Memorandum presenting the results of an investigation of the stability, control, and induced rolling moments of a canard missile with cruciform wings of rectangular plan form at Mach number 1.7. All data including the measured hinge moments of the canard control surfaces, the axial forces on the complete missile, and the forces and moments on the various combinations of the missile components are presented in tabular form.

Memorandum presenting the effect of blunting on the internal performance of a two-cone inlet with an internally cylindrical cowl investigated experimentally at Mach number 4.95. Total-pressure-recovery and mass-flow data were obtained for a range of spike and cowl bluntness.

Report presenting an investigation of the effect of inlet component blunting on performance using an axisymmetric external-compression inlet in the supersonic wind tunnel. The investigation was carried out to determine the performance penalties associated with spike-tip and cowl-lip blunting. Results regarding the effect of rounding the spike tip on inlet performance, overall drag coefficients, flow distortion, and Schileren photographs are provided.

"A rocket of the 1000-pound-thrust class using liquid oxygen and JP-4 fuel as propellant was installed in the Lewis 8- by 6-foot tunnel to permit a controlled study of some of the factors affecting the heating of a rocket-missile base. Temperatures measured in the base region are presented from findings of three motor extension lengths relative to the base. Data are also presented for two combustion efficiency levels in the rocket motor" (p. 1).

"Investigation of the control parameters of an external-internal compression inlet indicates that the cowl-lip shock provides a signal to position the spike and to start the inlet over a Mach number range from 2.1 to 3.0. Use of a single fixed probe position to control the spike over the range of conditions resulted in a 3.7-count loss in total-pressure recovery at Mach 3.0 and 0 deg angle of attack. Three separate shock-sensing-probe positions were required to set the spike for peak recovery from Mach 2.1 to 3.0 and angles of attack from 0 deg to 6 deg" (p. 1).

Memorandum presenting an investigation in the 9-inch supersonic tunnel of several missiles with low-aspect-ratio, cruciform, tandem lifting surfaces with a view toward developing a missile with small variations of center-of-pressure location at various angles of attack and roll. The investigation centered about a basic configuration with equal-span wings and tails.

Memorandum presenting the results of an investigation of the stability, control, and induced rolling moments of a canard missile with cruciform wings of rectangular plan form at Mach number 1.7. All of the data obtained, including the measured hinge moments of the canard control surfaces, axial forces on the complete missile, and forces and moments on the various combinations of missile components are presented in tabular form.

Report presenting an investigation of the aerodynamic loads on a leading-edge slat on a 40 degree sweptback wing with NACA 64(sub 1)-112 airfoil sections in the low-turbulence pressure tunnel. Results regarding wing force data, slat force data, and slat pressure distributions are provided.

Report presenting an investigation in the free-flight tunnel to determine the dynamic lateral stability and control characteristics of a high-aspect-ratio bomber model with a sweptback-wing fighter model attached to each wing tip with freedom in roll. The results indicated that the longitudinal position of the fighters with respect to the bomber had an important effect on the flight behavior of the coupled configuration.

Report presenting the results of a flight investigation of the lateral stability and control characteristics of a high-speed fighter airplane. Results regarding the control-free lateral oscillations, sideslip characteristics, rudder control characteristics, rudder hinge-moment characteristics, and rolling characteristics are provided.

Report presenting an investigation in the altitude test chamber to evaluate several afterburner configurations on the XJ79 engine. Data were obtained from nine configurations which show the effect on burner performance of increased burner diameter and modifications to the flameholder, fuel system, and flow swirl.

Report presenting the effect of inlet component blunting on performance using an axisymmetric external-compression inlet in order to determine the performance penalties associated with spike-tip and cowl-lip blunting. The data can be used as a design guide for blunt inlet components applicable to cooling techniques. Results regarding the effect of tip rounding, drag coefficients, flow distortion, lip blunting, and Schileren photographs are provided.