A prototype, Nb{sub 3}Sn superconducting magnet, utilizing a racetrack coil design has been built and tested. This magnet represents the first step in a recently implemented program to develop a high field, accelerator quality magnet. This magnet was constructed with coils wound from conductor developed for the ITER project, limiting the magnet to a field of 6-7 Tesla. Subsequent magnets in the program will utilize improved conductor, culminating in a magnet design capable of producing fields approaching 15 Tesla. The simple geometry is more suitable for the use of brittle superconductors necessary to eventually reach high field levels. In addition, fewer and simpler parts are used in fabricating these coils compared with the more conventional cosine theta cross section coils. The general fabrication steps, mechanical design and quench performance are discussed.

In the high field magnet program at Lawrence Berkeley National Laboratory, accelerator magnet prototypes are designed with epoxy impregnated niobium-tin and niobium-titanium superconductor. Accurate mechanical property values are essential for magnet mechanical design and prediction of conductor performance. Two key mean property values are measured on coil samples: modulus of elasticity (Young's modulus) and mean thermal contraction. Measurements are made in compression and are conducted in three orthogonal directions. Modulus of elasticity measurements are currently conducted at room temperature and the mean thermal contraction is measured from room temperature to liquid nitrogen temperature. Room temperature values are compared with values estimated using the individual coil components.

For high energy physics applications superconducting cables are subjected to large stresses and high magnetic fields during service. It is essential to know how these cables perform in these operating conditions. A loading fixture capable of applying loads of up to 700 kN has been developed by NHMFL for LBNL. This fixture permits uniform loading of straight cables over a 122 mm length in a split-pair solenoid in fields up to 12 T at 4.2 K. The first results from this system for Rutherford cables of internal-tin and modified jelly roll strand of Nb{sub 3}Sn produced by IGC and TWC showed that little permanent degradation occurs up to 210 MPa. However, the cable made from internal-tin strand showed a 40% reduction in K{sub c} at 11T and 210 MPa while a dable made from modified jelly roll material showed only a 15% reduction in I{sub c} at 11T and 185 MPa.

Anchorage and growth factor independence are cardinal features of the transformed phenotype. Although it is logical that the two pathways must be coregulated in normal tissues to maintain homeostasis, this has not been demonstrated directly. We showed previously that down-modulation of {beta}1-integrin signaling reverted the malignant behavior of a human breast tumor cell line (T4-2) derived from phenotypically normal cells (HMT-3522) and led to growth arrest in a threedimensional (3D) basement membrane assay in which the cells formed tissue-like acini (14). Here, we show that there is a bidirectional cross-modulation of {beta}1-integrin and epidermal growth factor receptor (EGFR) signaling via the mitogenactivated protein kinase (MAPK) pathway. The reciprocal modulation does not occur in monolayer (2D) cultures. Antibodymediated inhibition of either of these receptors in the tumor cells, or inhibition of MAPK kinase, induced a concomitant downregulation of both receptors, followed by growth-arrest and restoration of normal breast tissue morphogenesis. Crossmodulation and tissue morphogenesis were associated with attenuation of EGF-induced transient MAPK activation. To specifically test EGFR and {beta}1-integrin interdependency, EGFR was overexpressed in nonmalignant cells, leading to disruption of morphogenesis and a compensatory up-regulation of {beta}1-integrin expression, again only in 3D. Our results indicate that when breast cells are spatially …

An object-oriented design that provides flexibility in simulation codes is presented. This flexibility allows programmers freedom to easily change solution algorithms and discretization schemes as well as add new solver packages as they become available. Careful attention is paid to separating algorithm, data, and specific problem classes to provide for ease in changing any of these components. Furthermore, data structures are chosen so that each component works with data in a form best suited to its needs. Lastly, we present some experiences and comments on the tradeoffs involved with this design.

The authors discuss the design of hypre, an object-oriented library for the solution of extremely large sparse linear systems on parallel computers. The mathematical emphasis of hypre is on modern powerful and scalable preconditioners. The design of hypre allows it to be used as both a solver package and a framework for algorithm development. The object model used for hypre is more general and flexible than the current generation of solver libraries.

