A summary of the activities in the 4th operational year is presented for the ORR. On-stream time at 30 Mw was relatively steady with 75.4 and 83.7% representing the lowest and highest quarters. Modification of the ball-latch mechanism of the shim-rod-drives is in progress. The primary cooling system bypass control valve was modified and a d-c pony motor was added at the No. 3 primary pump. This addition was made to increase the reliability of adequate water flow for afterheat cooling. A study of coreboiling detection is being conducted. (J.R.D.)

The BCD Silicon strip Vertex Detector is constructed of 10 identical central region modules and 18 similar forward region modules. This memo describes a method of assembling these modules from individual silicon wafers. Each wafer is fitted with associated front end electronics and cables and has been tested to insure that only good wafers reach the final assembly stage. 5 figs.

The solar desiccant air conditioner (SODAC) system and its operation are described, including the characteristics of the major components, the performance at design conditions, and the control schemes for optimum operation in various climates. The system uses granular silica gel as a desiccant. It may operate in either a recirculated mode (no air exchange between the outside and the conditioned space) or a ventilated mode (air exchanged between outside and conditioned space). The test data in the ventilated mode at design flow rates are presented. Data include outdoor and indoor inlet wet and dry bulb temperatures, indoor outlet dry and wet bulb temperatures, capacity, coefficient of performance, air flow rates, hot water temperature, and solar heat used. The effects of indoor, outdoor, and hot water temperatures on the capacity and coefficient of performance are shown graphically, and the recirculated and ventilated modes, performances are compared. (LEW)

This document contains the input and output for the Policy Analysis Screening System (PASS) demonstration. This demonstration is stored on a portable disk at the Environmental Impacts Division. Sample queries presented here include: (1) how to use PASS; (2) estimated 1995 energy consumption from Mid-Range Energy-Forecasting System (MEFS) data base; (3) pollution projections from Strategic Environmental Assessment System (SEAS) data base; (4) diesel auto regulations; (5) diesel auto health effects; (6) oil shale health and safety measures; (7) water pollution effects of SRC; (8) acid rainfall from Energy Environmental Statistics (EES) data base; 1990 EIA electric generation by fuel type; sulfate concentrations by Federal region; forecast of 1995 SO/sub 2/ emissions in Region III; and estimated electrical generating capacity in California to 1990. The file name for each query is included.

The costs of pot calcination of Purex and Thorex wastes were calculated. The wastes were assumed produced by a plant processing 1500 ton/year of U converter fuel at a burnup of 10,000 Mwd/ton and 270 ton/year of Th converter fuel at 20,000 Mwd/ton. Costs were calculated for processing Purex waste in acidic and reacidified forms and for processing Thorex wastes in acidic and reacidified forms and with constituents added for producing an acidic Thorex glass. Calcination vessel designs were right circular cylinders similar to those used in engineering development studies. Costs were calculated for processing in 6-, 12-, and 24-in.-dia vessels with a fixed length of 10 ft. Vessel costs used, based on estimates from private industry, were calculated for wastes decayed 120 days and 1, 3, 10, and 30 years after reactor discharge prior to calcination. Aging had negligible effect on costs, except as it permitted larger diameter vessels to be used, because vessel and operating costs were much larger than capital costs in all cases. The lowest cost was 0.87 x 10/sup -2/ mill/kwh/sub e/ for processing acidic Purex and Thorex wastes in 24-in.-dia vessels, and the highest was 5.0 x 10/sup -2/ mill/kwh/sub e/ for processing reacidified …

The simultaneous production of helium from (n,..cap alpha..) reactions and atomic displacement damage by energetic neutrons in reactor structural alloys is expected to have a strong influence on their irradiation response for first wall and structural applications in fusion power reactors. Charged particle bombardment offers the possibility of assessing the phenomenology and mechanisms of microstructural evolution in a wide range of materials exposed to simultaneous helium injection and creation of atomic displacement damage by a second ion beam. In this program two ion accelerators have been used to simultaneously focus a beam of helium ions and a second ion beam on targets of selected reactor structural alloys. The resulting microstructural changes have been studied for systematic variations in damage rate, irradiation temperature, fluence and appm helium/dpa ratio and compared and correlated with results from companion fission reactor and high energy neutron irradiation studies conducted elsewhere in the DOE program.

