This manual is a general resource tool to assist EMSL users and Laboratory staff within EMSL locate official policy, practice and subject matter experts. It is not intended to replace or amend any formal Battelle policy or practice. Users of this manual should rely only on Battelle’s Standard Based Management System (SBMS) for official policy. No contractual commitment or right of any kind is created by this manual. Battelle management reserves the right to alter, change, or delete any information contained within this manual without prior notice.

A 3-L sludge slurry sample from Tank 12 was characterized and then processed through an aluminum dissolution demonstration. The dominant constituent of the sludge was found to be aluminum in the form of boehmite. The iron content was minor, about one-tenth that of the aluminum. The salt content of the supernatant was relatively high, with a sodium concentration of {approx}7 M. Due to these characteristics, the yield stress and plastic viscosity of the unprocessed slurry were relatively high (19 Pa and 27 cP), and the settling rate of the sludge was relatively low ({approx}20% settling over a two and a half week period). Prior to performing aluminum dissolution, plutonium and gadolinium were added to the slurry to simulate receipt of plutonium waste from H-Canyon. Aluminum dissolution was performed over a 26 day period at a temperature of 65 C. Approximately 60% of the insoluble aluminum dissolved during the demonstration, with the rate of dissolution slowing significantly by the end of the demonstration period. In contrast, approximately 20% of the plutonium and less than 1% of the gadolinium partitioned to the liquid phase. However, about a third of the liquid phase plutonium became solubilized prior to the dissolution period, when the …

Topological insulators are new states of quantum matter with surface states protected by the time-reversal symmetry. In this work, we perform first-principle electronic structure calculations for Sb{sub 2}Te{sub 3}, Sb{sub 2}Se{sub 3}, Bi{sub 2}Te{sub 3} and Bi{sub 2}Se{sub 3} crystals. Our calculations predict that Sb{sub 2}Te{sub 3}, Bi{sub 2}T e{sub 3} and Bi{sub 2}Se{sub 3} are topological insulators, while Sb{sub 2}Se{sub 3} is not. In particular, Bi{sub 2}Se{sub 3} has a topologically non-trivial energy gap of 0.3eV , suitable for room temperature applications. We present a simple and unified continuum model which captures the salient topological features of this class of materials. These topological insulators have robust surface states consisting of a single Dirac cone at the {Lambda} point.

This summary of the research progress meeting for March 25, 1948 covers the following topics: (1) Recent n-p scattering measurements; (2) Mass measurements of mesons; and (3) Naphthalene counters.

The Society for Energy and Environmental Research (SEER) was funded in March 2004 by the Department of Energy, under grant DE-FG-36-04GO14268, to produce a study, and oversee construction and implementation, for the thermo-chemical production of fuel from agricultural and animal waste. The grant focuses on the Changing World Technologies (CWT) of West Hempstead, NY, thermal conversion process (TCP), which converts animal residues and industrial food processing biproducts into fuels, and as an additional product, fertilizers. A commercial plant was designed and built by CWT, partially using grant funds, in Carthage, Missouri, to process animal residues from a nearby turkey processing plant. The DOE sponsored program consisted of four tasks. These were: Task 1 Optimization of the CWT Plant in Carthage - This task focused on advancing and optimizing the process plant operated by CWT that converts organic waste to fuel and energy. Task 2 Characterize and Validate Fuels Produced by CWT - This task focused on testing of bio-derived hydrocarbon fuels from the Carthage plant in power generating equipment to determine the regulatory compliance of emissions and overall performance of the fuel. Task 3 Characterize Mixed Waste Streams - This task focused on studies performed at Princeton University to better …