The compact multi-pass laser design and the extensive use of optical component assemblies as line replaceable units (LRU) are essential to achieve the cost efficiency of the National Ignition Facility design. These design philosophies require a new approach to start-up operation of the NIF 192-beam-line high-energy laser compared to existing fusion laser facilities. The limited access to the beam-line optics and the limited on-line verification and maintenance capability require that extensive component verification and alignment take place in off-line facilities before the LRUÕs are installed in the laser structure. We are developing a detailed plan for the start-up of the NIF facility. This plan includes systematic off-line component and LRU verification tests, LRU installation and prealignment, and sub-system acceptance tests, followed by a well defined set of operational test procedures to verify integrated performance. During integrated performance testing laser performance parameters of individual beam lines will be verified using a precision diagnostic system located in the NIF switchyard. If additional on-line calibration or performance testing is required, the LRU based architecture can accommodate the insertion of specialized in-line diagnostic LRUs at locations that require such additional testing during start-up. Multiple beam focal spot characteristics on disk targets in the NIF …

We explored the optimum conditions in modulation of the program temperature and sample preparation to obtain absolute values of heat capac- ity from quasi-isothermal measurements of temperature-modulated differen- tial scanning calorimetry. A Mettler-Toledo 820 calorimeter and Perkin-Elmer DSC 7 were used for this work, using saw-tooth modulation as well as sinu- soidal modulation. We adopted a simple model to analyze the temperature response of the calorimeters and calibrated the results more precisely.

None

Although the crystal field has a strong influence on the heavy fermion properties of CeAl{sub 3}, the parameters of the crystal field Hamiltonian have not been established. We present the results of an analysis of inelastic neutron scattering data on CeAl{sub 3} to resolve this issue. By combining the neutron scattering results with measurements of the single crystal magnetic susceptibility, we have obtained an unambiguous set of crystal field parameters in CeAl{sub 3}: B{sub 2}{sup 0} = (5.8 {+-} 0.2) x 10{sup {minus}2} meV and B{sub 4}{sup 0} = (2.3 {+-} 0.1) x 10{sup {minus}2} meV. The corresponding level scheme of the ground multiplet of the Ce{sup 3+} ion is characterized by a {Lambda}{sub 9} {vert_bar} {+-} 3/2> ground state doublet and two close-lying excited doublets {Lambda}{sub 8} {vert_bar} {+-} 5/2> and {Lambda}{sub 7} {vert_bar} {+-} 1/2> at an energy of {approximately} 6.4 meV at 20 K. A comparison of the crystal field parameters along the RAl{sub 3} (R = Ce, Pr and Nd) series of isostructural compounds shows that in CeAl{sub 3}, A{sub 2}{sup 0} <r{sup 2}> is an order of magnitude larger, and A{sub 4}{sup 0} <R{sup 4}> is three times larger, than in PrAl{sub 3} and NdAl{sub …

The development of detailed, regional wind-resource distributions and other pertinent wind resource characteristics (e.g., assessment maps and reliable estimates of seasonal, diurnal, and directional) is an important step in planning and accelerating the deployment of wind energy systems. This paper summarizes the approach and methods being used to conduct a wind energy resource assessment of Mongolia. The primary goals of this project are to develop a comprehensive wind energy resource atlas of Mongolia and to establish a wind measurement program in specific regions of Mongolia to identify prospective sites for wind energy projects and to help validate some of the wind resource estimates. The Mongolian wind resource atlas will include detailed, computerized wind power maps and other valuable wind resource characteristic information for the different regions of Mongolia.

Lithium batteries are typically constructed from a lithium cobalt oxide cathode and a carbon anode. We have investigated intermetallic anode materials based on tin, which can provide a high capacity at a slightly higher voltage (400 mV) than metallic lithium and thus reduce the safety concerns associated with the carbon anode. In particular, we have investigated the copper-tin system at around the composition Cu{sub 6}Sn{sub 5} and have determined the effect on cycling and capacity of electrodes with various ratios of copper to tin. Anode compositions that are slightly copper rich (Cu{sub 6}Sn{sub 4}) were found to exhibit greater utilization of the tin than those with the stoichiometric bronze ratio (Cu{sub 6}Sn{sub 5}) or those having a slight excess of tin (Cu{sub 6}Sn{sub 6}). The differences in electrochemical behavior are explained in terms of an inert matrix model.

In recent years, in-beam x-ray experiments supplied a vast amount of data on high-spin states in nuclei in the vicinity of {sup 100}Sn. The present contribution reviews spectroscopic information obtained recently for N {ge} 50 nuclei around {sup 100}Sn, with emphasis on isomer studies, and discusses selected results in the frame of the shell model.

