This study was initiated in 1957 by the U.S. Public Health and many facets of this project are reaching final objectives. Many new studies have developed in the course of this study and will continue. The projects supported by the Energy Research and Development Administration are of utmost importance and consist of: collection of material from uranium miners known to have cancer of the lung into a tumor registry; manual on pulmonary cytology; regression study of sputum cytological findings in uranium miners who showed marked atypical squamous cell metaplasia and have quit smoking cigarettes, mining, or both; continuation of sputum collection and collection of lungs from deceased miners; sensory development for localization of carcinoma in situ of the lung; and lung histology program. Since we have examined approximately 77,000 sputum samples over the last 20 years in cases that showed normal cytology at the inception of the study and some subsequently developed carcinoma of the lung, we have an accumulation of material that is worthy of study and presentation.

Ground water pumping tests were performed in two wells located in the foothills east of Idaho Falls to determine the aquifer characteristics at these locations. These data were used to differentiate this aquifer from the Snake River Plain aquifer. The wells were pumped at rates of 11 and 14 gallons per minute with 0.03 and 0.04 ft of drawdown measured in the pumping wells. The transmissivity is estimated to be 525,000 gpd/ft and 450,000 gpd/ft, respectively. The hydraulic conductivity is 925 ft/day and 1,070 ft/day, respectively. These hydraulic conductivities are similar to those measured in the Snake River Plain aquifer. Water level data in these wells are consistent with the water table in the Snake River Plain aquifer and indicates ground water movement from the foothills toward the Plain. The high transmissivity suggests water may move rapidly from the foothills area to mix with water in the Snake River Plain aquifer. Elevated water temperatures (76 and 70{degrees}F) and high specific conductivities in these wells indicate the presence of a foothills aquifer with characteristics that can be used to separate the two aquifer systems.

A letter report issued by the Government Accountability Office with an abstract that begins "In 2007, the Department of the Interior (Interior) collected about $10.5 billion in revenues from companies that hold federal oil and gas leases. Interior's Minerals Management Service manages offshore leases, while its Bureau of Land Management manages onshore leases and leases in the National Petroleum Reserve in Alaska. Acquiring a federal lease gives the lessee the rights to explore for and develop the oil and gas resources under the lease. Development entails many tasks, including drilling wells and building pipelines that may lead to oil and gas production. GAO agreed to (1)describe Interior's efforts to encourage development of federal oil and gas leases and compare them to states' and private landowners' efforts, (2)examine trends in leasing and factors that may affect development, and (3) describe development on a sample of leases. GAO reviewed data on about 55,000 leases and spoke to officials at Interior and in eight states with leasing experience, among others."

A letter report issued by the Government Accountability Office with an abstract that begins "Fatalities on U.S. roads now total over 40,000 each year. Future reductions may require the Department of Transportation (DOT) to address new trends such as evolving crash-avoidance technologies and rapidly changing electronic devices that may distract drivers who use them on the road. (See figure.) GAO was asked to examine how DOT is addressing fast-moving trends such as these. This report examines how DOT is (1) deciding on responses to the crash avoidance and electronic distractions trends--given available evidence and uncertainties; (2) developing new evidence on these trends' safety impacts; and (3) communicating with the Congress about these and other trends and related issues. To conduct this study, GAO analyzed DOT reports, peer-reviewed literature, and other documents; interviewed DOT officials and staff; and interviewed over 30 experts."

A letter report issued by the Government Accountability Office with an abstract that begins "The Social Security Act requires that the Social Security Administration (SSA) find an improvement in a beneficiary's medical condition in order to remove him or her from either the Disability Insurance (DI) or Supplemental Security Income (SSI) programs. GAO was asked to (1) examine the proportion of beneficiaries who have improved medically and (2) determine if factors associated with the standard pose challenges for SSA when determining whether beneficiaries continue to be eligible for benefits. To answer these questions, GAO surveyed all 55 Disability Determination Services (DDS) directors, interviewed SSA officials, and reviewed pertinent SSA data."