After 1970 Transuranic (TRU) and suspect TRU waste was buried in the ground with the intention that at some later date the waste would be retrieved and processed into a configuration for long term storage. To retrieve this waste the soil must be removed (excavated). Sloping the bank of the excavation is the method used to keep the excavation from collapsing and to provide protection for workers retrieving the waste. The purpose of this paper is to document the minimum distance (setback) that equipment must stay from the edge of the excavation to maintain a stable slope. This evaluation examines the equipment setback distance by dividing the equipment into two categories, (1) equipment used for excavation and (2) equipment used for retrieval. The section on excavation equipment will also discuss techniques used for excavation including the process of benching. Calculations 122633-C-004, 'Slope Stability Analysis' (Attachment A), and 300013-C-001, 'Crane Stability Analysis' (Attachment B), have been prepared to support this evaluation. As shown in the calculations the soil has the following properties: Unit weight 110 pounds per cubic foot; and Friction Angle (natural angle of repose) 38{sup o} or 1.28 horizontal to 1 vertical. Setback distances are measured from the top …

Tests were performed to determine the effect cleanliness of a surface exposed to tritium gas had on methane formation. These tests performed on 304 stainless steel vessels, cleaned in various ways, showed that the methane formation was reduced by the use of various cleaning procedures.

The objectives of the confirmatory activities were to provide independent contractor field data reviews and to generate independent radiological data for use by the NRC in evaluating the adequacy and accuracy of the contractor�s procedures and FSS results. ORAU reviewed ABB CE�s decommissioning plan, final status survey plan, and the applicable soil DCGLs, which were developed based on an NRC-approved radiation dose assessment. The surveys include gamma surface scans, gamma direct measurements, and soil sampling.

A performance assessment is required to demonstrate compliance with the post-closure performance objectives for the Yucca Mountain Project (YMP), as stated in 10 CFR Part 63.1 13 (66 FR 55732, p. 55807). A performance assessment is defined in 10 CFR 63.2 (66 FR 55732, p. 55794) as an analysis that: (1) identifies the features, events, and processes (FEPs) that might affect the potential geologic repository; (2) examines the effects of those FEPs upon the performance of the potential geologic repository; and (3) estimates the expected dose incurred by a specified reasonably maximally exposed individual as a result of releases caused by significant FEPs. The performance assessment must also provide the technical basis for inclusion or exclusion of specific FEPs in the performance assessment as stated in 10 CFR 63.114 (66 FR 55732, p. 55807). An initial approach for FEP development, in support of the Total System Performance Assessment for the Site Recommendation (TSPA-SR) (CRWMS M&O 2000e), was documented in Freeze et al. (2001). The development of a comprehensive list of FEPs potentially relevant to the post-closure performance of the potential Yucca Mountain repository is an ongoing, iterative process based on site-specific information, design, and regulations. Although comprehensiveness of the FEPs …

Mineral carbonation provides a potential option for the long-term storage of carbon dioxide. Serpentine has been chosen as the feedstock mineral, due to its abundance and availability. However, the relatively low reactivity of serpentine has warranted research into physical and chemical treatments that have been shown to greatly increase its reactivity. The use of sulfuric acid as an accelerating medium for the removal of magnesium from serpentine has recently been investigated. In addition to the challenges presented by the dissolution of serpentine, another challenge is the subsequent carbonation of the magnesium ions. A stable hydration sphere for the magnesium ion reduces the carbonation kinetics by obstructing the formation of the carbonation products. Accordingly, this research has evaluated the solubility of carbon dioxide in aqueous solution, the interaction between the dissociation products of carbon dioxide, and the carbonation potential of the magnesium ion.

None

Progress made in the field of spectrophotometry of molten fluoride salts is summarized. The high-temperature cell assembly designed and fabricated for use in this work is described, as well as the various types of sample containers used. Spectra of nickel fluoride, cobalt fluoride, chromic fluoride, and uranium tetrafluoride in LiF--NaF-KF (46.5-11.5--42 mole%) are presented. (auth)

