Rapid advances in computer software offer may opportunities for increasing efficiency and productivity; however, choosing the right software package and achieving its full potential can be a challenging task. Lubrication engineers faced with the selection and implementation of a computer system will find that they can increase their chance of success when they follow the nine steps outlined in this paper. These steps provide a solid framework for managing the project through its full life-cycle from initial conception until final retirement of the system. Lubrication Departments that already have computer systems in place can also benefit from these steps by picking up at the corresponding point in the system's life and following the remaining steps.

The major accomplishments of our initial research period (August 1, 1987, to March 1, 1990) are as follows; we completed construction of the experimental facility. Originally, it had been our intent to modify an existing facility in our laboratory. When this became impractical we constructed a new stand-alone facility. Modified an existing three-dimensional numerical code developed in our laboratory, SEAFLOS1, by incorporating a salinity transport equation. Developed experimental and analytical techniques, and performed both physical and numerical experiments for a wide range of initial and boundary conditions. Focused our overall research effort to answer the following four questions pertaining to the formation of convective intrusions due to lateral temperature gradients established by sidewall heating. (1) What is the internal structure of the convective intrusions as a function of the initial stratification and sidewall heating rates (2) What is the correct scaling for the initial vertical dimension of the intrusions (3) How does the merging process vary as a function of initial stratification and sidewall heating rate (4) Is the sidewall heating critical for continued propagation of the intrusions, or is it merely a trigger which releases the internal instability in the fluid

The Mirrortron accelerator is a plasma-based ion accelerator concept that, when implemented, should permit both higher acceleration gradients and higher peak-current capabilities than is possible with conventional induction-type accelerators. Control over the acceleration and focussing of an accelerated beam should approach that achieved in vacuum-field-based ion accelerators. In the Mirrortron a low density (10{sup 10} to 10{sup 11} cm{sup {minus}3}) hot electron'' plasma is confined by a long solenoidal magnetic field capped by mirrors''. Acceleration of prebunched ions is accomplished by activating a series of fast-pulsed mirror coils spaced along the acceleration tube. The hot electrons, being repelled by mirror action, leave the plasma ions behind to create a localized region of high electrical gradient (up to of order 100 MV/m). At the Laboratory an experiment and analyses to elucidate the concept and its scaling laws as applied to heavy-ion drivers are underway and will be described. 4 refs., 5 figs.

Studies of large-size (R = 1.5 m, a = 0.5 m), moderate current (I < 750 kA) reversed-field pinch (RFP) plasmas are carried out in the Madison Symmetric Torus in order to evaluate and improve RFP confinement, study general toroidal plasma MHD issues, determine the mechanism of the RFP dynamo, and measure fluctuation-induced transport and anomalous ion heating. MST confinement has been improved by reduction of magnetic field errors with correction coils in the primary circuit and reduction of impurities using boronization; high densities have been achieved with hydrogen pellet injection. MHD tearing modes with poloidal mode number m = 1 and toroidal mode numbers n = 5--7 are prevalent and nonlinearly couple to produce sudden relaxations akin to tokamak sawteeth. Edge fluctuation-induced transport has been measured with a variety of insertable probes. Ions exhibit anomalous heating, with increases of ion temperature occuring during strong MHD relaxation. The RFP dynamo has been studied with attention to various possible mechanisms, including motion-EMF drive, the Hall effect, and superthermal electrons. Initial profile control experiments have begun using insertable biased probes and plasma guns. The toroidal field capacity of MST will be upgraded during Summer, 1993 to allow low-current tokamak operation as well …

Nondestructive measurements of x-ray and gamma-ray emissions can be used to analyze a sample for plutonium. This report describes the methods and algorithms we have developed for analyzing gamma-ray spectra obtained by using a germanium detector system to accurately determine the relative abundances of various actinide isotopes in a sample. Our methodology requires no calibrations and can be used to measure virtually any size and type of plutonium sample. Measurement times can be as short as a few minutes; measurements are frequently accurate to within 1%. Our methods have been programmed into a computerized analysis code called MGA (Multi-Group Analysis). Our current versions can be run on personal computers (IBM type) and on the DEC VAX microcomputer. Spectral analysis times are usually far less than a minute. 28 refs., 26 figs., 1 tab.