This month's issue has the following articles: (1) Simulating the Electromagnetic World--Commentary by Steven R. Patterson; (2) A Code to Model Electromagnetic Phenomena--EMSolve, a Livermore supercomputer code that simulates electromagnetic fields, is helping advance a wide range of research efforts; (3) Characterizing Virulent Pathogens--Livermore researchers are developing multiplexed assays for rapid detection of pathogens; (4) Imaging at the Atomic Level--A powerful new electron microscope at the Laboratory is resolving materials at the atomic level for the first time; (5) Scientists without Borders--Livermore scientists lend their expertise on peaceful nuclear applications to their counterparts in other countries; and (6) Probing Deep into the Nucleus--Edward Teller's contributions to the fast-growing fields of nuclear and particle physics were part of a physics golden age.

The 331 Life Sciences Laboratory Drain Field (LSLDF) septic system waste site consists of a diversion chamber, two septic tanks, a distribution box, and a drain field. This septic system was designed to receive sanitary waste water, from animal studies conducted in the 331-A and 331-B Buildings, for discharge into the soil column. However, field observations and testing suggest the 331 LSLDF septic system did not receive any discharges. In accordance with this evaluation, the confirmatory sampling results support a reclassification of the 331 LSLDF waste site to No Action. This site does not have a deep zone or other condition that would warrant an institutional control in accordance with the 300-FF-2 ROD under the industrial land use scenario.

We present a linear scaling 3 dimensional fragment (LS3DF)method that uses a novel decomposition and patching scheme to do abinitio density functional theory (DFT) calculations for large systems.This method cancels out the artificial boundary effects that arise fromthe spatial decomposition. As a result, the LS3DF results are essentiallythe same as the original full-system DFT results with errors smaller thanthe errors introduced by other sources of numerical approximations. Inaddition, the resulting computational times are thousands of timessmaller than conventional DFT methods, making calculations with 100,000atom systems possible. The LS3DF method is applicable to insulator andsemiconductor systems, which covers a current gap in the DOE's materialsscience code portfolio for large-scale ab initio simulations.

In 2000 and 2001, the Kalispel Natural Resource Department (KNRD) continued to mitigate the wildlife habitat losses as part of the Albeni Falls Wildlife Mitigation Project. Utilizing Bonneville Power Administration (BPA) funds, the Kalispel Tribe of Indians (Tribe) purchased three projects totaling nearly 1,200 acres. The Tacoma/Trimble Wildlife Management Area is a conglomeration of properties now estimated at 1,700 acres. It is the Tribe's intent to manage these properties in cooperation and collaboration with the Pend Oreille County Public Utility District (PUD) No. 1 and the U.S. Fish and Wildlife Service (USFWS) to benefit wildlife habitats and associated species, populations, and guilds.

None

Many of the important challenges facing humanity, including developing alternative sources of energy and improving heath, are being addressed by advances that demand the improved understanding and control of matter. While the visualization, exploration, and manipulation of macroscopic matter have long been technological goals, scientific developments in the twentieth century have focused attention on understanding matter on the atomic scale through the underlying framework of quantum mechanics. Of special interest is matter that consists of natural or artificial nanoscale building blocks defined either by atomic structural arrangements or by electron or spin formations created by collective correlation effects. The essence of the challenge to the scientific community has been expressed in five grand challenges for directing matter and energy recently formulated by the Basic Energy Sciences Advisory Committee. These challenges focus on increasing our understanding of, and ultimately control of, matter at the level of atoms, electrons. and spins, as illustrated in Figure 1.1. Meeting these challenges will require new tools that extend our reach into regions of higher spatial, temporal, and energy resolution. Since the fundamental interaction that holds matter together is of electromagnetic origin, it is intuitively clear that electromagnetic radiation is the critical tool in the study …

We demonstrate the limitations of using retarded (bisulfite) developer to abate film sensitivity of x-ray films that have been exposed to intense radiation. We compared the measured densities of a large number of Kodak Type-M x-ray film samples exposed to a known fluence of monochromatic x-rays. These film samples were processed in three separate batches of bisulfite developer mixed in the same proportions. We concluded that reproducible film-density information cannot be obtained using different batches of (bisulfite) developer solutions.

