As one of the most critical system for RHIC operation, the beam abort kicker system has to be highly available, reliable, and stable for the entire operating range. Along with the RHIC commission and operation, consistent efforts have been spend to cope with immediate issues as well as inherited design issues. Major design changes have been implemented to achieve the higher operating voltage, longer high voltage hold-off time, fast retriggering and redundant triggering, and improved system protection, etc. Recent system test has demonstrated for the first time that both blue ring and yellow ring beam abort systems have achieved more than 24 hours hold off time at desired operating voltage. In this paper, we report break down, thyratron reverse arcing, and to build a fast re-trigger system to reduce beam spreading in event of premature discharge.

We used synthetic aperture radar interferograms to image ground subsidence that occurred over the Dixie Valley geothermal field during different time intervals between 1992 and 1997. Linear elastic inversion of the subsidence that occurred between April, 1996 and March, 1997 revealed that the dominant sources of deformation during this time period were large changes in fluid volumes at shallow depths within the valley fill above the reservoir. The distributions of subsidence and subsurface volume change support a model in which reduction in pressure and volume of hot water discharging into the valley fill from localized upflow along the Stillwater range frontal fault is caused by drawdown within the upflow zone resulting from geothermal production. Our results also suggest that an additional source of fluid volume reduction in the shallow valley fill might be similar drawdown within piedmont fault zones. Shallow groundwater flow in the vicinity of the field appears to be controlled on the NW by a mapped fault and to the SW by a lineament of as yet unknown origin.

A source evaluation case study is presented for observations of algae toxicity in an intermittent stream passing through the Lawrence Livermore National Laboratory near Livermore, California. A five-step procedure is discussed to determine the cause of water toxicity problems and to determine appropriate environmental management practices. Using this approach, an upstream electrical transfer station was identified as the probable source of herbicides causing the toxicity. In addition, an analytical solution for solute transport in overland flow was used to estimate the application level of 40 Kg/ha. Finally, this source investigation demonstrates that pesticides can impact stream water quality regardless of application within levels suggested on manufacturer labels. Environmental managers need to ensure that pesticides that could harm aquatic organisms (including algae) not be used within close proximity to streams or storm drainages and that application timing should be considered for environmental protection.

The current waste package design for the proposed repository at Yucca Mountain Nevada, USA, employs gas tungsten arc welding (GTAW) in fabricating the waste packages. While GTAW is widely used in industry for many applications, it requires multiple weld passes. By comparison, single-pass welding methods inherently use lower heat input than multi-pass welding methods which results in lower levels of weld distortion and also narrower regions of residual stresses at the weld TWI Ltd. has developed a Reduced Pressure Electron Beam (RPEB) welding process which allows EB welding in a reduced pressure environment ({le} 1 mbar). As it is a single-pass welding technique, use of RPEB welding could (1) achieve a comparable or better materials performance and (2) lead to potential cost savings in the waste package manufacturing as compared to GTAW. Results will be presented on the initial evaluation of the RPEB welding on a Ni-Cr-Mo alloy (a candidate alloy for the Yucca Mountain waste packages) in the areas of (a) design and manufacturing simplifications, (b) material performance and (c) weld reliability.

Facilities to support development of modified nitride-based reactor fuel pellets have been activated and are now in operation at Lawrence Livermore National Laboratory. These facilities provide the controls and monitored laboratory conditions required to produce, evaluate, and verify quality of the nitride-based product required for this fuel application. By preserving the high melting point, high thermal conductivity, and high actinide density properties of nitride fuel while enhancing stoichiometry, density, and grain structure, and by applying inert matrix (ZrN) and neutron absorbing (HfN) additives for improved stability and burn-up characteristics, the requirements for a long-life fuel to support sealed core reactor applications may be met. This paper discusses requirements for producing the modified nitride powders for sintering of fuel pellets, translation of these requirements into facility specifications, and implementation of these specifications as facility capabilities.

This paper discusses issues with the limited precision of hardware-based volume visualization. We will describe the compositing OVER operator and how fixed-point arithmetic affects it. We propose two techniques to improve the precision of fixed-point compositing and the accuracy of hardware-based volume visualization. The first technique is to perform dithering of color and alpha values. The second technique we call exponent-factoring, and captures significantly more numeric resolution than dithering, but can only produce monochromatic images.

