Introduction: The objective of Project Agreement 22 is to determine the feasibility of covering the complete reactor neutron flux start range from 10(3) - 5 x 10(13) nv by using in-core chambers. The counting mode of operating will be used at low neutron fluxes and the root mean square voltage fluctuation mode will be used at high neutron flux levels. Experiments have been run utilizing various ion chambers, gases, gas pressures, voltage, and cables to measure sensitivities and range operating in the counting and RMS voltage modes. Theoretical discussions are presented showing how the RMS voltage is related to individual pulse at both amplifier input and output. Noise is also compared at amplifier output so that the optimum bandwidth can be selected. Spectral shifts with changes in applied voltage causing signal variations have been examined and can be eliminated by appropriate selection of amplifier bandwidth. In the counting mode, all experiments have been conducted with unterminated cable. The chamber has been designed with geometry, gas, and pressure to completely stop fission fragments in the gas and hence maximize the charge generated in the chamber. Cables have been selected to minimize capacity. Various gases, pressures, and voltages have been used to …

This is the sixteenth quarterly report of the research and development activities of the Radiological Sciences Department, Hanford Atomic Products Operation, as before, includes some items charged to control but included for general interest. Such are identified as "not charged to research."

Abstract: An analysis of SM-1 Core II and SM-1A Core I zero power experiments was made by comparing these cores to each other and to AM-1 Core I on the basis of critical bank positions, bank calibrations and available chemical analyses of the fuel plate compositions. The effects of replacing boron absorbers by europium absorbers upon rod worth and stuck rod conditions were studied. Comparisons of measured and calculated power distributions were made. It was concluded that both SM-1 Core II and SM-1A Core I contain nearly identical B-10 loading of 17.79 grams, compared to the best estimate of 15.75 grams for SM-1 Core I. The available data indicates that all three cores possess similar nuclear characteristics.

Abstract: The removal of both SM-1 Core I high burnup elements from SM-1 Core II and the insertion of the PM-1-M-2 element and the SM-1 Core I spare element in SM-1 Core II is discussed. Nuclear and thermal characteristics of Core II with these changes are presented and conclusions related to the changes in the hazard potential are made. If the core change indicated by this report is made, local peaking factors will be decreased and burnout ratios will be increased. This, of course, in itself leads to a more conservative estimate of core safety. There is no conceivable reason why the perturbation may not be safely made in the SM-1 Core II.

Abstract: This technical report elucidates principles of hazards evaluation. The concept of hazards potential is introduced and utilized to show how a reactor system perturbation will influence its nuclear safety. Literature relating to reactor safety is referenced to provide the sources of information required for hazards analysis and show how they influence a hazards evaluation. A checklist of items which should be considered in evaluating a change, test, or modification is presented.

Activities in a program to develop techniques in the use of pulsed neutron sources to measure shutdown parameters related to large thermal power reactors are reported. The development of pulsed neutron source techniques for large power reactors has led to a new theoretical model recently developed by E. Garelis and J.L. Russell, Jr. The theory is presently based on a bare, one-group model with m-delayed precursors and takes all spatial modes into account. Results indicate, however, that the application of this model is much broader. Experiments were designed and carried out to both verify this new theory and to demonstrate the performance of the experimental hardware in a large power reactor.

Development of nuclear reactor cores having high power density, long fuel life, and low fabrication costs is the objective of this program sponsored by the AEC. Five tasks are in progress: (1) Task 1A-High Power Density Fuel Development. The number of assemblies has been reduced to seven as a result of the failure of two pellet fuel assemblies. The average burnup of the group operating as of September 1 is 7500 MWD/T. (2) Task 1B-Fuel Fabrication Development. Assembly. Assembly 12S gave positive signals of being a leaker under the multi-type in-core sampler and was declared failed based on the in-core results and visual observation of a cracked rod. Modifications to the instrumented fuel assembly probes were made by removing the failed flow meter rotors to allow continued use of the flux detectors and thermocouples. Flux detectors and thermocouples performed properly after reactor start up. Flux wire tubes were found to be kinked such that their use was prohibited. (3) Task II-Stability, Heat Transfer and Fluid Flow. A series of noise recordings of fluxes, flows, and temperatures has been made at 91 MWt at the Big Rock Point plant. Preliminary analyses of some of the these records were made to obtain …

