The purpose of the test was to check the extraction crane rails in the area of the reactor pit for level and parallelism. The west extraction crane rail exceeded the allowed tolerance of 1/32 inch at only one location. The elevation of the north bumper was out of tolerance by 1/64 inch. The east extraction crane rail was consistently lower than the west rail by as much as 8/64 inch. The east rail was parallel with the west rail within allowable tolerances over the length tested except at one location where the transit was located, approximately 41 feet from the north bumper.

The purpose of the test was to determine if failed blanket elements exist in other regions of the core beside F-2. FEDAL sampling ports that have indicted the greatest deviation as determined in a statistical analysis performed on a number of traverses in the FEDAL system will be tested. Data obtained from the start up runs of the FEDAL sample port Nos. 11, 31, 36 and 37 of Monitor 2 and port Nos. 14, 46, 11, 49 and 7 of Monitor 1 gave no indications of a blanket element failure. At each power increase, the radiation increase was normal with no signs of bursts or peaks of radiation which would indication the failure of a blanket fuel element.

The purpose of the test was to determine the radiation levels inside the concrete enclosures but outside the reactor plant containers after shutdown following plant power operation. Radiation levels at the survey points in the 1-AC and 10BD Boiler Chambers Enclosures and in the Reactor Container Enclosure indicated that no significant radiation hazards were present approximately 25 minutes after all rods had been inserted. The radiation levels approximately 4 minutes after shutdown at the survey points in the Auxiliary Chamber Enclosure indicated that several points were above background, the highest test level being obtained in contact with the East Auxiliary Chamber container drain pipe.

The purpose of the test was to determine the operating conditions of the rod drive mechanisms so that operating personnel may be informed concerning malfunctioning mechanisms. The results the this test favorably agree with previous results. The operating characteristics of the rod drive mechanisms checked in this test have not changed appreciably.

This review lists some of the salient features of semiconductor particle counters and cannot claim to contain an exhaustive listing of all the work in the field. Performance results on the surface-barrier counters as developed at California Institute of Technology are included as typical for this type of counter, though comparable results have been obtained elsewhere.

Results are summarized on theoretical considerations of the excited states of the Ca isotopes, experimental studies of the level structure of Ca42 and Ca44, studies of the production of circularly polarized bremsstrahlung by beta rays, the Moller scattering spectrometer, and the Moller scattering coincidence experiment.

An analysis to screen the various particle-collection systems which might be used for sampling the upper atmosphere with a rocket sampling vehicle has been undertaken. Although the current model of the Goetz Aerosol Spectrometer is not suitable, a high-flow-rate sampler of this general type, if it can be designed, appears promising. The design of such a sampler will be undertaken in future work. If a workable design is possible, this method would appear to be the most promising of all.

The relation between the maximum permissible transverse energies of particles that can be focused, the azimuthal energy, and the beam width is discussed relative to Megatron coil design. It is shown that deep potential wells for focusing can be obtained only at the expense of a narrow beam. (C.J.G.)

The original goal of this investigation was to compare the thermodynamic characteristics of the gases in and behind the shock fronts in gases at initial pressures in the millimeter range and to compare these characteristics in the geometries of single and double discharges. The shock fronts were not visible, so it was not possible, at these pressures, to get visual data from the shock front itself. The parameters giving the properties of the gases were faces. Measurements made with an image converter camera (which is still in the development stage) agree well with these made with a photomultiplier tube. Differences are observed between the front velocities in the cases studied. These are of the order of 3 to 15 per cent. Considering the nature of the shot to shot fluctuations in the discharges and the inductance variation between the single and double discharges represent a physical difference. The mathematical treatment which says that two equal strength colliding with a wall behaves, has not been shown to be inadequate by this investigation. It was hoped that a stronger confirmation could be fien to the theory, but the accuracy of the data does not warrant it.