The objective for this problem is to calculate the ground-level release dispersion factors (X/Q) and unit doses for onsite facility and offsite receptors at the site boundary and at Highway 240 for plume meander, building wake effect, plume rise, and the combined effect. The release location is at Central Waste Complex Building P4 in the 200 West Area. The onsite facility is located at Building P7. Acute ground level release 99.5 percentile dispersion factors (X/Q) were generated using the GXQ. The unit doses were calculated using the GENII code. The dimensions of Building P4 are 15 m in W x 24 m in L x 6 m in H.

This engineering note documents the testing of the set pressure of the EC hydraulic drive cylinder relief valve. The purpose of the relief valve is to provide a safety measure in the event that oil becomes trapped in the rod side of the cylinder and pressure is applied to the cap side. The note includes an explanation of the procedure used and a summary of the result of the testing done on February 14, 1991 by Gary Trotter. The result was that the cylinder relief valve relieved at the correct set pressure of 10,500 psig. The basic concern is for the protection of the cylinder. The pump is capable of providing up to 10,500 psi of pressure to either side of the cylinder. The cylinder is rated for 10,500 psi. Under normal operating conditions, the valves would be open, and the pumping pressure would automatically flow oil into one side, and remove oil from the other side. If, however, the valve for the other side was closed, so that oil could not be removed, then the pressure would build in that side. If the rod side is pressurized to the maximum pump pressure of 10,500 psi, the cross sectional area …

A thin, elastic elliptical ring is subjected to uniform external pressure. The lowest critical pressure is computed and presented for various ratio of the major axis to the minor axis of the elliptical ring. It is found that the critical pressure for an elliptical ring is higher than that for the circular ring whose diameter is equal to the major axis of the elliptical ring. It can be shown that under the same external pressure, the axial force developed in the elliptical ring is less than that developed in the corresponding circular ring. Thus, a higher pressure is required to buckle the elliptical rings. Therefore, by changing the shape of the ring from circular to elliptical, the capability of the ring to sustain the external pressure can be increased substantially. The results of this study can be useful in the design of elliptical reinforcing rings and thin-walled tubes subjected to external pressure.

As the systems engineering activities at the US Department of Energy`s Hanford reservation have matured, they have been placed in many positions within the management structure. Some of these have been more successful than others. This paper describes the organizational evolution of systems engineering over the last few years to its current successful configuration. Background The US Department of Energy (DOE) owns the 640 square mile Hanford reservation located in southeast Washington State (Figure 1). The Site has been operated for DOE by a team of contractors, who read like a Who`s Who in American Industry. Throughout its history from its founding in 1943 until 1991, Hanford`s primary mission was to produce special nuclear material for the nuclear weapons program. This mission resulted in significant quantities of radioactive and mixed waste that is stored on the site in a variety of forms. In addition much of the surface area, subsurface soil, and groundwater are contaminated to various degrees. The Reservation is located on the banks of the Columbia River, and the avoidance of contaminating the waterway that services the Pacific Northwest is a national concern. In 1991, the mission of the Hanford Site was changed from production to environmental cleanup. …