The WTP pipe plugging issue, as stated by the External Flowsheet Review Team (EFRT) Executive Summary, is as follows: “Piping that transports slurries will plug unless it is properly designed to minimize this risk. This design approach has not been followed consistently, which will lead to frequent shutdowns due to line plugging.” A strategy was employed to perform critical-velocity tests on several physical simulants. Critical velocity is defined as the point where a stationary bed of particles deposits on the bottom of a straight horizontal pipe during slurry transport operations. Results from the critical velocity testing provide an indication of slurry stability as a function of fluid rheological properties and transport conditions. The experimental results are compared to the WTP design guide on slurry transport velocity in an effort to confirm minimum waste velocity and flushing velocity requirements as established by calculations and critical line velocity correlations in the design guide. The major findings of this testing is discussed below. Experimental results indicate that the use of the Oroskar and Turian (1980) correlation in the design guide is conservative—Slurry viscosity has a greater affect on particles with a large surface area to mass ratio. The increased viscous forces on these …

BioConversion Technology, LLC has developed a novel gasifier design that produces a clean, medium to high BTU synthesis gas that can be utilized for a variety of applications. The staged, indirectly heated design produces high quality synthesis gas without the need for costly pure oxygen. This design also allows for extreme flexibility with respect to feedstocks (including those with high moisture contents) in addition to high throughputs in a small gasifier footprint. A pilot scale testing project was proposed to assist BCT with commercializing the process. A prototype gasifier constructed by BCT was transported to WRI for installation and testing. After troubleshooting, the gasifier was successfully operated with both coal and biomass feedstocks. Instrument upgrades are recommended for further testing.

A set of the electrostatic toroidal gyrokinetic Vlasov equation and the Poisson equation, which explicitly includes the polarization drift, is derived systematically by using Lie-transform method. The polarization drift is introduced in the gyrocenter equations of motion, and the corresponding polarization density is derived. Contrary to the wide-spread expectation, the inclusion of the polarization drift in the gyrocenter equations of motion does not affect the expression for the polarization density significantly. This is due to modification of the gyrocenter phase-space volume caused by the electrostatic potential [T. S. Hahm, Phys. Plasmas 3, 4658 (1996)] .

For both the United States and Canada, testing has been under way for electric utilities to find viable and economical mercury control strategies to meet pending future mercury emission limits. The technology that holds the most promise for mercury control in low-chlorine lignite to meet the needs of the Clean Air Act in the United States and the Canada-Wide Standards in Canada is injection of treated activated carbon (AC) into the flue gas stream. Most of the treated carbons are reported to be halogenated, often with bromine. Under a previous multiyear project headed by the Energy & Environmental Research Center (EERC), testing was performed on a slipstream unit using actual lignite-derived flue gas to evaluate various sorbent technologies for their effectiveness, performance, and cost. Testing under this project showed that halogenated ACs performed very well, with mercury capture rates often {ge} 90%. However, differences were noted between treated ACs with respect to reactivity and capacity, possibly as a result of storage conditions. Under certain conditions (primarily storage in ambient air), notable performance degradation had occurred in mercury capture efficiency. Therefore, a small exploratory task within this project evaluated possible differences resulting from storage conditions and subsequent effects of aging that …

A process has been developed for application of a thin, adherent vinyi plastic coating to graphite plates to prevent absorption of coupling fluids'' used in ultrasonic inspection. The plates are preheated and dipped mechanically in a fluid plastisol, and the resulting coating is fused in an infra-red heater. No significant attenuation of ultrasonic impulse results from presence of the coating. After inspection, the vinyl sheath may be easily stripped from the plate. (auth)

None

Summaries of meteorological observations collected at the Savannah River Site in 2004 show a year that was overall cooler and drier than average. Although the annual rainfall of 42.9 inches was the eleventh driest of all the years over a period of record that began in 1952, rainfall was quite variable through the year. September total rainfall of 10.26 inches was the highest in this 53 year record; conversely, the monthly rainfall in March, 0.81 inches, was the lowest on record. Rainfall of 0.01 inch or more occurred on 104 days during the year. The annual average temperature for 2004, 63.4 degrees F, was the eleventh coldest of any year in an available record that dates to 1964. Cooler than average conditions were observed in 9 of the 12 months of the year. The coldest temperature during the year was 20.3 degrees F on the morning of December 15; the warmest observed temperature was 98.2 degrees F on the afternoon of July 14. The most notable weather event of 2004 was an active Atlantic hurricane season that resulted in six named storms striking the Southeast U.S. during August and September. Although each of these storms posed a significant threat to …