This report is a summary of the discussion sessions of the 12th Workshop on Crystalline Silicon Solar Cells and Processes. The theme of the workshop was"Fundamental R&D in c-Si: Enabling Progress in Solar-Electric Technology." This theme was chosen to reflect a concern that the current expansion in the PV energy production may redirect basic research efforts to production-oriented issues. The PV industry is installing added production capacity and new production lines that include the latest technologies. Once the technologies are selected, it is difficult to make changes. Consequently, a large expansion can stagnate the technologies and diminish interest in fundamental research. To prevent the fundamental R&D program from being overwhelmed by the desire to address immediate engineering issues, there is a need to establish topics of fundamental nature that can be pursued by the universities and the research institutions. Hence, one of the objectives of the workshop was to identify such areas for fundamental research.

Positronium (Ps) is simulated using Path Integral Monte Carlo (PIMC). This method can reproduce the results of previous simple theories in which a single quantum particle is used to represent Ps within an idealized pore. In addition, the calculations treat the e{sup -} and e{sup +} of Ps exactly and realistically model interactions with solid atoms, thereby correcting and extending the simpler theory. They study the pick-off lifetime of o-Ps and the internal contact density, {kappa}, which controls the self-annihilation behavior, for Ps in model voids (spherical pores), defects in a solid (argon), and microporous solids (zeolites).

A future muon collider or neutrino factory requires fast acceleration to minimize muon decay. We have previously described an FFAG ring that accelerated muons from 10 to 20 GeV in energy. The ring achieved its large momentum acceptance using a low-emittance lattice with a small dispersion. In this paper, we present an update on that ring. We have used design tools that more accurately represent the ring's behavior at large momentum offsets. We have also improved the dynamic aperture from the earlier design.

Space debris constitutes a significant hazard to low earth orbit satellites and particularly to manned spacecraft. A quite small velocity decrease from vaporization impulses is enough to lower the perigee of the debris sufficiently for atmospheric drag to de-orbit the debris. A short pulse (picosecond) laser version of the Orion concept can accomplish this task in several years of operation. The ''Mercury'' short pulse Yb:S-FAP laser being developed at LLNL for laser fusion is appropriate for this task.

During the summer of 2002, eight superconducting helical spin rotators were installed into RHIC in order to control the polarization directions independently at the STAR and PHENIX experiments. Without the rotators, the orientation of polarization at the interaction points would only be vertical. With four rotators around each of the two experiments, we can rotate either or both beams from vertical into the horizontal plane through the interaction region and then back to vertical on the other side. This allows independent control for each beam with vertical, longitudinal, or radial polarization at the experiment. In this paper, we present results from the first run using the new spin rotators at PHENIX.

None

Prevention of the introduction of fissile materials into international shipping, and hence into a given country, is a complex problem. Some pieces of the solution to the puzzle are conceptually well defined, but lack definition of a technical pathway and/or operational implementation. Other elements are a little more fuzzy, and some elements are probably undefined at this point in time. This paper reviews the status of the more well-defined elements, and suggests needed additional measures to enhance the probability that fissile materials are not illicitly introduced into distant countries. International commerce proceeds through a number of steps from point of origin to final destination. Each step offers the possibility of a well-defined choke point to monitor and interdict the illicit shipment of fissile materials. However, because there are so many potential points and venues of entry into a large country such as the United States (e.g., air cargo, shipping containers, truck and rail transport, private vehicles, boats and planes, commercial passenger travel), it behooves the world to ensure that fissile material does not illicitly leave its point of origin.