Technical report describing sixteen fuel rods clad with thin type 304 stainless steel and filled with vibratory compact powder UO2 that were fabricated and incorporated into a bundle for irradiation testing in the VBWR. The UO2 powders were tested for gas content. N2, CO, and H2 were the principal gases evolved by both type of UO2, but the arc-fused UO2 released about ten times as much gas as the Dyna Pak UO2. The amount of gas released was also a function of particle size and temperature. The gas evolution data were used to design the gas plenum to accommodate the absorbed gases along with the fission gases.

Technical report of a proposal of an analytical model to predict two-phase critical flow rate. The model is based upon thermal equilibrium, a "lumped" treatment of the two-phase velocity (each phase is represented by a single mean velocity), and upon the neglect of frictional and hydrostatic pressure losses. A comparison, of the proposed predictions with available test results and previous analyses shows that: (1) The present model agrees very well with the published test data. (2) In contrast to all other analyses, the model requires no assumption about the gas void fraction.

Summary: A prototype control rod containing absorber plates made from an electro- deposited dispersion of boron carbide in nickel was tested in the VBWR. It was exposed to the reactor environment of 545 degree F boiling water and thermal neutron fluxes (perturbed) which ranged from 0.6 to 1.1 x 10/sup 13/ nv for 2236 hours over a period of six months. The maximum B/sup 10/ burnup achieved during the test period was 1.8 percent. After irradiation, the rod was examined. The results of the examination are summarized below: (1) The B/sub 4/C-- Ni plate assembly did not undergo significant dimensional changes during irradiation. (2) Numerous blisters developed on both the outer and inner surfaces of three of the four plates. Blistering was more severe on the outer surface than on the inner, and was most severe in a large region located in the lower half of plate 4. Metallographic examination revealed that the blisters were located only in the 2- mil protective nickel overlay covering the B/sub 4/C-- Ni dispersion. It was concluded that they formed from the buildup of gas pressure at the Ni: Ni-- B/sub 4/C interfaces, rather than from corrosion attack. Helium from the B/sup 10/(n alpha …

Abstract: The removal of both SM-1 Core I high burnup elements from the SM-1 Core II and the insertion of two SM-1 Core I spare elements i their places are discussed. Nuclear and thermal characteristics of Core II with the change are presented and conclusion related to the change in hazard potential are made. If the core change indicated by this report is made, local peaking factors will be decreased and burnout ratios will be increased. This, of course, in itself leads to a more conservative estimate of core safety. There is no conceivable reason why this perturbation may not be safely made in the SM-1 Core II.

Abstract: A zero power experiment on the SM-1 Core II included an element by element reactivity check of fuel elements and control rod absorber sections, and an estimate of burnable nuclear poison loading in stationary fuel elements. An approach to criticality was made by the inverse multiplication method, and critical rod bank position obtained as a function fuel loading up to full core loading. Minimum and maximum core reactivity measurements were obtained by selective loading of stationary fuel elements, and total excess K of the core was established. Power distribution measurements were taken in the regions of the core-reflector interface and the fuel-absorber interface in the control rod assemblies. The effectiveness of europium flux suppressors in the top of control rod fuel elements was determined, and power peaking was measured in stationary elements adjacent to control rod assembly water gaps. Survey measurements established the work of spiking clean, cold SM-1 cores with SM-2 elements and the work of water holes in the SM-1 Core. The reduced scope zero power experiment performed on SM-1A core I included an element by element uniformity check of stationary fuel elements, a core assembly test, comparison of Eu2O3 and B4C absorber sections, and development of …