to large values the failure changes from a shear to a bending type. In the report a chart is presented that shows the corresponding changes in strength" (p. 1).

"The main purpose of this investigation is to make available to the designer useful information with regard to the aerodynamic drag of various types of flying-boat hull models. The present report is the first in a series covering investigation in this field. Through close cooperation between hydrodynamics and aerodynamics divisions it is hoped that results leading to improvements in hull design obtained" (p. 1).

General methods of theoretical analysis of airplane spinning characteristics have been available for some time. Some of these methods of analysis might be used by designers to predict the spinning characteristics of proposed airplane designs if the necessary aerodynamic data were known. The present investigation, to determine the spinning characteristics of wings, is planned to include variations in airfoil sections, plan forms, and tip shapes of monoplane wings and variations in stagger, gap, and decalage for biplane cellules.

This report is the fifth of a series presenting the results of strength tests of thin-walled cylinders and truncated cones of circular and elliptic section; it includes the results obtained from torsion tests on 30 cylinders, pure bending tests on 30 cylinders, and combined transverse shear and bending tests on 60 cylinders. All the cylinders tested were elliptic section with the ends clamped to rigid bulkheads. In the pure bending and combined transverse shear and bending tests the loads were applied in the plane of the major axis. The results of the tests on elliptic cylinders are correlated with the results of corresponding tests on circular cylinders and are presented in charts suitable for use in design.

During an extensive study of all types of rotating wings, the NACA examined the cyclogiro rotor and made an aerodynamic analysis of that system (reference 1). The examination disclosed that such a machine had sufficient promise to justify an experimental investigation; a model with a diameter and span of 8 feet was therefore constructed and tested in the 20-foot wind tunnel during 1934. The experimental work included tests of the effect of the motion upon the rotor forces during the static-lift and forward-flight conditions at several rotor speeds and the determination of the relations between the forces generated by the rotor and the power required by it.

Report presenting an analysis of a wing brace with a small auxiliary strut, which is attached to the wing spar at the upper end. The design is quite effective but has some difficult analysis problems. The report is broken into two parts; one is a theoretical investigation and one is an experimental investigation.

"The paper beings with a brief discussion on the origin of the bending stresses in cantilever box beams under torsion. A critical survey of existing theory is followed by a summary of design formulas; this summary is based on the most complete solution published but omits all refinements considered unnecessary at the present state of development. Strain-gage tests made by NACA to obtained some experimental verification of the formulas are described next. Finally, the formulas are applied to a series of box beams previously static-tested by the U.S. Army Air Corps; the results show that the bending stresses due to torsion are responsible to a large extent for the free-edge type of failure frequently experienced in these tests" (p. 1).

"The NACA model 11-G flying-boat hull, a modification of NACA model 11-A was tested over a range of loadings. The planing bottom of model 11-G has a variable-radius flare, or concavity, at the chines in contrast to the straight V planing bottom of model 11-A. The results are given as curves of resistance and trimming moment plotted against speed for various angles of trim" (p. 1).