The authors have used a study of the process e{sup +}e{sup -} {yields} {mu}{sup +}{mu}{sup -} {gamma} at a center-of-mass energy near the {Upsilon}(4S) resonance for a {mu}{sup +}{mu}{sup -} invariant mass range near the J/{psi} mass to extract the cross section {sigma}(e{sup +}e{sup -} {yields} J/{psi}{gamma} {yields} {mu}{sup +}{mu}{sup -}{gamma}). The data set, corresponding to an integrated luminosity of 88.4 fb{sup -1}, was collected using the BABAR detector at the PEP-II collider. They measure the product {Lambda}(J/{psi} {yields} e{sup +}e{sup -}) B(J/{psi} {yields} {mu}{sup +}{mu}{sup -}) to be 0.330 {+-} 0.008 {+-} 0.007 keV. Using the world averages for B(J/{psi} {yields} {mu}{sup +}{mu}{sup -}) and B(J/{psi} {yields} e{sup +}e{sup -}), they derive the J/{psi} electronic and total widths: {Lambda}(J/{psi} {yields} e{sup +}e{sup -}) = 5.61 {+-} 0.20 keV and {Lambda} = 94.7 {+-} 4.4 keV.

None

Based on annual tritium release rates from the five sources of tritium at Lawrence Livermore National Laboratory and the Tritium Research Laboratory at Sandia National Laboratory, the regulatory dispersion and dose model, CAP88-PC, was used to predict tritium concentrations in air at perimeter and offsite air surveillance monitoring locations for 1986 through 2001. These predictions were compared with mean annual measured concentrations, based on biweekly sampling. Deterministic predictions were compared with deterministic observations using predicted-to-observed ratios. In addition, the uncertainty on observations and predictions was assessed: when the uncertainty bounds of the observations overlapped with the uncertainty bounds of the predictions, the predictions were assumed to agree with the observations with high probability. Deterministically, 54% of all predictions were higher than the observations, and 96% fell within a factor of three. Accounting for uncertainty, 75% of all predictions agreed with the observations; 87% of the predictions either matched or exceeded the observations. Predictions equaled or exceeded observations at those sampling locations towards which the wind blows most frequently, except those in the hills. Under-predictions were seen at locations towards which the wind blows infrequently when released tritium was from elevated sources. When a high fraction of tritium was from area …

We present a new x-ray detection technique based on optical measurement of the effects of x-ray absorption and electron hole pair creation in a direct band-gap semiconductor. The electron-hole pairs create a frequency dependent shift in optical refractive index and absorption. This is sensed by simultaneously directing an optical carrier beam through the same volume of semiconducting medium that has experienced an xray induced modulation in the electron-hole population. If the operating wavelength of the optical carrier beam is chosen to be close to the semiconductor band-edge, the optical carrier will be modulated significantly in phase and amplitude. This approach should be simultaneously capable of very high sensitivity and excellent temporal response, even in the difficult high-energy xray regime. At xray photon energies near 10 keV and higher, we believe that sub-picosecond temporal responses are possible with near single xray photon sensitivity. The approach also allows for the convenient and EMI robust transport of high-bandwidth information via fiber optics. Furthermore, the technology can be scaled to imaging applications. The basic physics of the detector, implementation considerations, and preliminary experimental data are presented and discussed.

We summarize results of several successful dense plasma diagnostics experiments realized by combining two different kinds of table-top soft x-ray lasers with an amplitude division interferometer based on diffraction grating beam splitters. In the first set of experiments this robust high throughput diffraction grating interferometer (DGI) was used with a 46.9 nm portable capillary discharge laser to study the dynamics of line focus and point focus laser-created plasmas. The measured electron density profiles, which differ significantly from those expected from a classical expansion, unveil important two-dimensional effects of the dynamics of these plasmas. A second DGI customized to operate in combination with a 14.7 nm Ni-like Pd transient gain laser was used to perform interferometry of line focus laser-created plasmas with picosecond time resolution. These measurements provide valuable new benchmarks for complex hydrodynamic codes and help bring new understanding of the dynamics of dense plasmas. The instrumentation and methodology we describe is scalable to significantly shorter wavelengths, and constitutes a promising scheme for extending interferometry to the study of very dense plasmas such as those investigated for inertial confinement fusion.