Studies of large-size (R = 1.5 m, a = 0.5 m), moderate current (I < 750 kA) reversed-field pinch (RFP) plasmas are carried out in the Madison Symmetric Torus in order to evaluate and improve RFP confinement, study general toroidal plasma MHD issues, determine the mechanism of the RFP dynamo, and measure fluctuation-induced transport and anomalous ion heating. MST confinement has been improved by reduction of magnetic field errors with correction coils in the primary circuit and reduction of impurities using boronization; high densities have been achieved with hydrogen pellet injection. MHD tearing modes with poloidal mode number m = 1 and toroidal mode numbers n = 5--7 are prevalent and nonlinearly couple to produce sudden relaxations akin to tokamak sawteeth. Edge fluctuation-induced transport has been measured with a variety of insertable probes. Ions exhibit anomalous heating, with increases of ion temperature occuring during strong MHD relaxation. The RFP dynamo has been studied with attention to various possible mechanisms, including motion-EMF drive, the Hall effect, and superthermal electrons. Initial profile control experiments have begun using insertable biased probes and plasma guns. The toroidal field capacity of MST will be upgraded during Summer, 1993 to allow low-current tokamak operation as well …

Emissions of hazardous air pollutants from coal combustion were studied in a laboratory-scale combustion facility, with emphasis on fine particles in three size ranges of less than 7.5 {mu}m diameter. Vapors were also measured. Substances under study included organic compounds, anions, elements, and radionuclides. Fly ash was generated by firing a bituminous coal in a combuster for 40 h at each of two coal feed rates. Flue gas was sampled under two conditions. Results for organic compounds, anions, and elements show a dependence on particle size consistent with published power plant data. Accumulation of material onto surface layers was inferred from differences in chemical composition between the plume simulating dilution sampler and hot flue samples. Extracts of organic particulate material were fractionated into different polarity fractions and analyzed by GC/MS. In Phase II, these laboratory results will be compared to emissions from a full-scale power plant burning the same coal.

Large volumes of hydrocarbons are stored worldwide in surface and underground tanks. It is well documented [1] that all too often these tanks are found to leak, resulting in not only a loss of stored inventory but, more importantly, contamination to soil and groundwater. Two field experiments are reported herein to evaluate the utility of electrical resistance tomography (ERT) for detecting and locating leaks as well as delineating any resulting plumes emanating from steel underground storage tanks (UST). Current leak detection methods for single shell tanks require careful inventory monitoring, usually from liquid level sensors within the tank, or placement of chemical sensors in the soil under and around the tank. Liquid level sensors can signal a leak but are limited in sensitivity and, of course, give no information about the location or the leak or the distribution of the resulting plume. External sensors are expensive to retrofit and must be very densely spaced to assure reliable detection, especially in heterogeneous soils. The rational for using subsurface tomography is that it may have none of these shortcomings.

The CO conversion and isobutylene yield for Runs 11 to 20 (except run 12) at the conditions of 450[degree]C, 1,200 psig, and 1,920 gas hourly space velocity (GHSV), Is given in Table 2. These conditions generally provide the maximum CO conversion for each run. Runs 5 to 10 is also provided in Table 2 for a comparison. The description of the catalysts also given in Table 2 includes the composition, method of preparation, and calcination temperature for each catalyst tested. Data for Runs 12 and 21 are at different conditions, as discussed later in this report. The conversion and yield data were obtained at relatively short times on-stream ([approximately]11 hours). The extent of catalyst deactivation has not been determined. The freshly precipitated CeO[sub 2] catalyst, IS-9, is by far the most active but is poorly selective to Isobutene. The catalyst primarily produces saturated by-products. The commercial CeO[sub 2,] IS-8, had low surface area and little activity. Earlier tests show that lowering the calcination temperature of precipitated catalysts produced higher surface areas, higher tetragonal content, higher activity and higher yields. The ZrO[sub 2] sol-gel catalysts show a similar relationship. A comparison of Run 9 (ZrO[sub 2] calcined at 600[degree]C) and Run …

