"In order to determine the effect of the surface conditions of a wing on the aerodynamic characteristics of an airplane, tests were conducted in the N.A.C.A. full-scale wind tunnel on the Fairchild F-22 airplane first with normal commercial finish of wing surface and later with the same wing polished. Comparison of the characteristics of the airplane with the two surface conditions shows that the polish caused a negligible change in the lift curve, but reduced the minimum drag coefficient by 0.001. This reduction in drag if applied to an airplane with a given speed of 200 miles per hour and a minimum drag coefficient of 0.025 would increase the speed only 2.9 miles per hour, but if the speed remained the same, the power would be reduced 4 percent" (p. 1).

"Motion pictures were taken at 1,850 frames per second of the spray penetration and combustion occurring in the N.A.C.A. combustion apparatus arranged to operate as a compression-ignition engine. Indicator cards were taken simultaneously with the motion pictures by means of the N.A.C.A. optical indicator. The motion pictures showed that when ignition occurred during injection it started in the spray envelope. If ignition occurred after injection cut-off, however, and after considerable mixing had taken place, it was impossible to predict where the ignition would start" (p. 1).

"An aerodynamic analysis of the gyroplane rotating-wing system is presented herein. This system consists of a freely rotating rotor in which opposite blades are rigidly connected and allowed to rotate or feather freely about their span axis. Equations have been derived for the lift, the lift-drag ratio, the angle of attack, the feathering angles, and the rolling and pitching moments of a gyroplane rotor in terms of its basic parameters" (p. 1).

From Summary: "The investigation described in this report was made to determine the effectiveness of floating wing-tip ailerons as an airplane control in the spin. In these tests the ailerons, not being balanced, were set parallel to the axis of rotation, which is probably very nearly the attitude that balanced floating ailerons would assume in a spin. Rolling - and yawing moment coefficients are given as measured for the model with and without the ailerons, and computed values are given for the ailerons alone."

"This report gives a simple method of estimating the torsional stiffness of thin shells, such as box beams or stressed-skin wings under large torque loads. A general efficiency chart for shells in torsion is established, based on the assumption that the efficiency of the web sheet in resisting deformation decreases linearly with the average stress. The chart is used to calculate the torsional deflections of eight box beams, a test wing panel, and a complete wing; the results of the calculations are shown in comparison with the test results" (p. 1).

The results of towing tests made on two models at the request of the Bureau of Aeronautics, Navy Department, are presented. The first model represents the hull of the U.S. Navy PN-8 flying boat, in which the sponsors of the original hull are removed and auxiliary lifting vanes are fitted at the chines immediately forward of the main step. The tests showed that the altered form gave a large increase in hump resistance and a very undesirable spray formation through a large part of the speed range.

"This report presents towing tests made in the N.A.C.A. tank of a parent form and five variations of a flying-boat hull. The beams of two of the derived forms were made the same as that of the parent and the lengths changed by increasing and decreasing the spacing of stations. The lengths of the two others of the derived forms were made the same as that of the parent while the beams were changed by increasing and decreasing the spacing of buttocks, all other widths being changed in proportion. The remaining derived form has the same length and beam as the parent, but the lines of the forebody were altered to give a planing bottom with no longitudinal curvature forward of the step" (p. 1).

The results of a complete test in the N.A.C.A. tank on a model of the hull of Sikorsky S-40 flying boat ('American Clipper') are reported. The test data are given in tables and curves. From these data non-dimensional coefficients are derived for use in take-off calculations and the take-off time and run for the S-40 are computed. The computed take-off time was obtained by the Sikorsky Aviation Corporation in performance tests of the actual craft.

"So long a time was required for the disturbed water to become quiet after a model had been towed down the N.A.C.A. tank, that only 12 to 18 runs a day could be made. In order to shorten the time lost in waiting between runs, several different methods of suppressing the waves were tried. The most effective form of wave suppressor developed consists of wooden frames covered with fine copper screening and secured horizontally just beneath the surface of the water at the sides of the tank" (p. 1).

"The effect on engine performance of variations in the shape of the prechamber, the shape and direction of the connecting passage, the chamber volume using a tangential passage, the injection system, and the direction of the fuel spray in the chamber was investigated using a 5 by 7 inch single-cylinder compression-ignition engine. The results show that the performance of this engine can be considerably improved by selecting the best combination of variables and incorporating them in a single design. The best combination as determined from these tests consisted of a disk-shaped chamber connected to the cylinder by means of a flared tangential passage" (p. 1).

"This note presents the results of complete tank test of N.A.C.A. Models 22-A and 35, two flying-boat hulls of the deep pointed-step type with low dead rise. Model 22-A is a form derived by modification of Model 22, the test results of which are given in N.A.C.A. Technical Note No. 488. Model 35 is a form of the same type but has a higher length-beam ratio than either Model 22 or 22-A. Take-off examples are worked out using data from these tests and a previous test of a conventional model applied to an arbitrary set of design specifications for a 15,000-pound flying boat" (p. 1).

