This presentation is a summary of the current research activities on fuels and lubricants in the Multi-discipline Tribology group and the engine test group in the Combustion Laboratory of the Pennsylvania State University. The progress areas discussed in this summary include those found in Table 1. Table 1. RESEARCH AREAS: Diesel Engine Emission Reduction; Oxygenated Fuels; Improved Friction Fuels; Vegetable Oil Lubricants; Extended Drain Lubricants; Effect of Chemical Structure on Friction and Wear. The research is of interest either directly or indirectly to the goal of this workshop, diesel engine emissions reduction. The current projects at Penn State in the areas listed above will be discussed.

Radionuclide and metal contaminants are present in the vadose zone and groundwater throughout the U.S. Department of Energy (DOE) weapons complex. Demonstrating in situ immobilization of these contaminants in vadose zones or groundwater plumes is a cost-effective remediation strategy. However, the implementation of in situ remediation requires definition of the mechanism that controls sequestration of the contaminants. One such mechanism for metals and radionuclides is co-precipitation of these elements in authigenic calcite and calcite overgrowths. Calcite, a common mineral in many aquifers and vadose zones in the arid western U.S., can incorporate divalent metals such as strontium, cadmium, lead, and cobalt into its crystal structure by the formation of solid solutions. The rate at which trace metals are incorporated into calcite is a function of calcite precipitation kinetics, adsorption interactions between the calcite surface and the trace metal in solution, solid solution properties of the trace metal in calcite, and also the surfaces upon which the calcite is precipitating. A fundamental understanding of the coupling of calcite precipitation and trace metal partitioning and how this may occur in aquifers and vadose environments is lacking. The focus of the research proposed here is to investigate the facilitated partitioning of metal and …

This project is a collaborative effort between the University of Akron, Illinois Institute of Technology and two industries: UOP and Energy International. The tasks involve the development of transient two and three dimensional computer codes for slurry bubble column reactors, optimization, comparison to data, and measurement of input parameters, such as the viscosity and restitution coefficients. To understand turbulence, measurements were done in the riser with 530 micron glass beads using a PIV technique. This report summarizes the measurements and simulations completed as described in details in the attached paper, ''Computational and Experimental Modeling of Three-Phase Slurry-Bubble Column Reactor.'' The Particle Image Velocimetry method described elsewhere (Gidaspow and Huilin, 1996) was used to measure the axial and tangential velocities of the particles. This method was modified with the use of a rotating colored transparent disk. The velocity distributions obtained with this method shows that the distribution is close to Maxwellian. From the velocity measurements the normal and the shear stresses were computed. Also with the use of the CCD camera a technique was developed to measure the solids volume fraction. The granular temperature profile follows the solids volume fraction profile. As predicted by theory, the granular temperature is highest at …

Administration and management of predoctoral fellowship program for the reporting period. The objective of the program was threefold: to create a pool of PhD's trained in the integrated approach to manufacturing and processing, to promote academic interest in the field, and to attract talented professionals to this challenging area of engineering. It was anticipated that the program would result in the creation of new manufacturing methods that would contribute to improved energy efficiency, to better utilization of scarce resources, and to less degradation of the environment. Emphasis in the competition was on integrated systems of manufacturing and the integration of product design with manufacturing processes.

Accidents could occur during the transportation of spent nuclear fuel and high-level radioactive waste. This paper describes the risks and consequences to the public from accidents that are highly unlikely but that could have severe consequences. The impact of these accidents would include those to a collective population and to hypothetical maximally exposed individuals (MEIs). This document discusses accidents with conditions that have a chance of occurring more often than 1 in 10 million times in a year, called ''maximum reasonably foreseeable accidents''. Accidents and conditions less likely than this are not considered to be reasonably foreseeable.

The ''Symposium on Microscale Separations and Analysis'' event, held as a section of the American Chemical Society Annual meeting on 27 August 2001, brought together engineers, physicists, and chemists from both academia and industry to discuss the latest research in the area of biomolecule analysis on microfluidic devices for genomic and proteomic applications.