A letter report issued by the Government Accountability Office with an abstract that begins "More than 5.5 billion pounds of explosives are used each year in the United States by private sector companies and government entities. The Bureau of Alcohol, Tobacco, Firearms and Explosives (ATF) has authority to regulate explosives and to license privately owned explosives storage facilities. After the July 2004 theft of several hundred pounds of explosives from a state and local government storage facility, concerns arose about vulnerability to theft. GAO analyzed (1) the extent of explosives thefts from state and local government facilities, (2) ATF's authority to regulate and oversee state and local government explosives storage facilities, (3) the information ATF collects about state and local government storage facilities, and (4) security oversight measures in place at selected state and local government storage facilities."

A letter report issued by the Government Accountability Office with an abstract that begins "Reducing the incidence of sexually transmitted diseases and unintended pregnancies is one objective of the Department of Health and Human Services (HHS). HHS provides funding to states and organizations that provide abstinence-until-marriage education as one approach to address this objective. GAO was asked to describe the oversight of federally funded abstinence-until-marriage education programs. GAO is reporting on (1) efforts by HHS and states to assess the scientific accuracy of materials used in these programs and (2) efforts by HHS, states, and researchers to assess the effectiveness of these programs. GAO reviewed documents and interviewed HHS officials in the Administration for Children and Families (ACF) and the Office of Population Affairs (OPA) that award grants for these programs."

This report was submitted to the American Society for Information Science and Technology (ASIS&T) Board of Directors. In June 2011, an ASIS&T Task Force on Webinars was appointed. This is the final report discusses the findings of this task force and recommendations.

A staff paper by the Office of Technology Assessment (OTA) assessing the workplace reproductive health hazards regulations.

This annual report is a deliverable for fiscal year 2006 (FY06) for Project 2002-077-00, Facilitation of the Estuary/Ocean Subgroup (EOS). The EOS is part of the research, monitoring, and evaluation (RME) effort the Action Agencies (Bonneville Power Administration, U.S. Army Corps of Engineers, U.S. Bureau of Reclamation) developed in response to the 2000 and 2004 Biological Opinions on operation of the Federal Columbia River Power System. The goal of the EOS project is to facilitate activities of the estuary/ocean RME subgroup as it coordinates implementation of the Estuary RME Plan. In FY06, EOS project accomplishments included: 1) subgroup meetings; 2) participation in the estuary work group of the Pacific Northwest Aquatic Monitoring Partnership; 3) project management via the project tracking system, PISCES; 4) quarterly project status reports; and 5) a major revision to the Estuary RME Plan (new version May 2006) based on comments by EOS members, the Independent Scientific Review Panel, and other reviewers. In the context of uncertainty about the direction of the federal RME due to litigation on the FCRPS Biological Opinion, FY06 activities for the EOS project resulted in expanded substantive coordination with other regional RME forums, project tracking infrastructure, and a new version of the …

The ASME Boiler and Pressure Vessel Code provides rules for the construction of nuclear power plant components. The Code specifies fatigue design curves for structural materials. However, the effects of light water reactor (LWR) coolant environments are not explicitly addressed by the Code design curves. Existing fatigue strain-vs.-life ({var_epsilon}-N) data illustrate potentially significant effects of LWR coolant environments on the fatigue resistance of pressure vessel and piping steels. This report provides an overview of the existing fatigue {var_epsilon}-N data for carbon and low-alloy steels and wrought and cast austenitic SSs to define the effects of key material, loading, and environmental parameters on the fatigue lives of the steels. Experimental data are presented on the effects of surface roughness on the fatigue life of these steels in air and LWR environments. Statistical models are presented for estimating the fatigue {var_epsilon}-N curves as a function of the material, loading, and environmental parameters. Two methods for incorporating environmental effects into the ASME Code fatigue evaluations are discussed. Data available in the literature have been reviewed to evaluate the conservatism in the existing ASME Code fatigue evaluations. A critical review of the margins for ASME Code fatigue design curves is presented.

This Calculation Note performs and documents MCNP criticality calculations for plutonium (100% {sup 239}Pu) hydraulic fluid mixtures. Spherical geometry was used for these generalized criticality safety calculations and three geometries of neutron reflection are: {sm_bullet}bare, {sm_bullet}1 inch of hydraulic fluid, or {sm_bullet}12 inches of hydraulic fluid. This document shows the critical volume and critical mass for various concentrations of plutonium in hydraulic fluid. Between 1 and 2 gallons of hydraulic fluid were discovered in the bottom of HA-23S. This HA-23S hydraulic fluid was reported by engineering to be Fyrquel 220. The hydraulic fluid in GLovebox HA-23S is Fyrquel 220 which contains phosphorus. Critical spherical geometry in air is calculated with 0 in., 1 in., or 12 inches hydraulic fluid reflection.