The influence of hydrogen on fatigue life of niobium and vanadium is described. In tests carried out under stress control conditions on unnotched material hydrogen extends fatigue life of both metals. However, in stress controlled tests on notched bars and in strain control tests on unnotched bars hydrogen is detrimental to fatigue life. Hydrided alloys are much more sensitive to notches than are the unalloyed metals. Frequency effects on fatigue life also are much more severe in hydrided alloys, lower frequency leading to shorter life. The results of delayed failure, creep tests and elevated temperature fatigue tests also are reported. Niobium and vanadium reveal reduced fatigue lives at elevated temperatures for tests carried out in vacuum. The results of limited hold time and low frequency tests on strain controlled fatigue life also are reported. Increasing hold time increases fatigue life of niobium in the range 450 to 650/sup 0/C. Fractographic features change from striations in unalloyed metals to cleavage in the hydrided alloys tested at room temperature.

The purpose of this writeup is to supplement the publication, Massively Parallel Fokker-Planck Calculations,'' which appeared in the Proceedings of the Fifth Distributed Memory Computing Conference. Results obtained subsequent to that presentation are reported. This work is not self-contained; the reader should refer to that publication.

Bethlehem Steel Corporation (BSC), in conjunction with the Department of Energy (DOE) is conducting a Clean Coal Technology (CCT) project at its Sparrows Point, Maryland Coke Oven Plant. This project combines several existing technologies into an integrated system for removing impurities from Coke Oven Gas (COG) to make it an acceptable fuel. DOE is providing cost-sharing under a Cooperative Agreement with BSC. This Cooperative Agreement requires BSC to develop and conduct an Environmental Monitoring Plan (EMP) for the Clean Coal Technology project and to report the status of the EMP on a quarterly basis. This report is the third quarterly status report of the EMP. It covers the Environmental Monitoring Plan activities for the full year of 1991 from January 1, 1991 through December 31, 1991, including the forth quarter. See Sections 2, 3 and 4 for status reports of the Project Installation and Commissioning, the Environmental Monitoring activities and the Compliance Monitoring results for the period. Section 5 contains a list of Compliance Reports submitted to regulatory agencies during the period. The EMP describes in detail the environmental monitoring activities to be performed during the project execution. The purpose of the EMP is to: (1) document the extent of …

The Notre Dame Radiation Laboratory is a facility of the Department of Energy operated for DOE by the University of Notre Dame. The majority of the programs within the Laboratory are supported by the Office of Basic Energy Sciences of DOE and, unless otherwise noted in the following, support can be attributed to the Office of Basic Energy Sciences. Certain additional programs, so indicated, are supported by the Office of Standard Reference Data of the National Institute of Standards and Technology. Research programs conducted at the laboratory are briefly described.

The US program in high energy physics from 1985 to 1995 is reviewed. The program depends primarily upon work at the national accelerator centers, but includes a modest but diversified nonaccelerator program. Involvement of universities is described. International cooperation in high energy physics is discussed, including the European, Japanese, USSR, and the People's Republic of China's programs. Finally, new facilities needed by the US high energy physics program are discussed, with particular emphasis given to a Superconducting Super Collider for achieving ever higher energies in the 20 TeV range. (LEW)