Alloy 22 (UNS N60622) is a nickel-based alloy, which is extensively used in aggressive industrial applications, especially due to its resistance to localized corrosion and stress corrosion cracking in high chloride environments. The purpose of this work was to characterize the anodic behavior of Alloy 22 in concentrated calcium chloride (CaCl{sub 2}) brines and to evaluate the inhibitive effect of nitrate, especially to localized corrosion. Standard electrochemical tests such as polarization resistance and cyclic polarization were used. Results show that the corrosion potential of Alloy 22 was approximately -360 mV in the silver-silver chloride (SSC) scale and independent of the tested temperature. Cyclic polarization tests showed that Alloy 22 was mainly susceptible to localized attack in 5 M CaCl{sub 2} at 75 C and higher temperatures. The addition of nitrate in a molar ratio of chloride to nitrate equal to 10 increased the onset of localized corrosion to approximately 105 C. The addition of nitrate to the solution also decreased the uniform corrosion rate and the passive current of the alloy.

A novel method for determining the equation-of-state (EOS) along the release isentrope in an isochoric (constant volume) heated plasma is presented. The sensitivity of this approach is demonstrated using two different equation-of-state models for a solid density, 10 eV expanding Al plasma. Determining the material EOS data is validated to pressures near 80 Mbar, much higher than current isentropic compression experiments allow. Limitations at high temperature (T{sub e} {ge} 100 eV) due to the formation of a radiative conduction layer near the rarefaction interface are also illustrated.

None

Nuclear materials were first used to end the World War II. They were produced and maintained during the cold war for global security reasons. In the succeeding 50 years since the Atoms for Peace Initiative, nuclear materials were produced and used in global civilian reactors and fuel cycles intended for peaceful purposes. The Nonproliferation Treaty (NPT) of 1970 established a framework for appropriate applications of both defense and civilian nuclear activities by nuclear weapons states and non-nuclear weapons states. As global inventories of nuclear materials continue to grow, in a diverse and dynamically changing manner, it is time to evaluate current and future trends and needed actions: what are the current circumstances, what has been done to date, what has worked and what hasn't? The aim is to identify mutually reinforcing programmatic directions, leading to global partnerships that measurably enhance international security. Essential elements are material protection, control and accountability (MPC&A) of separated nuclear materials, interim storage, and geologic repositories for all nuclear materials destined for final disposal. Cooperation among key partners, such as the MPC&A program between the U.S. and Russia for nuclear materials from dismantled weapons, is necessary for interim storage and final disposal of nuclear materials. Such …

Superovulation of female mice with exogenous gonadotrophins is routinely used for increasing the number of eggs ovulated by each female in reproductive and developmental studies. We report an unusual effect of superovulation on fertilization in mice. In vivo matings of superovulated T-stock females with B6C3F1 males resulted in a 2-fold reduction (P<0.001) in the frequencies of fertilized eggs compared to control B6C3F1 matings. In addition, {approx}22 hr after mating only 15% of fertilized eggs recovered in T-stock females had reached the metaphase stage of the first cleavage division versus 87% in B6C3F1 females (P < 0.0001). Matings with T-stock males did not improve the reproductive performance of T-stock females. To investigate the possible cause(s) for the impaired fertilization and zygotic development, the experiments were repeated using in vitro fertilization. Under these conditions, the frequencies of fertilized eggs were not different in superovulated T-stock and B6C3F1 females (51.7% {+-} 6.0 and 64.5% {+-}3.8, P=0.10). There was a 7-fold increase in the frequencies of fertilized T-stock eggs that completed the first cell cycle of development after in vitro versus in vivo fertilization. These results rule out an intrinsic deficiency of the T-stock oocyte as the main reason for the impaired fertility after …

Enhancing the proliferation resistance of nuclear energy systems and fuel cycles is an ambitious undertaking. Current systems, dominated by the light water reactor fuel cycle are quite proliferation resistant. However, continued accumulations of plutonium in spent fuel and accumulations of separated plutonium resulting from reprocessing are eroding the proliferation resistance of today's nuclear energy systems. Alternatives to address these issues invariably involve making trade-offs among different proliferation risks and advantages. For example, thorium cycles reduce the quantity and quality of plutonium in spent fuel, but do so at the expense of increased fresh fuel enrichment and/or production of separable U233. Evaluation of these tradeoffs is difficult, as there are serious and significant differences of opinion regarding the relative merits and significance of the various risks of and barriers to proliferation from commercial nuclear power fuel cycles.