Savannah River National Laboratory (SRNL) was requested to provide the Defense Waste Processing Facility (DWPF) with a frit composition for Sludge Batch 5 (SB5) to optimize processing. A series of experiments were designed for testing in the Melt Rate Furnace (MRF). This dry fed tool can be used to quickly determine relative melt rates for a large number of candidate frit compositions and lead to a selection for further testing. Simulated Sludge Receipt and Adjustment Tank (SRAT) product was made according to the most recent SB5 sludge projections and a series of tests were conducted with frits that covered a range of boron and alkali ratios. Several frits with relatively large projected operating windows indicated melt rates that would not severely impact production. As seen with previous MRF testing, increasing the boron concentration had positive impacts on melt rate on the SB5 system. However, there appears to be maximum values for both boron and sodium above which the there is a negative effect on melt rate. Based on these data and compositional trends, Frit 418 and a specially designed frit (Frit 550) have been selected for additional melt rate testing. Frit 418 and Frit 550 will be run in the …

We have developed a research program dedicated to the quantitative laboratory study of turbulent convection.

A Joint Interagency Working Group (JIWG) under the auspices of the Department of Homeland Security Office of Research and Development conducted a technology assessment of emergency radiological dose assessment capabilities as part of the overall need for rapid emergency medical response in the event of a radiological terrorist event in the United States. The goal of the evaluation is to identify gaps and recommend general research and development needs to better prepare the Country for mitigating the effects of such an event. Given the capabilities and roles for responding to a radiological event extend across many agencies, a consensus of gaps and suggested development plans was a major goal of this evaluation and road-mapping effort. The working group consisted of experts representing the Departments of Homeland Security, Health and Human Services (Centers for Disease Control and the National Institutes of Health), Food and Drug Administration, Department of Defense and the Department of Energy's National Laboratories (see appendix A for participants). The specific goals of this Technology Assessment and Roadmap were to: (1) Describe the general context for deployment of emergency radiation dose assessment tools following terrorist use of a radiological or nuclear device; (2) Assess current and emerging dose assessment …

Simulations of mode I interlaminar fracture toughness tests of a carbon-reinforced composite material (BMS 8-212) were conducted with LSDYNA. The fracture toughness tests were performed by U.C. Berkeley. The simulations were performed to investigate the validity and practicality of employing decohesive elements to represent interlaminar bond failures that are prevalent in carbon-fiber composite structure penetration events. The simulations employed a decohesive element formulation that was verified on a simple two element model before being employed to perform the full model simulations. Care was required during the simulations to ensure that the explicit time integration of LSDYNA duplicate the near steady-state testing conditions. In general, this study validated the use of employing decohesive elements to represent the interlaminar bond failures seen in carbon-fiber composite structures, but the practicality of employing the elements to represent the bond failures seen in carbon-fiber composite structures during penetration events was not established.

The focus of our work during the duration of this grant was on the following areas: (a) the fundamental plasma physics of intense laser-plasma interactions, including the nonlinear excitation of plasma waves for accelerator applications, as well as the recently discovered by us phenomenon of the relativistic bi-stability of relativistic plasma waves driven by a laser beatwave; (b) interaction of high power microwave beams with magnetized plasma, including some of the recently discovered by us phenomena such as the Undulator Induced Transparency (UIT) as well as the new approaches to dynamic manipulation of microwave pulses; (c) investigations of the multi-color laser pulse interactions in the plasma, including the recently discovered by us phenomenon of Electromagnetic Cascading (EC) and the effect of the EC of three-dimensional dynamics of laser pulses (enhanced/suppressed selffocusing etc.); (d) interaction of high-current electron beams with the ambient plasma in the context of Fast Ignitor (FI) physics, with the emphasis on the nonlinear dynamics of the Weibel instability and beam filamentation.

