Chalcogen-rich transition-metal dichalcogenide (TMD) magnetron sputtering targets were custom manufactured via ball milling and sintering in the interest of depositing p-type chalcogen-rich films. Room temperature radio frequency (RF) magnetron sputtering produced ultra-thin amorphous precursor of WSx and MoSx (where x is between 2-3) on several different substrates. The influence of working pressure on the MoS3 content of the amorphous films was explored with X-ray photoelectron spectroscopy (XPS), while the physical and chemical effects of sputtering were investigated for the WSx target itself. The amorphous precursor films with higher chalcogenide content were chosen for laser annealing, and their subsequent laser annealing induced phase transformations were investigated for the synthesis of polycrystalline 2H-phase semiconducting thin films. The role of laser fluence and the number of laser pulses during annealing on phase transformation and film mobility was determined from Raman spectroscopy and Hall effect measurement, respectively. Hall effect measurements were used to identify carrier type and track mobility between amorphous precursors and crystalline films. The p-type 2H-TMD films demonstrates the ability to produce a scalable processing criterion for quality ultra-thin TMD films on various substrates and in a method which is also compatible for flexible, stretchable, transparent, and bendable substrates.

To design high pressure fuel system components that resist wear and scuffing failure when operated in low viscosity fuels, a comprehensive study on the tribological performance of various existing coating materials is necessary. This thesis aims to provide the relative performance of a variety of coating materials across different fuel environments by testing them in conditions that model those experienced in fuel pumps. The relative performance of these coatings are then indexed across a variety of material properties, including hardness, elastic modulus, wettability, and the interaction between the surface and the various types of fuel molecules.

In this study, we observed the effects of the processing-induced method on two different shape memory alloys (SMAs). First, we compare the transformation behavior of a martensitic NiTi SMA during thermal cycling using wide angle synchrotron radiation X-ray diffraction (WAXS). Based on the thermal cycling results, three observations about processing-induced SGAs as compared to SMAs can be seen: (1) retention of distorted austenite at high and low temperatures, (2) broadening of diffraction peaks in WAXS and disappearance of the thermal peaks in DSC measurements both due to induced strain, and (3) gradual increase in the amount of the martensitic phase. Second, we applied a processing-induced method to a FeMnAlCrNi alloy to examine the possibility of forming a strain glass alloy in an Fe-based system through sufficient dislocation formation via plastic deformation. This alloy was subjected to various percentages of cold work and characterized using scanning electron microscopy, differential scanning calorimetry, Vickers hardness, WAXS data. The results indicate with 50% thickness reduction, stress-free thermal cycling no longer exhibits a measurable phase transformation, suggesting the successful formation of strain glass alloy through sufficient dislocation. The results of this research contribute significantly to the advancement of strain glass alloys (SGAs), especially with respect …

In this study, four different NiTi-based shape memory alloys (SMAs) compositions were processed, shape-set, and characterized to evaluate their effectiveness as SMA actuation component for satellite antennas. Three of the compositions were commercially available NiTi wires (90°C Flexinol® actuator NiTi wire and Confluent ADB SE508 NiTi wire), NiTi SM495 plates (ATI Specialty Alloys and Components) and the other composition was in house lab-produced NiTiCu plate. Different shape-setting techniques were performed such as pin and plate, fixtures and dies, and finally a sandwich fixture. The two most promising outcomes were the SE NiTi 508 wire and the NiTiCu plate. A SE NiTi 508 wire was first heat-treated at 550 °C for 3 hours and then it was shape-set at 450 °C for 30 min using a Cu tube which was previously deformed to the desired deployment curvature and fixed on a steel rig. The wire was kept inside the Cu tube during the shape-setting process to obtain the desired curvature. After shape-setting, the wire was thermally cycled multiple times. The results showed that the SE NiTi 508 wire was able to retain its deployment shape successfully after each thermal cycle. Furthermore, a NiTiCu plate was sandwiched between two steel sheets which …

Shape memory alloys (SMAs) have gained much attention as a powerful source of actuation due to their improved performance, reduced size, and reduced complexity between components as well as having a high work output density. Their primary mechanism of actuation relies on a non-diffusional cyclic phase transformation from martensite to austenite, where the amount of thermal energy needed per cycle is directly associated with the hysteresis width between the austenite final and martensite final temperatures. Consequently, a narrower gap between those two temperature ranges requires a much lower energy demand to produce the actuation needed. Previous studies have indicated that the hysteresis width is linked to a strong coherence between the austenite/martensite interface. It has been shown that elemental additions to NiTi-based SMAs can further improve this coherency. Another huge challenge facing this unique technology is linked with its thermo-mechanical stability. Binary NiTi SMAs often exhibit significant transformation temperature shifts after each thermo-mechanical cycle, which can contribute to a shorter lifespan. The primary goal of this project is to identify and develop thermo-mechanically stable, low hysteresis shape memory alloys (LHSMAs) for actuator applications. To accomplish this goal, elemental additions of Cu, Co, Hf, and Pd were incorporated into NiTi-based SMAs …