"The investigation was made to determine the effects of full-span and of partial-span split flaps on the aerodynamic characteristics of a tapered wing. Aerodynamic force tests were made in the N.A.C.A. 7 by 10 foot wind tunnel on a highly tapered Clark Y wing equipped with various split flaps. Two sizes of tapered-chord flaps were tested as full-span flaps, and a narrow tapered-chord flap was tested as a partial-span flap by cutting off portions first from the tip and then from the center" (p. 1).

"Prandtl's suggested use of a doubly infinite arrangement of airfoil images in the theoretical determination of wind-tunnel jet-boundary corrections was first adapted by Glauert to the case of closed rectangular jets. More recently, Theodorsen, using the same image arrangement but a different analytical treatment, has extended this work to include not only closed but also partly closed and open tunnels. This report presents the results of wind-tunnel tests conducted at the Georgia School of Technology for the purpose of verifying the five cases analyzed by Theodorsen" (p. 1).

"A type of fixed open slot so arranged that no flow would pass through it at a lift coefficient corresponding to high-speed flight was investigated in the N.A.C.A. 7 by 10 foot wind tunnel to determine the possibilities of such a high-lift device for increasing the speed-range ratio of a wing. The condition of no through flow was achieved by locating the slot openings at points of equal static pressure at the design lift coefficient as determined from the pressure distribution about the plain wing. Two models of Clark Y wings with such equal-pressure slots were tested and the smoke-flow patterns about them observed" (p. 1).

From Summary: "The investigation described in this report was made to determine the change in aerodynamic forces and moments produced by split flaps in a steady spin. The test were made with the spinning balance in the NACA 5-foot vertical wind tunnel. A low-wing monoplane model was tested with and without the split flaps in 12 spinning attitudes chosen to cover the probable spinning range. The results obtained indicate that the use of split flaps on an airplane is unlikely, in any case, to have much beneficial effect on a spin, and it might make the spin dangerous."

A description of a special type of seismograph, called a "landing-shock recorder," to be used for measuring the acceleration during impacts such as are experienced in airplane landings, is given . The theory, together with the assumptions made, is discussed in its relation to calculating the acceleration experienced in impact. Calculations are given from records obtained for two impacts of known acceleration. In one case the impact was very severe and in the other it was only moderately severe.

In this note, instruments for measuring altitude and rate of change of altitude in blind flying and landing of aircraft and their performance are discussed. Of those indicating the altitude above ground level, the sonic altimeter is the most promising. Its present bulk, intermittent operation, and more or less unsatisfactory means of indication are serious drawbacks to its use. The sensitive type aneroid altimeter is also discussed and errors in flying at a pressure level and in landing are discussed in detail.

"This paper contains a series of calculations showing how the performance of controllable propellers may be derived from data on fixed-pitch propellers given in N.A.C.A. Technical Report No. 350, or from similar data. Sample calculations are given which compare the performance of airplanes with fixed-pitch and with controllable propellers. The gain in performance with controllable propellers is shown to be largely due to the increased power available, rather than to an increase in efficiency" (p. 1).

"The ignition lag of a fuel oil in the combustion chamber of a high speed compression-ignition engine was measured by three different methods. The start of injection of the fuel as observed with a Stoborama was taken as the start of the period of ignition lag in all cases. The end of the period of ignition lag was determined by observation of the appearance of incandescence in the combustion chamber, by inspection of a pressure-time card for evidence of pressure rise, and by analysis of the indicator card for evidence of the combustion of a small but definite quantity of fuel" (p. 1).

Note presenting a method of estimating the variation of thrust horsepower with air speed, when the power unit consists of a conventional, thin, metal, fixed-pitch propeller driven by an internal-combustion engine. Such a curve is needed for the estimation of airplane performance in conjunction with a curve of horsepower required for maintaining level flight.

This report details the designs of high-speed aircraft from various countries from 1931 on, with special emphasis on the United States and Germany.

"The present report gives a method for computing the torsion of boxes with thin shear-resistant or simply tension-resistant walls under any torsional load, support and dimension. The final stress condition is developed from that of a principal system with unconstrained sectional warping corresponding to Bredt's formula and an additional stress condition due to constrained cross-sectional warping. This is computed by means of the deflection condition of the principal system from a statically indeterminate calculation" (p. 1).

This report was undertaken to give a brief summary of the laws governing the fatigue stresses and of the most important strength coefficients necessary for the correct dimensioning of the structural members. With consideration of the known fatigue strengths, the most important of which for airplane and engine materials are included in the paper, the fatigue strength of the structural parts can at least be approximately estimated.

In connection with the DVL Report 272 on the theory of the lateral stability of airplanes, the formal results are here amplified in some respects and their technical significance again briefly explained. Three numerical examples show how model tests for checking the lateral stability are to be evaluated and supplemented, if necessary, and how the stability limits depend on the design of the airplane and on the conditions of flight.