Zircaloy cladding tubes strain in-situ during service life in the corrosive environment of a Pressurized Water Reactor for a variety of reasons. First, the tube undergoes stress free growth due to the preferential alignment of irradiation induced vacancy loops on basal planes. Positive strains develop in the textured tubes along prism orientations while negative strains develop along basal orientations (Reference (a)). Second, early in life, free standing tubes will often shrink by creep in the diametrical direction under the external pressure of the water environment, but potentially grow later in life in the diametrical direction once the expanding fuel pellet contacts the cladding inner wall (Reference (b)). Finally, the Zircaloy cladding absorbs hydrogen as a by product of the corrosion reaction (Reference (c)). Once above the solubility limit in Zircaloy, the hydride precipitates as zirconium hydride (References (c) through (j)). Both hydrogen in solid solution and precipitated as Zirconium hydride cause a volume expansion of the Zircaloy metal (Reference (k)). Few studies are reported on that have investigated the influence that in-situ clad straining has on corrosion of Zircaloy. If Zircaloy corrosion rates are governed by diffusion of anions through a thin passivating boundary layer at the oxide-to-metal interface (References …

A simple, approximate analysis of the effect of differing cathode and anode areas on the measurement of cell performance on anode-supported solid oxide fuel cells, wherein the cathode area is smaller than the anode area, is presented. It is shown that the effect of cathode area on cathode polarization, on electrolyte contribution, and on anode resistance, as normalized on the basis of the cathode area, is negligible. There is a small but measurable effect on anode polarization, which results from concentration polarization. Effectively, it is the result of a greater amount of fuel transported to the anode/electrolyte interface in cases wherein the anode area is larger than the cathode area. Experiments were performed on cells made with differing cathode areas and geometries. Cathodic and anodic overpotentials measured using reference electrodes, and the measured ohmic area specific resistances by current interruption, were in good agreement with expectations based on the analysis presented. At 800 C, the maximum power density measured with a cathode area of {approx}1.1 cm{sup 2} was {approx}1.65 W/cm{sup 2} compared to {approx}1.45 W/cm{sup 2} for cathode area of {approx}2 cm{sup 2}, for anode thickness of {approx}1.3 mm, with hydrogen as the fuel and air as the oxidant. At …

SnadiOpt is a package that supports the use of the automatic differentiation package ADIFOR with the optimization package Snopt. Snopt is a general-purpose system for solving optimization problems with many variables and constraints. It minimizes a linear or nonlinear function subject to bounds on the variables and sparse linear or nonlinear constraints. It is suitable for large-scale linear and quadratic programming and for linearly constrained optimization, as well as for general nonlinear programs. The method used by Snopt requires the first derivatives of the objective and constraint functions to be available. The SnadiOpt package allows users to avoid the time-consuming and error-prone process of evaluating and coding these derivatives. Given Fortran code for evaluating only the values of the objective and constraints, SnadiOpt automatically generates the code for evaluating the derivatives and builds the relevant Snopt input files and sparse data structures.

In this paper, by systematically treating the integrals involved in the piezoelectric inclusion problem, explicit results were obtained for the piezoelectric Eshelby tensors for a spheroidal inclusion aligned along the axis of the anisotropy in a transversely isotropic piezoelectric material. This problem was first treated by Dunn and Wienecke (1996) using a Green's function approach, which closely follows Withers' approach (1989) for an ellipsoidal inclusion problem in a transversely isotropic elastic medium. The same problem was recently treated by Michelitsch and Levin (2000) also using a Green's function approach. In this paper, a different method was used to obtain the explicit results for the piezoelectric Eshelby tensors for a spheroidal inclusion. The method is a direct extension of a more unified approach, which has been recently developed by Mikata (2000), which is based on Deeg's results (1980) on a piezoelectric inclusion problem. The main advantage of this method is that it is more straightforward and simpler than Dunn and Wienecke (1996), or Michelitsch and Levin (2000), and the results are a little bit more explicit than their solutions. The key step of this paper is an analytical closed form evaluation of several integrals, which was made possible after a careful …

An integrated code system consisting of RELAP5-3D and a multiphase CFD program has been created through the use of a generic semi-implicit coupling algorithm. Unlike previous CFD coupling work, this coupling scheme is numerically stable provided the material Courant limit is not violated in RELAP5-3D or at the coupling locations. The basis for the coupling scheme and details regarding the unique features associated with the application of this technique to a four-field CFD program are presented. Finally, the results of a verification problem are presented. The coupled code system is shown to yield accurate and numerically stable results.

17th Edition of TOP500 List of World's Fastest Supercomputers Released MANNHEIM, GERMANY; KNOXVILLE, TENN.; BERKELEY, CALIF. In what has become a much-anticipated event in the world of high-performance computing, the 17th edition of the TOP500 list of the world's fastest supercomputers was released today (June 21). The latest edition of the twice-yearly ranking finds IBM as the leader in the field, with 40 percent in terms of installed systems and 43 percent in terms of total performance of all the installed systems. In second place in terms of installed systems is Sun Microsystems with 16 percent, while Cray Inc. retained second place in terms of performance (13 percent). SGI Inc. was third both with respect to systems with 63 (12.6 percent) and performance (10.2 percent).

The effort to define guidance for authentication of software for arms control and nuclear material transparency measurements draws on a variety of disciplines and has involved synthesizing established criteria and practices with newer methods. Challenges include the need to protect classified information that the software manipulates as well as deal with the rapid pace of innovation in the technology of nuclear material monitoring. The resulting guidance will shape the design of future systems and inform the process of authentication of instruments now being developed. This paper explores the technical issues underlying the guidance and presents its major tenets.

The Very Large Hadron Collider (or Eloisatron) represents what may well be the final step on the energy frontier of accelerator-based high energy physics. While an extremely high luminosity proton collider at 100-200 TeV center of mass energy can probably be built in one step with LHC technology, that machine would cost more than what is presently politically acceptable. This talk summarizes the strategies of collider design including staged deployment, comparison with electron-positron colliders, opportunities for major innovation, and the technical challenges of reducing costs to manageable proportions. It also presents the priorities for relevant R and D for the next few years.

In partnership with the City of San Diego, the U.S. Department of Energy funded a study to determine the feasibility of developing up to a 1 MW Brightfield on a landfill.