The CO conversion and isobutylene yield for Runs 11 to 20 (except run 12) at the conditions of 450{degree}C, 1,200 psig, and 1,920 gas hourly space velocity (GHSV), Is given in Table 2. These conditions generally provide the maximum CO conversion for each run. Runs 5 to 10 is also provided in Table 2 for a comparison. The description of the catalysts also given in Table 2 includes the composition, method of preparation, and calcination temperature for each catalyst tested. Data for Runs 12 and 21 are at different conditions, as discussed later in this report. The conversion and yield data were obtained at relatively short times on-stream ({approximately}11 hours). The extent of catalyst deactivation has not been determined. The freshly precipitated CeO{sub 2} catalyst, IS-9, is by far the most active but is poorly selective to Isobutene. The catalyst primarily produces saturated by-products. The commercial CeO{sub 2,} IS-8, had low surface area and little activity. Earlier tests show that lowering the calcination temperature of precipitated catalysts produced higher surface areas, higher tetragonal content, higher activity and higher yields. The ZrO{sub 2} sol-gel catalysts show a similar relationship. A comparison of Run 9 (ZrO{sub 2} calcined at 600{degree}C) and Run …

The ''Cold War'' was not fought only by soldiers but by scientists and engineers in Laboratories and plants located throughout the world. With the fall of the Berlin Wall, the ''Cold War'' was effectively over, but the weapons of nuclear war remained. Following signing of START 2 (Strategic Arms Reduction Treaty) in 1993, up to 100 tonnes of weapons usable plutonium is expected to be declared excess by the Super Powers. Steps must be taken to address the proliferation risks associated with this plutonium. Again the scientist and engineers, who were the ''Cold War'' warriors, are being asked to develop methods to disposition this plutonium such that it can never again be used for weapons. Will we burn the plutonium in reactors or immobilize the plutonium either in a glass or ceramic matrix? Interesting challenges face chemists and chemical engineers developing immobilization techniques to render the plutonium both environmentally benign, and proliferation resistant.

This Acceptance Test Report (ATR) documents for record purposes the field results, acceptance, and approvals of the completed acceptance test per HNF-SD-W417-ATP-001, ''Rail car Waste Transfer System Hydrostatic Test''. The test was completed and approved without any problems or exceptions.

The following topics are discussed: A new thermodynamical theory of continuum damage mechanics capable of incorporating non-isothermal processes and of providing explicit expressions for the thermal dissipation during damage evolution; the advancement of the methodology of heterogenization to analyze elastic bodies with defects; and investigations of bonded dissimilar piezoelectric half-spaces.

This report was prepared by Westinghouse Hanford Company (WHC) with technical and cost estimating support from Pacific Northwest Laboratories (PNL) and Parsons Environmental Services, Inc. (Parsons). This engineering study evaluates the requirements and alternatives for decontamination/treatment of contaminated equipment at the Hanford Site. The purpose of this study is to determine the decontamination/treatment strategy that best supports the Hanford Site environmental restoration mission. It describes the potential waste streams requiring treatment or decontamination, develops the alternatives under consideration establishes the criteria for comparison, evaluates the alternatives, and draws conclusions (i.e., the optimum strategy for decontamination). Although two primary alternatives are discussed, this study does identify other alternatives that may warrant additional study. hanford Site solid waste management program activities include storage, special processing, decontamination/treatment, and disposal facilities. This study focuses on the decontamination/treatment processes (e.g., waste decontamination, size reduction, immobilization, and packaging) that support the environmental restoration mission at the Hanford Site.

Field emission cathodes (FECs) with characteristics of cold emission, low voltage operation, high current density and microscopic size meet the requirements for an electron source for use in vacuum microelectronics. Deposition efforts have focused on evaporation techniques, as electron beam, to produce the size and shape of cathode required for efficient operation. After two decades of development, the convention for FEC synthesis involves coating with very high tolerances for thickness uniformity using a planetary substrate fixture and a long source-to-substrate distance. A further reduction in the operating voltage results by increasing the density of emitters through a reduction of cathode size and spacing. In addition, the objective of scaling the substrate size from small to large areas has compounded the manufacturing requirements to a point beyond that which is obtainable through modifications to the conventional FEC deposition process. We have been successful in a new alternative approach to design, assemble and operate a system that enables FEC synthesis over large areas through the control of deposition source divergence and step-and-repeat substrate handling.