Most of the anthropogenic emissions of carbon dioxide result from the combustion of fossil fuels for energy production. Photosynthesis has long been recognized as a means, at least in theory, to sequester anthropogenic carbon dioxide. Aquatic microalgae have been identified as fast growing species whose carbon fixing rates are higher than those of land-based plants by one order of magnitude. Physical Sciences Inc. (PSI), Aquasearch, and the Hawaii Natural Energy Institute at the University of Hawaii are jointly developing technologies for recovery and sequestration of CO{sub 2} from stationary combustion systems by photosynthesis of microalgae. The research is aimed primarily at demonstrating the ability of selected species of microalgae to effectively fix carbon from typical power plant exhaust gases. This report covers the reporting period 1 April to 30 June 2001 in which PSI, Aquasearch and University of Hawaii conducted their tasks. Based on the work conducted during the previous reporting period, PSI initiated work on the component optimization work. Aquasearch continued their effort on selection of microalgae suitable for CO{sub 2} sequestration. University of Hawaii initiated effort on system optimization of the CO{sub 2} sequestration system.

None

A National Center for Atmospheric Research (NCAR) Integrated Sounding System (ISS) was deployed about 5 km east of the WLEF-TV tower in Chequamegon National Forest, Wisconsin. The tower is instrumented for high-precision, high-accuracy CO{sub 2} mixing ratio measurements at six levels up to 396 m above ground and continuous eddy-covariance flux measurements at three levels up to 396 km. The ISS, including boundary layer radar profile, radio acoustic sounding system, and rawinsonde system was operated from March through October of 1998 and 1999. The NCAR ISS was also deployed at the Walker Branch flux tower in Oak Ridge, Tennessee from March through November of 1999. Continuous observations of atmospheric structure including radar reflectivity and horizontal wind profiles were collected at each site, and rawinsondes were launched at midday once per week. Boundary layer depths were derived from the radar reflectivity data. A combination of tall tower and radar boundary layer depths was us ed to describe the seasonal evolution of the diurnal mixing depth and its relationship to local turbulent forcing and synoptic conditions. These depths were compared with model predictions from a General Circulation Model (GCM). The proposed method of computing the jump in CO{sub 2} mixing ratio across …

The Class 2 Project at West Welch was designed to demonstrate the use of advanced technologies to enhance the economics of improved oil recovery (IOR) projects in lower quality Shallow Shelf Carbonate (SSC) reservoirs, resulting in recovery of additional oil that would otherwise be left in the reservoir at project abandonment. Accurate reservoir description is critical to the effective evaluation and efficient design of IOR projects in the heterogeneous SSC reservoirs. Therefore, the majority of Budget Period 1 was devoted to reservoir characterization. Technologies being demonstrated include: (1) Advanced petrophysics; (2) Three-dimensional (3-D) seismic; (3) Crosswell bore tomography; (4) Advanced reservoir simulation; (5) Carbon dioxide (CO{sub 2}) stimulation treatments; (6) Hydraulic fracturing design and monitoring; and (7) Mobility control agents.

The Fe-16 at. (8.5 wt) % Al alloy, known as FAPY, has been identified as a superior material for heating element applications. However, while the 15-lb heats melted at the Oak Ridge National Laboratory (ORNL) could be processed into wire, the large heat melted at Hoskins Manufacturing Company (Hoskins) could not be processed under commercial processing conditions. The primary objective of the Cooperative Research and Development Agreement (CRADA) was to demonstrate that wire of the FAPY alloy could be produced under commercial conditions from air-induction-melted (AIM) heats. The specific aspects of this CRADA included: (1) Melting 15-lb heats by AIM or vacuum-induction melting (VIM) at ORNL. (2) Development of detailed processing steps including warm drawing and annealing temperature and time during cold-drawing steps. (3) Melting of 1400-lb heats at Hoskins by the Exo-Melt{trademark} process and their chemical analysis and microstructural characterization. (4) Development of tensile properties of sections of ingots from the large heats in the ascast, hot-worked, and hot- and cold-worked conditions. (5) Microstructural characterization of cast and wrought structures and the fractured specimens. (6) Successful demonstration of processing of AIM heats at Hoskins to heating element wire. The aspects of this CRADA listed above have demonstrated that the …

This annual progress and performance evaluation report discusses the groundwater remedial actions in the 100 Area, including the interim actions at the 100-HR-3 and 100-KR-4 Operable Units, and also discusses the expedited response action in the 100-NR-2 operable unit.