The Defense Waste Processing Facility (DWPF) will transition from Sludge Batch 4 (SB4) processing to Sludge Batch 5 (SB5) processing in early fiscal year 2009. Tests were conducted using non-radioactive simulants of the expected SB5 composition to determine the impact of varying the acid stoichiometry during the Sludge Receipt and Adjustment Tank (SRAT) and Slurry Mix Evaporator (SME) processes. The work was conducted to meet the Technical Task Request (TTR) HLW/DWPF/TTR-2007-0007, Rev. 1 and followed the guidelines of a Task Technical and Quality Assurance Plan (TT&QAP). The flowsheet studies are performed to evaluate the potential chemical processing issues, hydrogen generation rates, and process slurry rheological properties as a function of acid stoichiometry. Initial SB5 flowsheet studies were conducted to guide decisions during the sludge batch preparation process. These studies were conducted with the estimated SB5 composition at the time of the study. The composition has changed slightly since these studies were completed due to changes in the washing plan to prepare SB5 and the estimated SB4 heel mass. Nine DWPF process simulations were completed in 4-L laboratory-scale equipment using both a batch simulant (Tank 51 simulant after washing is complete) and a blend simulant (Tank 40 simulant after Tank 51 …

Level population as a function of laser pulse envelope area for an atom which could be approximated as a two level system was measured. An ideal two-level system under the action of an oscillating force is one of a few quantum mechanical systems for which the time-dependent Schroedinger equation can be solved exactly. The solution predicts that the population of the upper state, for a system which was entirely in the lower state at t = 0, varies as sin/sup 2/A, where A = ..integral../sub 0//sup t/ ..cap omega..(t) dt, and ..cap omega.. = e epsilon/sub 0/(t) x/sub 12//h-bar.

Enclosed in this report are plots of the wave generating ship tracks and velocities for the West Coast Scotland Experiment (WCSEX) 1991.

Results of a study to determine the limiting temperature conditions in a large reactor system are presented. The study considers a sodium-cooled breeder reactor system having a loop-type primary system configuration. A temperature range of 930 to 1050/sup 0/F in reactor outlet temperature is covered. Significant findings were that the use of the materials for the 930/sup 0/F reference design, i.e., a core material of 20% cold-worked 316 stainless steel, a primary piping material of 316SS, and a steam generator material of unstabilized 2-1/4 Cr - 1 Mo resulted in limiting conditions in component performance at the higher temperatures. Means to circumvent these limits through the use of alternate materials, mitigation of thermal transients, and/or design changes are presented. The economic incentive to make some materials changes is also presented.

It is shown that the use of octopole stabilization in a tandem mirror allows a large reduction in end-cell length. A novel feature of the method proposed in this report is the placement of the minimum IBI region coonsiderably off axis, thus rendering the core plasma more axisymmetric. The region from the core to the field minimum is bridged by a mirror-confined hot-electron mantle. Low ..beta.., ideal magnetohydrodynamic stability, as evaluated with the interchange criterion, yields an upper limit to the required mantle peak ..beta.. of 78% for a center-cell peak ..beta.. of 75% and barrier peak ..beta.. of 30%. Estimates for the worst type of classical radial diffusion - with stochastic displacements per bounce - show that such radial losses are negligible for this configuration. First estimates of power balance indicate Q approx. 10 for a reactor producing 500 MW of fusion power and Q approx. 25 for one producing 1000 MW, using conservative assumptions regarding mantle ..beta.. requirements and synchrotron radiation losses.

Memorandum presenting an analysis of probable heat-exchanger weights for stationary and rotary regenerator heat exchangers for use in a hydrogen-expansion turbine engine. This is because rotary regenerators offer possibilities for a considerably lighter heat-exchanger core, possibly one-fourth that of the stationary regenerators.

In accelerator theory of particle longitudinal motion, a classical definition if a synchronous particle (synchronous energy, synchronous phase, synchronous orbit) assumes that there is a one-to-one relationship of the accelerator electrical field. In practice, that relationship may not be sustained because of errors in the magnetic field, radio frequency, or because sometimes we do not want to keep that relationship for some reason. In this report we formulate the concept of adiabatic equilibrium between particle and accelerator, and we introduce a definition of synchronous particle when the magnetic field and radio frequency are independent functions of time. The result is that size and shape of the bucket (separatrix) depends not only on the fields rate of change /dot B/, but on the frequency rate /dot f/ as well. This means, for example, we can have a stationary bucket even at the rising field /dot B/ > 0. Having a frequency f in addition to field B and voltage V as parameters controlling the bucket dynamics, we will show how to decrease particle losses during injection and capture. 6 refs., 7 figs.