An image-analysis system, based on commercially available data visualization software (IDL [1]), allows convenient interaction with image data while still providing calculated beam parameters at a rate of up to 2 Hz. Image data are transferred from the IOC to the workstation via EPICS [2] channel access. A custom EPICS record was created in order to overcome the channel access limit of 16k bytes per array. The user can conveniently calibrate optical transition radiation (OTR) and fluorescent screens, capture background images, acquire and average a series of images, and specify several other filtering and viewing options. The images can be saved in either IDL format or APS-standard format (SDDS [3]), allowing for rapid postprocessing of image data by numerous other software tools.

Values of w calculated from the divergence of minisodar (MS) and radar wind profiler (RWP) horizontal wind profiles were found to agree quite well for an equilateral triangle of measurement sites located at the Argonne Boundary Layer Experiments (ABLE) facility. Values of w averaged over the daytime within the mixed layer were on the order of 0.5 cm/s. Correcting for height differences of 60-100 m among the three measurement sites separated by 63 km was helpful, particularly during windy conditions. A regular output of daily or even hourly values from this network is possible. Upgrades to the ox RWP now being implemented will improve the near-surface radar estimates.

We have investigated the stability and microstructural transformability of the Bi-2223 phase in a silver-sheathed monofilament composite tape fabricated using fine-grained Bi{sub 1.7}Pb{sub 0.3}Sr{sub 1.9}Ca{sub 2.0}-Cu{sub 3.0}O{sub y} (Bi-2223) as the precursor powder. The fully formed Bi-2223 precursor was prepared using established procedures. The purpose of this study was to explore the prospects for growing textured, large-grain-size Bi-2223 from the fine-grained precursor by process parameter perturbations. These perturbations included thermal ramp up variations, programmed heat treatment temperature and oxygen pressure fluctuations, and parameter manipulations during cool-down. Our results show that the types of heat treatments used in conventional oxide-powder-in-tube (OPIT) processing do not facilitate Bi-2223 grain growth when the precursor powder is preconcerted Bi-2223. We also observed that the Bi-2223 partially. decomposed during conventional thermal ramp-up in 0.075 atm O{sub 2}, but that this decomposition can be inhibited by ramping up in a reduced oxygen pressure. A pathway was found for back-reacting the fine-grained Bi-2223 (to Bi-2212, Bi-2201 and nonsuperconducting secondary phases), then reforming large-grained Bi-2223 in a colony microstructure having some distinct differences from that produced during conventional OPIT processing.

Powder-in-tube (PIT) processing was used to fabricate multifilamentary Ag-clad Bi{sub 2}Sr{sub 2}Ca{sub 2}Cu{sub 3}O{sub y} (Bi-2223) superconductors for various electric power applications. Enhancements in the transport current properties of long lengths of multifilament tapes were achieved by increasing the packing density of the precursor powder, improving the mechanical deformation, and adjusting the cooling rate. The dependence of the critical current density on magnetic field and temperature for the optimally processed tapes was measured. J{sub c} was greater than 10{sup 4} (A/cm{sup 2}) at 20 K for magnetic field up to 3 T and parallel to the c-axis which is of interest for use in refrigerator coded magnets. An attempt was made to combine the good alignment of Bi-2223 grains in Ag-sheathed superconducting tapes to obtain high J{sub c} values at high temperature and low field, and good intrinsic pinning of YBa{sub 2}Cu{sub 3}O{sub 7{minus}d} (Y-123) thin film to maintain high J{sub c} values in high fields. A new composite multifilament tape was fabricated such that the central part contained Bi-2223 filaments, with the primary function of conducting the transport current. The central Bi-2223 filaments were surrounded by Y-123 thin film to shield the applied magnetic field and protect the Bi-2223 …

An S-band linear accelerator is the source of particles and front end of the Advanced Photon Source [1] injector. Additionally, it will be used to support a low-energy undulator test line (LEUTL) and to drive a free-electron laser (FEL). To provide maximum linac availability for all uses, an additional modulator-klystron subsystem has been built,and a waveguide-switching and distribution subsystem is now under construction. The combined subsystems provide a hot spare for any of the five S-band transmitters that power the lina cand have been given the additional function of powering an rf gun test stand whenever they are not otherwise needed. Design considerations for the waveguide-switching subsystem, topology selection, timing, control, and system protection provisions are described.

The Argonne Wakefield Accelerator group develops accelerating structures based on dielectric loaded waveguides. We use high charge short electron bunches to excite wakefields in dielectric loaded structures, and a second (low charge) beam to probe the wakefields left behind by the drive beam. We report measurements of beam parameters and also initial results of the dielectric loaded accelerating structures. We have studied acceleration of the probe beam in these structures and we have also made measurements on the RF pulses that are generated by the drive beam. Single drive bunches, as well as multiple bunches separated by an integer number of RF periods have been used to generate the accelerating wakefields.