Infrared computed tomography (IRCT) is a promising, non-contact, nondestructive evaluation tool used to inspect the mechanical integrity of large structures. We describe on-site, proof-of-principle demonstrations of IRCt to inspect defective metallic and composite structures. The IRCT system captures time sequences of heat-stimulated, dual-band infrared (DBIR) thermal maps for flash-heated and naturally-heated targets. Our VIEW algorithms produce co-registered thermal, thermal inertia, and thermal-timegram maps from which we quantify the percent metal-loss corrosion damage for airframes and the defect sites, depths, and host-material physical properties for composite structures. The IRCT method clarifies the type of defect, e.g., corrosion, fabrication, foreign-material insert, delamination, unbond, void, and quantifies the amount of damage from the defect, e.g., the percent metal-loss from corrosion in metal structures, the depth, thickness, and areal extent of heat damage in multi-layered composite materials. Potential long-term benefits of IRCT technology are in-service monitoring of incipient corrosion damage, to avoid catastrophic failure and production-monitoring of cure states for composite materials.

The objective of this project was to determine the suitability of oxidation in supercritical fluids (SCO), particularly water (SCWO), for disposal of propellants, explosives, and pyrotechnics (PEPs). The SCO studies of PEPs addressed the following issues: The efficiency of destruction of the substrate. The products of destruction contained in the effluents. Whether the process can be conducted safely on a large scale. Whether energy recovery from the process is economically practicable. The information essential for process development and equipment design was also investigated, including issues such as practical throughput of explosives through a SCWO reactor, reactor materials and corrosion, and models for process design and optimization.

This paper makes a case for the use of participatory ergonomics by and for ergonomists. A strategy for using participatory ergonomics in a conference workshop format is described. The process could be used as a tool for issues of common concern among ergonomists. it would also offer an experience of the participatory ergonomics process. An example workshop on quantifying costs and benefits of ergonomics is discussed.

Continuous, high quality profiles of water vapor, free of systematic bias, and of moderate temporal and spatial resolution, acquired over long periods at low operational and maintenance cost, are fundamental to the success of the ARM CART program. The development and verification of realistic climate model parameterizations for clouds and net radiation balance, and the correction of other CART site sensor observations for interferences due to the presence of water vapor are critically dependent on water vapor profile measurements. Application of profiles acquired with current techniques, have, to date, been limited by vertical resolution and uniqueness of solution [e.g. high resolution infrared (IR) Fourier transform radiometry], poor spatial and temporal coverage and high operating cost (e.g. radiosondes), or diminished daytime performance, lack of eye-safety, and high maintenance cost (e.g. Raman lidar). Recent developments in infrared laser and detector technology make possible compact IR differential absorption lidar (DIAL) systems at eye-safe wavelengths. In the study reported here, we develop DIAL system performance models and examine the potential of to solve some of the shortcomings of previous methods using parameterizations representative of current technologies. These models are also applied to diagnose and evaluate other strengths and weaknesses unique to the DIAL method …

The objective of this project was to create a system that delivered the appropriate information to the machine tool user just when needed and in the most appropriate form. The expertise of FM&amp;T in the areas of instructional system design and multimedia creation was employed. Huffman brought together their subject matter experts from engineering, manufacturing, technical writing, and technical support. AlliedSignal FM&amp;T worked together with Huffman as a design team to determine what tasks must be accomplished throughout the machine tool production phases, who performs those tasks, what skills are utilized, and what information is required to support the tasks. This project resulted in the identification of information flow throughout the life cycle of the machine tool products. Specialized tools required for assembly and calibration procedures were identified and their images captured, digitized, and stored for easy retrieval within the PSS. Subject matter experts were interviewed to determine which tasks require highly specialized knowledge and skills. These tasks were then performed on actual machines and the technicians' actions captured on video tape. The resulting video segments were edited, digitized, and integrated into the information system portion of the PSS where they are available for viewing alongside procedural information presented on …