The following report describes the developmental process of the determination of free nitric acid in solutions containing uranyl nitrate, aluminum nitrate and sodium dichromate.

Introduction: "This report covers progress on the testing of the General Engineering and Consulting Laboratories Turbine Pump No. 1 from May 1, 1948 to Jun 15, 1948. All testing prior to April 30, 1948 has been described in Redox Experiment Testing Report No. 1 (Document HW-9474) and No. 2 (Document HW-9694)."

"This report gives briefly a rather simple method for fabricating foils from uranium buttons. Two log sheets one of a U-238 run and one of a U-255 run are given."

Report discussing the results of research conducted by the Hanford Works Analytical Research Group during the period from March 1949 to April 1949.

This report studies the effect of x irradiation on the maturation of the circulating reticulocytes, using samples of rabbit blood with and without phenylhydresine- or bleeding-induced anemia and comparing them to the blood of human subjects under similar circumstances.

Report discussing an investigation into several types and sizes of flaps and spoilers located forward of the elevators on the upper surface of the horizontal stabilizer of a model of a radial-engine pursuit airplane. Information about the elevator characteristics, elevator-fixed and elevator-free balance lift coefficient, and trim drag coefficient for a range of Mach numbers is provided.

This document contains reproductions of the technical papers presented at the NACA - University Conference on Aerodynamics held at the Langley Aeronautical Laboratory on June 21, 22, and 23, 1948. The conference was held in recognition of the difficulties, imposed by security restrictions, in keeping abreast of the rapid advances in aerodynamics. The papers were prepared to review the status of a number of fields of interest, to summarize the more important wartime advances that are no longer classified, and to orient reference material for further study.

Report discussing the hydrodynamic characteristics of a flying boat with a low-drag, planing-tail hull compared with a conventional-type hull. The planing-tail model had more take-off stability than the conventional model and had lower hydrodynamic resistance. Information about the landing stability, variation of trim with speed, and spray characteristics is also provided.

Report presenting tests at Mach numbers between 1.36 and 2.01 of a twin-scoop air intake enclosing 61.5 percent of the maximum circumference of a body of revolution and located five forebody diameters behind the apex, which showed that the total pressure recovered after diffusion was about 10 percent greater than that attained in previous tests with an annular entrance of the same area.

Report presenting the results of tests on a model of a jet-propelled airplane and a comparison of drag, maximum lift coefficient, and elevator angle required for level flight in the wind tunnel and in flight. Results regarding the aerodynamic characteristics, longitudinal control, wing pressure distribution, and dive-recovery flaps are provided.

"On the basis of a recently developed theory for finite sweptback wings at supersonic speeds, calculations of the supersonic wave drag at zero lift were made for a series of wings having thin symmetrical biconvex sections with untapered plan forms and various angles of sweepback and aspect ratios. The results are presented in a unified form so that a single chart permits the direct determination of the wave drag for this family of airfoils for an extensive range of aspect ratio and sweepback angle for stream Mach numbers up to a value corresponding to that at which the Mach line coincides with the wing leading edge. The calculations showed that in general the wave-drag coefficient decreased with increasing sweepback" (p. 1).

Report presenting an investigation of a one-eighth segment of an annular combustor suitable for use as a component of an experimental turbojet engine. Due to the small space available for the combustor, a special design involving a minimum of obstructions in the combustion chamber was created. Results regarding the temperature-rise efficiency, total-pressure loss, and exhaust-gas temperature variation for several simulated engine operating conditions are provided.

Results of wind-tunnel tests of a semispan model of a triangular wing of aspect ratio 2 with a skewed wing-tip flap are presented. Lift, drag, pitching-moment, and hinge-moment data are included for subsonic Mach numbers up to 0.95. The flap showed extremely high hinge moments and low effectiveness as a longitudinal control. Although less affected by compressibility, this flap is indicated to be inferior to a constant-chord flap when applied to this triangular wing.

Report presenting testing of a series of thin, triangular plan-form wings, including eight triangular wings of vertex angles and three swept-back wings with circular-arc sections. Results regarding lift, center of pressure, and ideal operation of different types of wings are provided.

From Introduction: "This paper presents the results of the investigation of wing-alone and wing-fuselage combinations employing a wing with the quarter-chord line swept back 35^o, aspect ratio 4, taper ratio 0.6, and NACA 65A006 airfoil section."

From Introduction: "This report presents the aerodynamic characteristics at low speed end high Reynolds number as determined in the Ames 40- by 80 foot wind tunnel."

"An investigation of the rolling effectiveness at transonic and supersonic speeds of a wing-aileron configuration simulating the D-558-2 airplane has been made by means of a rocket-propelled test vehicle. The variation of rolling effectiveness with Mach number is similar to that obtained previously for tapered sweptback wings having full-span, 0.2-chord ailerons" (p. 1).

Report presenting an investigation of a 24-inch-diameter rotor for a supersonic axial-flow compressor in air up to an actual tip speed of 1654 feet per second and a maximum equivalent tip speed of 1765 feet per second. Results regarding overall performance, rotor-inlet characteristics, rotor-passage flow characteristics, and rotor-outlet characteristics are provided.

Report presenting a semispan triangular wing with a constant-chord trailing-edge flap to evaluate the aerodynamic characteristics of the wing with landing speeds up to a Mach number of 0.95. Tests were included to ascertain the effects of the addition of a body and of modifications to the airfoil section. Results regarding the wing alone with low Mach number, wing alone with high Mach number, effect of the body, effect of the flap, effect of Mach number, lift-drag ratio, and wing-profile modifications are provided.

Memorandum presenting equations for obtaining the wall coordinates of two-dimensional supersonic nozzles. The equations are based on the application of the method of characteristics to irrotational flow of perfect gases in channels. A brief discussion of characteristics as applied to nozzle design is given to assist in understanding and applying the nozzle-design method of the report.

Report presenting part of the results obtained to determine the effects of compressibility at high Mach numbers on a model of the Bell XS-1 transonic research airplane. General trends that can be qualitatively analyzed for level-flight Mach numbers up to 0.93 are given. Results regarding force characteristics and a comparison of results with wing-flow investigation are also provided.

Report presenting testing on parabolic bodies of revolution of two fineness ratios in the transonic and supersonic range. One had a body fineness ratio of 7.87 and one had a ratio of 12 and were tested under different Mach number ranges. Experimental results and drag estimates of various portions of the body are provided.

Report presenting static-pressure measurements made through the speed of sound by the NACA wing-flow method at the back of two unswept circular cylinders and one sweptback cylinder. Static pressures were found to decrease considerably with an increase in Mach number. Information about the length and diameter of the cylinders and how it affects measurements is provided.

Report presenting testing of seven models that from two different wing series: a series of taper ratio 0.5 and differing aspect ratio and a series of aspect ratio 4 and differing taper ratio. Measurements of lift, drag, and pitching moment were made at Mach number 1.53. The aerodynamic parameters generally varied with aspect ratio and taper ratio in the manner indicated by the linear theory.