It is sometimes necessary to deploy, transport and store weapons containing high explosives (HE) in proximity. Accident analyses of these activities may include nearby explosion scenarios in which fragments from an exploding (donor) weapon impact a second (acceptor) weapon. Weapon arrays are designed to miti- gate consequences to potential acceptor weapons, but unless initiation of an accep- tor's HE is impossible, outcomes such as detonation must be considered. This paper describes an approach for estimating upper bound probabilities for fragment- dominated scenarios in which outcomes are expected to be rare events. Other aspectsl,z of nearby explosion problems were addressed previously. An example scenario is as follows. A donor weapon is postulated to detonate, and fragments of the donor weapon casing are accelerated outward. Some of the fragments may strike a nearby acceptor weapon whose HE is protected by casing materials. Most impacts are not capable of initiating the acceptor's HE. However, a sufficiently large and fast fragment could produce a shock-to-detonation transi- tion (SDT), which will result in detonation of the acceptor. Our approach will work for other outcomes of fragment impact, but this discussion focuses on detonation. Experiments show that detonating weapons typically produce a distribution of casing fragment …

Our investigations of both new and field-aged photovoltaic modules have indicated that, in general, today's commercially available modules area highly reliable product. However, by using new test procedures, subtle failure mechanisms have also been identified that must be addressed in order to achieve 30-year module lifetimes. This paper summarizes diagnostic test procedures, results, and implications of in-depth investigations of the performance and durability characteristics of commercial modules after long-term field exposure. A collaborative effort with U.S. module manufacturers aimed at achieving 30-year module lifetimes is also described.

Polymer electrolyte fuel cells (PEFCs) are being actively developed worldwide for transportation applications. The fuel gas generated from reforming hydrocarbon fuels contains small amounts of CO (0.5-1 vol%), even after the water-gas shift reaction. Carbon monoxide is preferentially adsorbed on the platinum electrocatalyst in the PEFC, thus blocking the access of H{sub 2} to the surface of the catalyst and resulting in the degradation of the cell performance. Therefore, the CO concentration in the PBFC reformate must be reduced to a tolerable level of {le} 100 ppm (1). Catalytic preferential oxidation (2), anode air bleed (3), or a combination of the two can be used to reduce CO to trace levels, but their use in a dynamically varying system is problematic. We are developing a sorption process based on the reversible complex-forming and dissociation reactions of CO with Cu(I). These reactions are well documented in patent and literature (4,5).

The polymer electrolyte fuel cell (PEFC) is the primary candidate as the power source for light-duty transportation systems. On-board conversion of fuels (reforming) to supply the required hydrogen has the potential to provide the driving range that is typical of today's automobiles. Petroleum-derived fuels, gasoline or some distillate similar to it, are attractive because of their existing production, distribution, and retailing infrastructure. The fuel may be either petroleum-derived or other alternative fuels such as methanol, ethanol, natural gas, etc. [1]. The ability to use a variety of fuels is also attractive for stationary distributed power generation [2], such as in buildings, or for portable power in remote locations. Argonne National Laboratory has developed a catalytic reactor based on partial oxidation reforming that is suitable for use in light-duty vehicles powered by fuel cells. The reactor has shown the ability to convert a wide variety of fuels to a hydrogen-rich gas at less than 800 C, temperatures that are several hundreds of degrees lower than alternative noncatalytic processes. The fuel may be methanol, ethanol, natural gas, or petroleum-derived fuels that are blends of various hydrocarbons such as paraffins, olefins, aromatics, etc., as in gasoline. This paper will discuss the results obtained …

Excitations of nuclei close to magic {sup 132}Sn have been investigated by analysis of fission product {gamma}-ray data measured at Eurogam II using a {sup 248}Cm source. Results for the N=82 isotopes up to {sup 136}Xe, for the one proton-one neutron nucleus {sup 134}Sb, and for the N=84 isotones {sup 134}Sn. {sup 135}Sb, and {sup 136}Te are summarized. The interpretation of the observed level spectra is mainly based on shell model calculations using empirical proton-proton interactions from {sup 134}Te, neutron-neutron interactions from is {sup 134}Sn, and proton-neutron interactions estimated (with scaling as A{sup {minus}1/3}) from the well-known {sup 210}Bi spectrum.