To participate in the 1990 CORA Workshop at Kernforschungszentrum Karlsruhe (KfK) GmbH, Karlsruhe, FRG, on October 1--4, and to participate in detailed discussions on October 5 with the KfK CORA Boiling Water Reactor (BWR) experiments. The traveler attended the 1990 CORA Workshop at KfK, FRG. Participation included the presentation of a paper on work performed by the Boiling Water Reactor Core Melt Progression Phenomena Program at Oak Ridge National Laboratory (ORNL) on posttest analyses of CORA BWR experiments. The Statement of Work (November 1989) for the BWR Core Melt Progression Phenomena Program provides for pretest and posttest analyses of the BWR CORA experiments performed at KfK. Additionally, it is intended that ORNL personnel participate in the planning process for future CORA BWR experiments. For these purposes, meetings were held with KfK staff to discuss such topics as (1) experimental test schedule, (2) BWR test conduct, (3) perceived BWR experimental needs, and (4) KfK operational staff needs with respect to ORNL support. 19 refs.

This progress report is for the September--October 1991 quarter. We have demonstrated feasibility of higher specific conductance by a factor of five than any other work in high-temperature gas-to-gas exchangers. These laminar-flow, microtube exchangers exhibit extremely low pressure drop compared to alternative compact designs under similar conditions because of their much shorter flow length and larger total flow area for lower flow velocities. The design appears to be amenable to mass production techniques, but considerable process development remains. The reduction in materials usage and the improved heat exchanger performance promise to be of enormous significance in advanced engine designs and in cryogenics.

Bethlehem Steel Corporation (BSC), in conjunction with the Department of Energy (DOE) is conducting a Clean Coal Technology (CCT) project at its Sparrows Point, Maryland Coke Oven Plant. This project combines several existing technologies into an integrated system for removing impurities from Coke Oven Gas (COG) to make it an acceptable fuel. DOE is providing cost-sharing under a Cooperative Agreement with BSC. This Cooperative Agreement requires BSC to develop and conduct an Environmental Monitoring Plan (EMP) for the Clean Coal Technology project and to report the status of the EMP on a quarterly basis. This report is the third quarterly status report of the EMP. It covers the Environmental Monitoring Plan activities for the full year of 1991 from January 1, 1991 through December 31, 1991, including the forth quarter. See Sections 2, 3 and 4 for status reports of the Project Installation and Commissioning, the Environmental Monitoring activities and the Compliance Monitoring results for the period. Section 5 contains a list of Compliance Reports submitted to regulatory agencies during the period. The EMP describes in detail the environmental monitoring activities to be performed during the project execution. The purpose of the EMP is to: (1) document the extent of …

This is the monthly report for the Hanford Laboratories Operation September 1961. Reactor fuels, chemistry, dosimetry, separation processes, reactor technology, financial activities, biology operation, physics and instrumentation research, operations research and synthesis, programming, and radiation protection operation are discussed.

The purpose of the test described in this report is to set an upper limit on shadowing of the DR Reactor vertical safety system control strength by residual boron-steel balls in the graphite stack. Such an experimental determination should permit less stringent total control requirements than those based presently on necessarily conservative assumptions.

In 2000, PNNL conducted a two-year study for the U.S. Army Corps of Engineers to investigate energy use and swimming performance of adult spring chinook salmon (Oncorhynchus tshawystcha) migrating upstream through a large hydropower dam on the Columbia River. The investigation involved one year of laboratory study and one year of field study at Bonneville Dam. The objectives of the laboratory study were to 1) measure active rates of oxygen consumption of adult spring chinook salmon at three water temperatures over a range of swimming speeds; 2) estimate the upper critical swimming speed (Ucrit) of adult spring chinook salmon; and 3) monitor electromyograms (EMGs) of red and white muscle in the salmon over a range of swimming speeds. Laboratory results showed rate of oxygen consumption and red and white muscle activity in adult spring chinook salmon were strongly correlated with swimming speed over a range of fish sizes and at three different temperatures. In the field studies at Bonneville Dam, EMG radiotelemetry was used to examine the amount of energy spring chinook salmon expend while migrating upstream past the dam?s tailraces, fishways, and forebays. Aerobic and anaerobic energy use rates were determined. Energy use was estimated for different specific sections …