A simplified and bounding methodology for analyzing the pressure buildup and hydrogen concentration within an unvented 2R container was developed (the 2R is a sealed container within a 6M package). The specific case studied was the gas buildup due to alpha radiolysis of water moisture sorbed on small quantities (less than 20 Ci per package) of plutonium oxide. Analytical solutions for gas pressure buildup and hydrogen concentration within the unvented 2R container were developed. Key results indicated that internal pressure buildup would not be significant for a wide range of conditions. Hydrogen concentrations should also be minimal but are difficult to quantify due to a large variation/uncertainty in model parameters. Additional assurance of non-flammability can be obtained by the use of an inert backfill gas in the 2R container.

A technical report of a monitoring study of bat flight and foraging activity above drained and undrained Carolina bays at the Savannah River Site (SRS), located near Aiken, South Carolina. In order to determine if the vegetational community type or structure of the forest community surrounding the bays affected bat activity levels, bat activity was monitored over 3 drained and 3 undrained reference bays surrounded by pine/mixed hardwood communities and 3 drained and 3 undrained reference bays surrounded by pine monocultures. Bat activity was monitored using time expansion bat detectors. Calls were recorded to Sony Professional tape recorders (Sony WMD3). Detectors positioned at 10 m heights were linked directly to the tape recorders. Time expansion radiomicrophones were used to monitor activity at 30 m heights. The radiomicrophones were attached to 2-m diameter helium balloons and suspended approximately 30 m above the forest floor. Calls detected by the radiomicrophones were transmitted via a FM narrowband frequency to a scanner on the ground.

An explanation is given of what a loop heat pipe (LHP) is, and how it works. It is then shown that neutron imaging (both real time neutron radioscopy and single exposure neutron radiography) is an effective experimental tool for the study of LHPs. Specifically, neutron imaging has helped to identify and correct a cooling water distribution problem in the condenser, and has enabled visualization of two-phase flow (liquid and vapor) in various components of the LHP. In addition, partial wick dry-out, a phenomenon of great importance in the effective operation of LHPs, has been identified with neutron imaging. It is anticipated that neutron radioscopy and radiography will greatly contribute to our understanding of LHP operation, and will lead to improvement of LHP modeling and design.

Radiation shielding analysis and design calculations were performed for remote maintenance cells of the proposed National Spallation Neutron Source (NSNS) facility. In the analysis, a calculational strategy utilizing coupled high energy Monte Carlo calculations and multidimensional discrete ordinates calculations was implemented to perform an activation analysis and shielding assessment of the NSNS remote handling cells. A general description of the remote maintenance cells, the methodology employed, and preliminary results of the shielding analysis and recommendations are presented.

Due to the short wavelengths of X-rays and low numerical aperture of the Fresnel zone plates used as X-ray objectives, the depth of field is several microns. Within the focal depth, imaging a thick specimen is to a good approximation equivalent to projecting the specimen absorption. Therefore, computed tomography based on a tilt series of X-ray microscopic images can be used to reconstruct the local linear absorption coefficient and image the three-dimensional specimen structure. To preserve the structural integrity of biological objects during image acquisition, microscopy is performed at cryogenic temperatures. Tomography based on X-ray microscopic images was applied to study the distribution of male specific lethal 1 (MSL-1), a nuclear protein involved in dosage compensation in Drosophila melanogaster, which ensures that males with single X chromosome have the same amount of most X-linked gene products as females with two X chromosomes. Tomographic reconstructions of X-ray microscopic images were used to compute the local three-dimensional linear absorption coefficient revealing the arrangement of internal structures of Drosophila melanogaster cells. Combined with labelling techniques, nanotomography is a new technique to study the 3D distribution of selected proteins inside whole cells. We want to improve this technique with respect to resolution and specimen …

A unique approach to crack-free joining of heterogeneous ceramics is demonstrated by the use of sialon polytypoids as Functionally Graded Materials (FGM) as defined by the phase diagram in the system, Si3N4-Al2O3. Polytypoids in the Al2O3-Si3N4 system offer a path to compatibility for such heterogeneous ceramics. The first part of the dissertation describes successful hot press sintering of multilayered FGM's with 20 layers of thickness 500 mm each. Transmission Electron Microscopy was used to identify the polytypoids at the interfaces of different areas of the joint. It has been found that the 15R polytypoid was formed in the Al2O3-contained layers and the 12H polytypoid was formed in the Si3N4-contained layers. The second part of the dissertation discusses the mechanical properties of these polytypoidally joined Si3N4-Al2O3. The thermal stresses of this FGM junction were analyzed using a finite element analysis program (FEAP) taking into account both coefficient of thermal expansion (CTE) and modulus variations. From this analysis, the result showed a dramatic decrease in radial, axial and hoop stresses as the FGM changes from three layers to 20 graded layers. Scaling was considered, showing that the graded transition layer should constitute about 75 percent or more of the total sample thickness …