Traditional lightweight armor ceramics such as boron carbide (B4C) and silicon carbide (SiC) are used alone or together in varying amounts to create monolithic protective plates. These materials exhibit relatively small differences in hardness, flexure strength, and fracture toughness. Many of the routes taken during the synthesis of the powder and sintering of the plates using traditional ceramic processing techniques have long processing times, tend to leave asperities within the microstructure, and have unwanted secondary phases that lower the performance of these materials. In lieu of the incremental changes in the above properties, it is thought that adding diamond particulates to the ceramic matrix will dramatically improve the mechanical properties and overall performance. With the reduced cost of synthetic diamond and the commercial development of more rapid spark plasma sintering (SPS), this work develops a novel reactive SPS process to fabricate near fully dense SiC-TiC-diamond composites at various processing temperatures with minimal graphitization and full adhesion to the ceramic matrix. It was found that samples with up to ~97% theoretical density can be fabricated with no quantifiable graphite content within the characterization ability using advanced X-ray diffraction and microscopy techniques.

Current ways to alter the microstructure of materials are usually through heat treatments, alloying, and other physical metallurgical methods. Recent efforts in the 21st century are focused on altering the microstructure of a material without physical contact which can be achieved through exposure to a magnetic field (MF). The motivation of this research is to study the quantum effects by subjecting solid-state metals to exposure of MFs. Many of the popular metals currently used in industry are paramagnetic. The ability to alter the microstructure and thus properties of these paramagnetic materials through a magnetic field would open new avenues to the field of research, including, potentially, a pollution-free, non-contact route. The effects of a magnetic field on the mechanical properties of paramagnetic materials were observed through compression testing of the pure paramagnetic material samples induced in a magnetic field. XRD and PPMS were used to relate flow stress to dislocation density and magnetic property of the samples when exposed to the presence of a static magnetic field. The effects of a magnetic field relative to alloyed paramagnetic materials were observed through the same procedure as pure paramagnetic elements. For this purpose, -Ti alloys were chosen as literature suggests a phase …

Magnetic field-assisted freeze-casting was used to create porous B4C ceramic preforms. An optimum slurry consisted of a mixture of B4C powders with 6 wt.% Er2O3 powder in an H2O-PVA solution and was cooled at a rate of 1 °C/min from room temperature to -30 °C resulting in porous green state ceramic preform with vertical channels. The Er2O3 powder was added to improve the magnetic response of the slurry. The preform was then sublimated to remove H2O and then sintered. The sintered ceramic preform was then infiltrated in the most vertically aligned channel direction with molten Al (A356) metal through a vacuum-assisted pump to create the metal matrix composite (MMC). Finite element analysis simulations were used to analyze and predict the anisotropic effect of B4C channel alignment on mechanical properties. The mechanical properties of the composite were then experimentally found via compression testing, which was compared with rule-of-mixtures and finite element modeling simulations, to analyze the effect of anisotropy due to magnetic field-assisted freeze-casting. This study reinforces the viability of cost-effective magnetic field-assisted freeze-casting as a method to create highly directional ceramic preforms, which can be subsequently metal infiltrated to produce MMCs with highly anisotropic toughness.

Complex concentrated alloys (CCAs) offer the unique ability to tune composition and microstructure to achieve a wide range of mechanical performance. Recently, the development of metastable CCAs has led to the creation of transformation-induced plasticity (TRIP) CCAs. Similar to TRIP steels, TRIP CCAs are more effective at absorbing high strain rate loads when TRIP is activated during the loading process. The objective of our study is to investigate the effect of copper on the critical pressure for activating TRIP and the high pressure stability of a Fe(40-X)Mn20Cr15Co20Si5CuX TRIP CCA, where x varies from 0 to 3 at.% Cu. To achieve this goal, diamond anvil cell testing during in-situ synchrotron radiation X-ray diffraction was performed using both a monochromatic wide angle X-ray scattering (WAXS) beam and, for the first time ever, a polychromatic Laue diffraction beam on a CCA. Laue diffraction allows for real-time phase evolution tracking of the γ-fcc → ε-hcp transformation in a high pressure environment. Based on the results, a new method for processing and preparation of high pressure samples without changing the microstructure of sample was developed. This new method can be used to prepare any CCA samples for high pressure testing.

Bioactive glass is a type of third generation bioactive material that can bond to both soft and hard tissue with applications ranging from bone defect repair, coatings for metallic implants, to scaffolds for tissue engineering. Design of bioactive glasses for these applications rely on a detailed understanding of the structures of these glasses which are complicated and multicomponent. In this thesis, I have applied molecular dynamics (MD) simulations with interatomic potentials developed in our group to understand the effect of modifier cation substitution on the structures and properties of two series of bioactive glasses. Particularly, MD simulations are used to understand K2O to Na2O and MgO to CaO substitution on the short and medium range structures (such as cation coordination number, pair distribution function, Qn distribution, and ring size distribution) and properties (such as bulk and Young's moduli and CTE) of 55S4.1 bioactive glasses. As Na2O is incrementally substituted with K2O in 55S4.1, a decrease of the glass transition temperature (Tg) and an increase of CTE was observed, as well as a decreasing trend in the moduli. For the MgO to CaO substitution series, Mg2+ is mainly four-fold coordinated that suggests that it can play a role as a network …