Early neutral-beam injection is used in the National Spherical Torus Experiment (NSTX) to heat the electrons and slow current penetration which keeps q(0) elevated to avoid deleterious MHD activity and at the same time reduces Ohmic flux consumption, all of which aids long-pulse operation. However, the low plasma current (I{sub p} {approx} 0.5 MA) and electron density (n{sub e} {approx} 1 x 10{sup 13} cm{sup -3}) attending early injection lead to elevated orbit and shine through losses. The inherent orbit losses are aggravated by large excursions in the outer gap width during current ramp-up. An investigation of this behavior using various energetic particle diagnostics on NSTX and TRANSP code analysis is presented.

This meeting took place at the Keystone, Colorado resort from March 25-30, 2003. It was attended by 206 participants, of which 35 were students; 39% of attendees submitted abstracts. The meeting had 30% returning attendees and 70% new attendees. The group of speakers was composed of internationally recruited junior and senior experts in their respective fields. The group included representatives from academia and the private sector, highlights the convergence of proteomics efforts in the two sectors. The completion of the genome sequences of a large number of prokaryotic and eukaryotic species has catalyzed new research approaches to study the structure, function and control of biological processes. They are characterized by the systematic and in many cases quantitative analysis of all the molecules of a particular type expressed by a cell or tissue. The systematic analysis of proteins has been terms ''proteomics''. In an initial phase, most of the proteomics efforts were focused on large-scale protein identification. More recently, the objectives and technologies of proteomics have been diversified and expanded. Current proteomics research attempts to systematically and, where applicable, quantitatively determine the many properties of proteins and their biological function, including: protein abundance, state of modification, specific activity, interaction with other …

During the reporting period, work continued on development of formulations using the materials down-selected from the initially identified contenders for the fibrous monolith wear resistant components. In the previous reporting period, a two-stage binder removal process was developed that resulted in prototype parts free of voids and other internal defects. During the current reporting period, work was performed to characterize the two-stage binder removal process for WC-Co based FM material systems. Use of this process has resulted in the fabrication of defect free sintered WC-Co FM bodies, with minimal free carbon porosity and densities approaching 100% theoretical. With the elimination of free carbon porosity and other binder removal process related defects, development work focused on optimizing the densification and eliminating defects observed in WC-Co based FM consolidated by pressureless sintering. Shrinkage of the monolithic core and shell materials used in the WC-Co based FM system was measured, and differences in material shrinkage were identified as a potential cause of cell boundary cracking observed in sintered parts. Re-formulation of material blends for this system was begun, with the goal of eliminating mechanical stresses during sintering by matching the volumetric shrinkage of the core and shell materials. Thirty-three 7/8 inch drill bit …

The F-Canyon Facility was constructed in the early 1950's for the separation and recovery of 239Pu, 237Np and 238U from irradiated natural or depleted uranium targets and fuel rods using the PUREX (Plutonium - Uranium Extraction) process. In the PUREX process, the irradiated target or fuel slugs are received from the reactor areas of the Receiving Basin for Offsite Fuels, charged to the dissolvers and dissolved in nitric acid. The resulting solution contains primarily uranium-238 and smaller amounts of plutonium, uranium-235, and fission products. The primary operations conducted in F-Canyon include the separation and recovery of Pu-239 and U-238 from irradiated materials in the stabilization of plutonium residues. Since 1995, the F-Canyon Complex has been operating to stabilize ''at risk'' nuclear materials and spent fuel from throughout the DOE complex. That mission is complete. Since the last low level waste characterization, the F-Canyon has been implementing the PUREX Operations Suspension Plan and the Deactivation Project Plan.

None