Introduction: The objective of Project Agreement 22 is to determine the feasibility of covering the complete reactor neutron flux start range from 10(3) - 5 x 10(13) nv by using in-core chambers. The counting mode of operating will be used at low neutron fluxes and the root mean square voltage fluctuation mode will be used at high neutron flux levels. Experiments have been run utilizing various ion chambers, gases, gas pressures, voltage, and cables to measure sensitivities and range operating in the counting and RMS voltage modes. Theoretical discussions are presented showing how the RMS voltage is related to individual pulse at both amplifier input and output. Noise is also compared at amplifier output so that the optimum bandwidth can be selected. Spectral shifts with changes in applied voltage causing signal variations have been examined and can be eliminated by appropriate selection of amplifier bandwidth. In the counting mode, all experiments have been conducted with unterminated cable. The chamber has been designed with geometry, gas, and pressure to completely stop fission fragments in the gas and hence maximize the charge generated in the chamber. Cables have been selected to minimize capacity. Various gases, pressures, and voltages have been used to …

Activities in a program to develop techniques in the use of pulsed neutron sources to measure shutdown parameters related to large thermal power reactors are reported. The development of pulsed neutron source techniques for large power reactors has led to a new theoretical model recently developed by E. Garelis and J.L. Russell, Jr. The theory is presently based on a bare, one-group model with m-delayed precursors and takes all spatial modes into account. Results indicate, however, that the application of this model is much broader. Experiments were designed and carried out to both verify this new theory and to demonstrate the performance of the experimental hardware in a large power reactor.

Development of nuclear reactor cores having high power density, long fuel life, and low fabrication costs is the objective of this program sponsored by the AEC. Five tasks are in progress: (1) Task 1A-High Power Density Fuel Development. The number of assemblies has been reduced to seven as a result of the failure of two pellet fuel assemblies. The average burnup of the group operating as of September 1 is 7500 MWD/T. (2) Task 1B-Fuel Fabrication Development. Assembly. Assembly 12S gave positive signals of being a leaker under the multi-type in-core sampler and was declared failed based on the in-core results and visual observation of a cracked rod. Modifications to the instrumented fuel assembly probes were made by removing the failed flow meter rotors to allow continued use of the flux detectors and thermocouples. Flux detectors and thermocouples performed properly after reactor start up. Flux wire tubes were found to be kinked such that their use was prohibited. (3) Task II-Stability, Heat Transfer and Fluid Flow. A series of noise recordings of fluxes, flows, and temperatures has been made at 91 MWt at the Big Rock Point plant. Preliminary analyses of some of the these records were made to obtain …

Technical report describing sixteen fuel rods clad with thin type 304 stainless steel and filled with vibratory compact powder UO2 that were fabricated and incorporated into a bundle for irradiation testing in the VBWR. The UO2 powders were tested for gas content. N2, CO, and H2 were the principal gases evolved by both type of UO2, but the arc-fused UO2 released about ten times as much gas as the Dyna Pak UO2. The amount of gas released was also a function of particle size and temperature. The gas evolution data were used to design the gas plenum to accommodate the absorbed gases along with the fission gases.

Technical report of a proposal of an analytical model to predict two-phase critical flow rate. The model is based upon thermal equilibrium, a "lumped" treatment of the two-phase velocity (each phase is represented by a single mean velocity), and upon the neglect of frictional and hydrostatic pressure losses. A comparison, of the proposed predictions with available test results and previous analyses shows that: (1) The present model agrees very well with the published test data. (2) In contrast to all other analyses, the model requires no assumption about the gas void fraction.

Summary: A prototype control rod containing absorber plates made from an electro- deposited dispersion of boron carbide in nickel was tested in the VBWR. It was exposed to the reactor environment of 545 degree F boiling water and thermal neutron fluxes (perturbed) which ranged from 0.6 to 1.1 x 10/sup 13/ nv for 2236 hours over a period of six months. The maximum B/sup 10/ burnup achieved during the test period was 1.8 percent. After irradiation, the rod was examined. The results of the examination are summarized below: (1) The B/sub 4/C-- Ni plate assembly did not undergo significant dimensional changes during irradiation. (2) Numerous blisters developed on both the outer and inner surfaces of three of the four plates. Blistering was more severe on the outer surface than on the inner, and was most severe in a large region located in the lower half of plate 4. Metallographic examination revealed that the blisters were located only in the 2- mil protective nickel overlay covering the B/sub 4/C-- Ni dispersion. It was concluded that they formed from the buildup of gas pressure at the Ni: Ni-- B/sub 4/C interfaces, rather than from corrosion attack. Helium from the B/sup 10/(n alpha …