Report presenting an investigation on canopy pressures and canopy-fuselage forces and moments under conditions of combined pitch and sideslip. The canopy configurations tested varied in windshield shape (flat, vee, and round) and were tested at two Mach numbers and Reynolds numbers.

Report presenting zero-lift drag results for two 60 degree delta-wing configurations with air inlets. One had twin conical-shock semi-circular scoops just ahead of the wing-body juncture and one had a modified wing section over the inboard portion to allow installation of modified triangular inlets in the wing leading edge. Results regarding the drag coefficients and mass-flow ratios are provided.

Report presenting an investigation of a configuration with a body of fineness ratio 16.9, a 52.5 degree sweptback wing of aspect ratio 3, taper ratio 0.2, and NACA 65A004 airfoil section, and an incline tail which was aeropulsed continuously in pitching during free flight with and without a sustainer rocket motor operating. The Mach number range covered was from 1.4 to 2.3. Results regarding drag, total normal force and pitching moment, wing normal-force-curve slope, flow conditions at the horizontal tail, and cross coupling are provided.

Report discussing testing of a multijet 60 degree delta-wing airplane configuration with twin-engine exhausts at specified locations under the wing. Data was obtained for jet-on and jet-off conditions between a range of Mach numbers. Results are presented for the effect of jet on drag, jet effect on lift, static longitudinal stability, and dynamic longitudinal stability.

"The effect of dissolved oxygen in the filter-clogging characteristics of three JP-4 and two JP-5 fuels was studied at 300 degrees to 400 degrees F in a bench- scale rig, employing filter paper as the filter medium. The residence time of the fuel at the high temperature was approximately 6 seconds" (p. 1).

An investigation of the performance and operating characteristics of two variable-thrust injectors over a wide thrust range using mixed oxides of nitrogen and ammonia. Specific impulse, characteristic velocity, thrust coefficient, and overall efficiency are presented as functions of thrust. A maximum thrust range of 12 during one run was obtained with a triplet impinging-jet injector.

Report presenting local values of heat-transfer rate and temperature-recovery factor obtained on a transpiration-cooled flat plate. The results show primarily that transpiration cooling in a turbulent boundary layer at M = 2.7 has marked effects on the heat transfer and recovery temperature for nearly uniform air injection along the plate.

From Summary: "The procedure currently employed by the NACA Lewis Laboratory in the design of transpiration-cooled strut-supported turbine rotor blades is discussed. The strut is the internal blade supporting member and also serves to partition the blade into separate cooling-air passages. Orifices in the blade base, which meter the cooling-air to each internal passage, are used in conjunction with a constant chordwise permeability."

From Summary: "It is demonstrated with the aid of similitude arguments that a model launched from a hypervelocity gun upstream through a special supersonic nozzle should experience aerodynamic heating and resulting thermal stresses like those encountered by a long-range ballistic missile entering the earth's atmosphere. This demonstration hinges on the requirements that model and missile be geometrically similar and made of the same material, and that they have the same flight speed and Reynolds number (based on conditions just outside the boundary layer) at corresponding points in their trajectories. The hypervelocity gun provides the model with the required initial speed, while the nozzle scales the atmosphere, in terms of density variation, to provide the model with speeds and Reynolds numbers over its entire trajectory."

Inserting a splitter plate in the subsonic diffuser caused a pressure-recovery loss of about 1 percent for an inlet with a long nearly constant-area throat section. The loss was due to the increased surface area. Another inlet, which had a comparatively rapid area increase immediately after the throat, experienced pressure-recovery losses of 5 and 6 percent at Mach numbers of 1.8 and 2.0, respectively, and about 1 percent at Mach 1.5.

Report presenting an investigation at Mach number 1.94 of a series of triangular-wing and body combinations to determine the interference lift, drag, and pitching moment. The models had a series of seven flat-plate triangular wings of varying scale, four with semiapex angles of 30 degrees, and three with semiapex angles of 45 degrees. Results indicated that the interference between the wing and the body gave an increase in lift over the wing and body alone, but at the expense of more drag.

