The 277W Building high bay roof area was load tested according to the approved load-test procedure, WHC-SD-GN-TP-30015, Revision 1. The 277W Building is located in the 200 West Area of the Hanford Site and has the following characteristics: roof deck -- wood decking supported by 4 x 14 timber purlins; roof membrane -- tar and gravel; roof slope -- flat (<10 deg); and roof elevation -- maximum height of about 63 ft. The 227W Building was visited in March 1994 for a visual inspection. During this inspection, cracked areas were visible in the decking, but it was not possible to determine whether these cracks extended completely through the decking, which is 2-in. thick. The building was revisited in March 1994 for the purpose of writing this test report. Because the roof requires personnel access, a test was determined to be the best way to qualify the roof. The conclusions are that the roof has been qualified for 500-lb total roof load and that the ``No Roof Access`` signs can be changed to ``Roof Access Restricted`` signs.

The Field Verification Program establishes a uniform and systematic process to ensure that technical information depicted on selected engineering drawings accurately reflects the actual existing physical configuration. This document defines the Field Verification Program necessary to perform the field walkdown and inspection process that identifies the physical configuration of the systems required to support the mission objectives of K Basins. This program is intended to provide an accurate accounting of the actual field configuration by documenting the as-found information on a controlled drawing.

The UO{sub 3} Plant went through a clean out leading to the deactivation of the facility. This clean out consisted of three phases. Phase 1 consisted of the removal of residual process material and the deactivation of most process equipment and instrumentation. Phase 2 consisted of the fixing or removal of contamination so storm water processing would be no longer required. Phase 3 consisted of the remaining activities that had to be completed before the facility was turned over to the Surplus Facility Program. Since the activities of Phase 2 and 3 were closely related, these two phases were worked simultaneously. The first part of this document summarizes the Phase 1 clean out procedures and their results. Phase 1 was completed on February 28, 1994. The second part summarizes the Phase 2/3 clean out procedures and their results. Phase 2/3 was completed before December 31, 1994. Because tanks and equipment were flushed simultaneously or in a specific sequence, the clean out processes are discussed per workplan.

Sample projections have been categorized into 7 major areas: Environmental Restoration, Tank Waste Remediation, Solid Waste, Liquid Effluents, Site Monitoring, Industrial Hygiene, and General Process Support Programs. The estimates are through the Fiscal Year 2000 and are categorized by radiation level. The yearly sample projection for each program will be categorized as follows: Category 1: Non-Radioactive; Category 2: <1 mR/hr {beta}/{gamma}; <10 nCi/g {alpha}; Category 3: 1 mR/hr {beta}/{gamma} to <10 mR/hr {beta}/{gamma}; and <10 nCi/g {alpha}; Category 4: <10 mR/hr {beta}/{gamma}; and <200 nCi/g {alpha}; Category 5: 10 mR/hr {beta}/{gamma} to <100 mR/hr {beta}/{gamma}; and <200 nCi/g {alpha}; Category 6: >100 mR/hr {beta}/{gamma}; and Category 7: >200 nCi/g {alpha}.

The theoretical and experimental status of high energy spin phenomena is summarized, with emphasis on the spin properties of nucleons. It is stressed that crucial tests of the Standard Model can be made with polarization experiments. By performing the experiments discussed here, the authors will reveal important constituent and composite properties of protons and neutrons. The future prospects for planned polarization experiments are discussed.

This acceptance Test Procedure (ATP) has been prepared to demonstrate that modifications to the Fir Protection systems function as required by project criteria. The ATP will test the Fire Alarm Control Panels, Flow Alarm Pressure Switch, Heat Detectors, Smoke Detectors, Flow Switches, Manual Pull Stations, and Gong/Door By Pass Switches.