This research project focuses on pollutants from the combustion of mixtures of dried municipal sewage sludge (MSS) and coal. The objective is to determine the relationship between (1) fraction sludge in the sludge/coal mixture, and (2) combustion conditions on (a) NOx concentrations in the exhaust, (b) the size segregated fine and ultra-fine particle composition in the exhaust, and (c) the partitioning of toxic metals between vapor and condenses phases, within the process. To this end work is progress using an existing 17kW downflow laboratory combustor, available with coal and sludge feed capabilities. The proposed study will be conducted in concert with an existing ongoing research on toxic metal partitioning mechanisms for very well characterized pulverized coals alone. Both high NOx and low NOx combustion conditions will be investigated (unstaged and staged combustion). The proposed work uses existing analytical and experimental facilities and draws on 20 years of research on NO{sub x} and fine particles that has been funded by DOE in this laboratory. Four barrels of dried sewage sludge are currently in the laboratory. Insofar as possible pertinent mechanisms will be elucidated. Tradeoffs between CO{sub 2} control, NO{sub x} control, and inorganic fine particle and toxic metal emissions will be …

None

The scaling of energy transport with dimensionless parameters has been measured in high temperature plasmas with the goals of guiding theory and predicting energy confinement in future fusion devices. Validation of this approach requires demonstration of similarity in plasmas with identical dimensionless parameters but very different physical parameters. Within measurement uncertainties, the heat diffusivities and global energy confinement exhibit similarity in high confinement regimes on the DIII-D and JET tokamaks and in low confinement regimes on the DIII-D and AlcatorC-Mod tokamaks.

None

The first horizontal well ever in the Marchand sandstone has been drilled. Although major difficulties arose with certain aspects of the drilling operation, a horizontal section of approximately 1300 was drilled. The section was left open hole as planned. The shales just above and between the Marchand sands appear to be very water-sensitive, requiring careful drilling practices. These shales were encountered in the middle part of the curve (45{sup o}-60{sup o}), which can be the most difficult part of a directional well to clean. Difficulties with these shales and cleaning this section led to a parted drill string, requiring a sidetrack. There were no major geologic ''surprises'', such as formation tops coming in much shallower or deeper than expected, or unexpected faults. Thin kaolinite beds were encountered in the horizontal section of the well. Previous descriptions of the mineralogy of this formation did not mention any kaolinite. The lateral extent of these beds is unknown. Completion of the well is under way. One additional injection profile was gathered during the quarter. Results are consistent with other recently profiles that show gas within the C Sand is overriding the oil and failing to sweep the deeper parts of the reservoir. International …

Researchers of the Oak Ridge National Laboratory's (ORNLs) Power Electronics and Electric Machine Research Center (PEEMRC) collaborated with Visual Computing Systems (VCS) to develop an electric axial-gap permanent magnet (PM) motor controlled by a self-sensing inverter for driving vehicle accessories such as power steering, air conditioning, and brakes. VCS designed an 8 kW motor based on their Segmented Electromagnetic Array (SEMA) technology. ORNL designed a 10 kW inverter to fit within the volume of a housing, which had been integrated with the motor. This modular design was pursued so that multiple modules could be used for higher power applications. ORNL built the first inverter under the cooperative research and development agreement (CRADA) ORNL 98-0514 and drove a refurbished Delta motor with no load during the Merit Review at ORNL on Monday, May 17, 1999. Inverter circuitry and instructions for assembling the inverters were sent to VCS. A report was prepared and delivered during the Future Car Congress in April 2000, at Arlington, Virginia. Collaboration continued under CRADA ORNL 99-0568 as VCS designed and built a SEMA motor with a dual coil platter to be the traction motor for an electric truck. VCS and ORNL assembled two 45 kW inverters. Each …