Engine performance is better for constant outer-spool mechanical-speed operation than for constant inner-spool mechanical-speed operation over most of the flight range considered. Combustor and afterburner frontal areas are about the same for the two modes. Engine performance for a mode characterized by a constant outer-spool equivalent speed over part of the flight range and a constant outer-spool mechanical speed over the rest of the flight range is better that that for constant outer-spool mechanical speed operation.

Aerodynamic characteristics of rectangular platform, all-movable controls combined with slender body of revolution at Mach 3 to 6.25. The results showed that lift variations with angle of attack were somewhat nonlinear for both control-body combinations tested.

Report presenting an investigation of the thermal-shock effect of water-spray impingement upon turbine rotor blades subjected to rated engine operating conditions using external water-spray cooling. Turbine-blade cooling water was turned on and off in cycles which employed either sudden or gradual injection of cooling water. Results regarding blades modified and unmodified for rotating injection are provided.

Memorandum presenting some physical and chemical properties of a sample of modified Hi-Cal-2. Some of the results obtained include chemical analysis, heat of combustion, density, freezing point, self-ignition temperature, flash point, oxygen stability, water stability test, infrared spectrum, and vapor pressure and decomposition are provided.

Memorandum presenting a supersonic wind-tunnel investigation of the origin and distribution of store interference performed in the 4- by 4-foot supersonic pressure tunnel at a Mach number of 1.6 in which separate forces on a store and on a 60 degree delta-wing-fuselage combination were measured. The configuration in this report simulates a heavy-bomber delta-wing airplane and has a large external symmetrical store that represents a nacelle with a frontal area equivalent to a twin-engine nacelle.

Report discussing testing of a Hughes Falcon missile, C configuration, to determine the stability and control characteristics of the missile while rolling. Information about the time histories, normal force due to angle of attack, pitching moment due to angle of attack, damping, and control effectiveness is provided.

Memorandum presenting an investigation conducted in the supersonic pressure tunnel on canopy pressures and canopy-fuselage forces and moments under conditions of combined pitch and sideslip. The canopy configurations tested varied in windshield shape, location on the fuselage, and fineness ratio. Results regarding force and moment data, pressure data, and force and pressure correlation are provided.

Report presenting the results of force and moment tests at a range of Mach numbers on two rectangular-plan-form, all-movable controls in combination with a slender body of revolution are presented and compared with the predictions of theory. The results showed that lift variations with angle of attack were somewhat nonlinear for both control-body combinations tested.

A study relating local-pressure fluctuations to static-pressure distributions on six two-dimensional airfoils. Total-pressure fluctuations and total-pressure loss in the wake of an NACA 65A008 airfoil are also compared. Results regarding local-pressure fluctuations on the models and total-pressure fluctuations in the wake of an NACA 65A008 airfoil are provided.

Stresses on the root fastenings of turbine blades were appreciably reduced by redesign of the root. The redesign consisted in curving the root to approximately conform to the camber of the airfoil and elimination of the blade platform. Full-scale jet-engine tests at rated speed using cermet blades of the design confirmed the improvement.

Report presenting experimental panel flutter data at a range of Mach numbers for buckled rectangular panels and the effect of a pressure differential. Increasing the pressure differential was found to eliminate flutter on most of the panels tested. Results regarding buckled panels clamped on the front and rear edges, bucked panels clamped on four edges, effect of lengthwise stiffeners on the flutter of a buckled panel, and panel flutter stresses are provided.

From Summary: "The results of an experimental investigation of the hinge-moment characteristics of a constant-chord control surface oscillating at high frequency is presented. The control surface was mounted on an aspect-ratio-2 triangular wing. The aerodynamic restoring-moment coefficient and damping-moment coefficient were determined at a frequency of 260 cycles per second for a Mach number range of 0.6 to 0.8 and 1.3 to 1.9 at angles of attack of 5 degrees and 10 degrees. The test results showed linear theory to be a reliable guide to the prediction of the trend of the restoring-moment coefficient with Mach number for the supersonic speed range of the investigation but overestimated the magnitude of the coefficient."

This report details a study that was conducted by the U.S. Naval Air Development Center to "determine the feasibility of several airborne magnetic mine-sweeping methods. The advantages of a satisfactory airborne method are greater safety and speed than are possible with existing surface methods." The configurations and results of the double Q-sweep, the modified double-catenary sweep, and the M-sweep are examined.