It seems desirable to have some simple method for calculating quickly and with sufficient accuracy: 1) the correct position of the center of gravity; 2) the requisite tail-group dimensions; 3) and the course of the wing and tail-group moments. In out deductions, we will first replace the biplane (disregarding the effect of stagger, decalage and induced drag) by an equivalent monoplane, whose dimensions and position in space can be approximately determined in a simple manner.

The task of removing the boundary layer by suction consists in producing, in place of the ordinary flow with the formation of vortices, another kind of flow in which the vortices are eliminated by drawing small quantities of fluid from certain points on the surface into the interior of the body. The experiments with a sphere, which constitute the subject of this report, were made early in the present year .

In order that the method may be more easily understood, we will first consider the simpler case when there is no lift, but only drag, and when the streamlines at the measuring point behind the obstacle are nearly parallel. Moreover, the flow is assumed not to deviate much from the two-dimensional flow.

Memorandum describing warning or correcting devices based on the registering of two distinct factors, the air speed and the angle of attack. The authors of the report define the conditions for the flight of an airplane and then study the causes of stalled flight in the different cases where it can occur.

The staff and construction of the Institute are described as well as a variety of experiments and researches being conducted there. The six sections of the laboratory are described, including the Section for Theoretical Researches, Section for Aerodynamic Researches, Windmill Section, Section for Engine-Propeller Groups, Section for Material Testing, and Section for Instrument Making. Special attention is given to the various wind tunnels and testing facilities present.

Contents include the following: Characteristic differential equations - initial and boundary conditions. Integration of the second characteristic differential equations. Direct application of Meyer's characteristic hodograph table for construction of two-dimensional potential flows. Prandtl-Busemann method. Development of the pressure variation for small deflection angles. Numerical table: relation between deflection, pressure, velocity, mach number and mach angle for isentropic changes of state according to Prandtl-Meyer for air (k = 1.405). References.

"The wall interference is obtained for a wind tunnel of elliptic section for the two cases of closed and open working sections. The approximate and exact methods used gave results in practically good agreement. Corresponding to the result given by Glauert for the case of the closed rectangular section, the interference is found to be a minimum for a ratio of minor to major axis of 1:square root of 2" (p. 1).

This paper includes the following topics: 1) Characteristic differential equations; 2) Treatment of practical examples; 3) First example: Diffuser; and 4) Second Example: Nozzle.

"In a study of journal bearings, the measurement of the oil-film strength produces some significant information. A new instrument is described by means of which the pressure of the oil film in bearings (under constant or alternating load) can be measured and recorded. With this device, the pressure distribution in the lubricating film of a bearing bushing was measured (under different operating conditions on a journal bearing) in the pulsator-bearing-testing machine" (p. 1).

"The case of the horizontal cylinder is of particular importance in the study of heat transfer by free convection for the following reasons: In the first place, next to the rectangular plate it represents the simplest two-dimensional case; and second, a very wide range of measurements is possible, from the finest electrically heated glow lamp wires to pipes heated by liquids or gases flowing through them" (p. 1).

"The method described in the present report makes it possible to obtain interferometer records with the aid of any one of the available Schlieren optics by the addition of very simple expedients, which fundamentally need not to be inferior to those obtained by other methods, such as the Mach-Zehnder interferometer, for example. The method is based on the fundamental concept of the phase-contrast process developed by Zernike, but which in principle has been enlarged to such an extent that it practically represents an independent interference method for general applications. Moreover, the method offers the possibility, in case of necessity, of superposing any apparent wedge field on the density field to be gauged" (p. 1).

The investigations carried out in a previous report (NACA TM 1325) concerning the flow about ring-shaped cowlings were extended by taking a circulation about the cowling into consideration. The present second report treats bodies of infinite length with approximately smooth entrance. The circulation was caused by distributing vortex rings of constant density over a stream surface extending to infinity. Furthermore, the influence of a hub body on such cowlings was dealt with.

