The performance of a jet power plant consisting of a compressor and a turbine is determined by the characteristic curves of these component parts and is controllable by the characteristics of the compressor and the turbine in relation to each other. The normal. output, overload, and throttled load of the Jet power plant are obtained on the basis of assumed straight-line characteristics.

"The shell shall be considered as a three-dimensional continuous medium; for the coordinate surface, the middle surface of the shell shall be assumed parallel to the bounding surfaces. Let alpha and beta be the curvilinear orthogonal coordinates of this surface, coinciding with the lines of principal curvatures, and gamma the distance along the normal from the point (alpha,beta) of the coordinate surface to any point (alpha, beta, gamma) of the shell" (p. 1).

"The present report presents as a supplement to the fourth report (available as ATI 5045, Air Materiel Command) in the series of investigations concerning the flow about ring-shaped cowlings further wind-tunnel measurements on inlet devices which are to show the influence of the radius of the nose of the cowling on the flow conditions. Moreover, a simple rule for the design of such arrangements, containing a hub in the interior, is suggested" (p. 1).

The investigations carried out in a previous report (NACA TM 1325) concerning the flow about ring-shaped cowlings were extended by taking a circulation about the cowling into consideration. The present second report treats bodies of infinite length with approximately smooth entrance. The circulation was caused by distributing vortex rings of constant density over a stream surface extending to infinity. Furthermore, the influence of a hub body on such cowlings was dealt with.

The equations of motion for an airplane penetrating a gust are derived using a few simplifying assumptions. Calculations of loads for different static longitudinal stability on two German airplane models, HC 45 and HS 122, are compared with flight tests. Good agreement is obtained between the trend of the flight tests and the calculated values; however no absolute comparison was possible between the flight tests and calculations.

Starting with the Love equations for bending of extensible shells, "principal stress states" are sought for a thin-walled rod of arbitrary but open cross section. Principal stress states exclude those local states arising from end conditions which damp out with distance from the ends. It is found that for rods of intermediate length, long enough to avoid local bending at a support, and short enough that elementary torsion and bending are not the most significant stress states, four principal states exist.

A comprehensive survey of the elastic modulus of binary alloys as a function of the concentration is presented. Alloys that form continuous solid solutions, limited solid solutions, eutectic alloys, and alloys with intermetallic phases are investigated. Systems having the most important structures have been examined to obtain criteria for the relation between lattice structure, type of binding, and elastic behavior.

Drag tests at zero lift have been made at Mach numbers from 0.7 to approximately 0.95 in the high speed wind tunnel of the Institute of Aerodynamics, ETH, Zurich, on a group of untapered wings of aspect ratio 3.25, having sweep angles of 0 degree and 35 degrees. For each sweep angle, a series of geometrically similar models was tested at a constant Reynolds number to provide a verification of computed tunnel blocking corrections. Tests were also made for wings having thickness ratios of 0.09 and 0.12 and the results compared with results predicted by von Karman's similarity law.

The present paper gives the results of measurements of the resistance of a plate placed parallel to the flow in the range of Reynolds numbers from 10 to 2300; in this range the resistance deviates from the formula of Blasius. The lower limit of validity of the Blasius formula is determined and also the increase in resistance at the edges parallel to the flow in the case of a plate of finite width.

The displacement effect of the boundary layer on the outer frictionless flow is discussed for both steady and unsteady flows. The analysis is restricted to cases in which the potential flow pressure distribution remains valid for the boundary-layer calculation. Formulas are given for the dependence of the pressure drag, friction drag, and total drag of circular cylinders on the time from the start of motion for cases in which the velocity varies as a power of the time. Formulas for the locations and for the time for the appearance of the separation point are given for two dimensional bodies of arbitrary shape.

Among the information presented are included displacement, momentum, and kinetic energy thicknesses, shearing stress distributions across boundary layer, and surface friction coefficients. The Gruschwitz method and its modifications are examined and tested. An energy theorem for the turbulent boundary layer is introduced and discussed but does not lead to a method for the prediction of the behavior of the turbulent boundary layer because relations for the shearing stress and the surface friction are lacking.

"A thorough understanding of the turbulent flow movements cannot be arrived at from investigations of the temporal mean values of the flows alone. Study of the fluctuation phenomena themselves is indispensable. Thus turbulence research entered a new promising stage when investigators started performing fluctuation measurements and basing theories on those measurements" (p. 1).

A comparatively rapid method is presented for determining theoretically the bending stresses of helicopter rotor blades in forward flight. The method is based on the analysis of the properties of a vibrating beam, and its uniqueness lies in the simple solution of the differential equation which governs the motion of the bent blades.