The equations of motion for an airplane penetrating a gust are derived using a few simplifying assumptions. Calculations of loads for different static longitudinal stability on two German airplane models, HC 45 and HS 122, are compared with flight tests. Good agreement is obtained between the trend of the flight tests and the calculated values; however no absolute comparison was possible between the flight tests and calculations.

A comprehensive survey of the elastic modulus of binary alloys as a function of the concentration is presented. Alloys that form continuous solid solutions, limited solid solutions, eutectic alloys, and alloys with intermetallic phases are investigated. Systems having the most important structures have been examined to obtain criteria for the relation between lattice structure, type of binding, and elastic behavior.

Drag tests at zero lift have been made at Mach numbers from 0.7 to approximately 0.95 in the high speed wind tunnel of the Institute of Aerodynamics, ETH, Zurich, on a group of untapered wings of aspect ratio 3.25, having sweep angles of 0 degree and 35 degrees. For each sweep angle, a series of geometrically similar models was tested at a constant Reynolds number to provide a verification of computed tunnel blocking corrections. Tests were also made for wings having thickness ratios of 0.09 and 0.12 and the results compared with results predicted by von Karman's similarity law.

The present paper gives the results of measurements of the resistance of a plate placed parallel to the flow in the range of Reynolds numbers from 10 to 2300; in this range the resistance deviates from the formula of Blasius. The lower limit of validity of the Blasius formula is determined and also the increase in resistance at the edges parallel to the flow in the case of a plate of finite width.

For determination of the elastic constants of airplane tires which are required for the numerical calculations of the shimmy properties of nose and tail wheels, deformation measurements were carried out on four different tires. For this purpose, the tires were loaded in each case with a normal load and then with a lateral force, a tangential force, and a moment. Moreover, the weight and the mass moment of inertia about a vertical axis were determined for the various tires.

This paper, which is presented in three parts, is an analytical study of the behavior of landing gear shock struts, with various types of assumptions for the shock-strut characteristics. The effects of tire springing are neglected. The first part compares the behavior of struts with linear and quadratic damping. The second part considers struts with nonlinear spring characteristics and linear or quadratic damping. The third part treats the oleo-pneumatic strut with air-compression springing without damping and with damping proportional to velocity.

"According to experience, a certain supersaturation is required for condensation of water vapor in the homogeneous phase; that is, for inception of the condensation, at a prescribed temperature, the water vapor partial pressure must lie above the saturation pressure. The condensation starts on so-called condensation nuclei. Solid or liquid suspended particles may serve as nuclei; these particles may either a priori be present in the gas phase (dust, soot), or may spontaneously be formed from the vapor molecules to be condensed themselves" (p. 1).

Part I of this paper covers the constructional design of metal flying-boat hulls and does not elaborate any further. Part II deals with the actual construction process of the hull.

This report examines the take-off conditions of airplanes equipped with tractive propellers, and particularly the more difficult take-off of airplanes heavily loaded per unit of wing area (wing loading) or per unit of engine power (power loading).

As a rule, the actual lift distribution at the wing tips shows deviations from the theoretical distribution, so that an approximate evaluation of the distribution may be regarded as satisfactory. After a few brief remarks on the fundamentals of the exact computation, the method will be so presented that the lift distribution for deflected ailerons may be determined for other values of the parameter p from the results already obtained. Coefficients will then be given in the form of diagrams and numerical tables, from which the desired forces and moments can be easily obtained by substitution in the given equations.

This report presents methods to reduce the incidence of aviation accidents. Some of the methods discussed include enlistment and training of aviators, improvement of controls and control surfaces, and upgrading of power plants.

The present report contains the results of a few experiments on three airfoils to which the rear portions, having chords respectively 1/4, 1/3, and 2/5 of the total chords, are hinged so as to form ailerons, especial attention being given to the shape of the slot between the aileron and the main portion of the aileron.