Report presenting an investigation in the 19-foot pressure tunnel to determine the aerodynamic effects of several elevators with varying amounts of balance, of outboard split flaps, and of a droppable gas tank on a scale model of the F4U-1 airplane.

Report presenting testing of preformed copper fins which were furnace-brazed to a steel-cylinder barrel. The barrel was electrically heated and blower-cooled to determine heat overall heat-transfer coefficient. Information regarding potential future adaptations of the fins are provided.

"The results of flight investigations of the profile drag of several carefully finished conventional and low-drag airfoils are presented. The results indicated that in all cases lower profile-drag coefficients were obtained with the low-drag than with the conventional airfoils over the range of lift coefficient tested and that, for comparable conditions of lift coefficient and Reynolds number, the low-drag airfoils may have profile-drag coefficients which are at least 27 percent lower than the profile-drag coefficients of the conventional airfoils" (p.1).

Report presenting force tests of the NACA 23012 and 23012-64 airfoils of 24-inch chord in the high-speed wind tunnel at a range of Mach numbers. The results show the variation with mach number of lift, drag, and pitching-moment coefficients at a range of angles of attack.

Report presenting an investigation of the properties of a 20-inch diameter by 3.25 inch disc of 19-9 DL alloy in the as-forged and stress-relieved condition. Results regarding the hardness survey, short-time tensile properties, rupture test characteristics, time for deformation characteristics under stress, creep strengths, and stability characteristics are provided.

Test of a ducted body with Internal flow were made in the 8-foot high-speed wind tunnel for the purpose of studying the effects on external drag and an critical speed of the addition of efficient inlet and outlet openings to a basic streamline shape. Drag tests of a 13.6- inch-diameter streamline body of fineness ratio 6.14 were made at Mach numbers ranging from 0.20 to 0.75. The model was centrally mounted on a 9-percent-thick airfoil and was designed to have an efficient airfoil-body juncture and a high critical speed.

From Introduction: "The purpose of this report is to summarize, without extended proofs, the results of a study of a simplified model of nonadiabiatic, compressible fluid flow, both subsonic and supersonic, and to state these results in a form that will make them immediately useful in providing a theoretical background for current technical problems of high-speed combustion.

Report presenting an investigation of the stalling characteristics of the Supermarine Spitfire, which was made as part of the flying-qualities measurement of the airplane. The results are presented in the form of time histories of the motions and controls during stalls in various conditions of flight. Generally, the Spitfire possessed good stall warning in the form of buffeting and stall motions were not violent.

Report presenting a study of nitrided-steel piston rings in nitrided-steel cylinder barrels, which showed material of high reflectivity on their running faces. The structure of the material could not be resolved at a magnification of 1500 diameters. Results regarding the occurrence of coating, thickness of coating, height of coating above the nominal surface, chemical characteristics, physical characteristics, metallurgical change, and additional tests are provided.

Report presenting a series of boundary-layer surveys over the surface of an NACA 0012 airfoil at zero lift. Results regarding the pressure distribution, laminar boundary layer, transition, turbulent boundary layer, drag, and skin friction are provided.

Report presenting a method for the calculation of the external lift, moment, and pressure drag of slender open-nose bodies of revolution at supersonic speeds. The lift, moment, and pressure drag of a typical ramjet body shape are calculated at several Mach numbers. Results regarding the results of the calculations, comparison with experiment, and another application of the method are provided.

Report presenting the results of comparative cooling tests run on two Wright C9GC (G-200) cylinders, one with the original steel fins and one with 1-inch spiral copper fins brazed on the barrel. Calculations were also performed using copper and aluminum fins with the same weight as the original steel fins, which showed positive results. Results regarding cylinder-temperature correlation, piston-temperature correlation, and comparative performance are also provided.

Report presenting hinge moment, lift, and pressure-distribution measurements made on a Frise aileron on an NACA 23012 airfoil in the two-dimensional test section of the stability tunnel. Speeds up to 360 miles per hour corresponding to a Mach number of about 0.470 were used.

Report presenting an investigation of the flow downstream from a two-dimensional grid formed of parallel rods. The nature of the flow was determined primarily by means of total-head measurements. Preliminary tests were made in both the closed-duct and open, two-dimensional configurations, but it was found that the same phenomenon occurred in both cases.

Report presenting simple and exact expressions for the efficiency of single- and dual-rotating propellers with ideal circulation distribution as given by Goldstein functions for single-rotating propellers and by the new functions for dual-rotating propellers from part I of this series. Efficiency is found to depend primarily on a defined load factor and on an axial loss factor. Tables and graphs are included for practical use of the results.

From General Analysis: "The purpose of part I of this paper is to show how the loading that gives the minimum induced energy loss can be obtained from rather elementary considerations and to present design charts from which such a plan form can be quickly obtained for any set of design conditions."

Report presenting the results of a study of the rupture-test characteristics of 13 wrought and 4 cast alloys which were considered to have promise for service in exhaust gas turbines. The results are given in the forms of a table of information and data, a page of curves, and a page of photomicrographs.

Report presenting an analysis of available data on vee-tail surfaces. The analysis indicated that a vee tail designed to provide values of stability and control parameters equal to those provided by a conventional tail would probably provide no reduction in area unless the conventional vertical tail is in a bad canopy wake or unless the vee tail has a higher effective aspect ratio than the conventional vertical and horizontal tails.

Report presenting wind-tunnel tests in two-dimensional flow to investigate the aerodynamic characteristics of a double flap with an internal and overhang balance. Three sizes of each type of balance were tested with three relative rates of deflection of the two flaps. Results regarding lift, hinge moment, drag, and pitching moment are provided.

Report presenting an investigation of the effects of propeller operation on pitching moments with particular reference to the effect of propeller forces, the field of flow in the slipstream, and the increments of lift on the wing and the tail. A procedure, directly applicable only to single-engine monoplanes without flaps, has been set up for predicting the effect of propeller operation on pitching moments as well.

Report presenting an investigation of the effect of compressibility on the drag of a Bell P-39N-1 airplane in flight as part of a drag study on several high-speed airplanes for a range of Mach numbers.

Two-dimensional data were obtained in Mach range of from 0.40 to 0.94 and Reynolds Number range of (3.4 - 4.2) X 10 Degrees. Results indicate that thickness ratio is dominating shape parameter at high Mach numbers and that aerodynamic advantages are attainable by using thinnest possible sections. Effects of jet boundaries, Reynolds Number, and Data presented are free from jet-boundary and humidity effects.

Report presenting an investigation of the size and distribution of ice particles on the wings of aircraft and how they affect the aerodynamic characteristics. A simulated ice formation was generated from survey information received from aircraft pilots and was tested to determine the impact on the lift characteristics.

A theoretical investigation was conducted on jet-induced flow deviation. Analysis is given of flow inclination induced outside cold and hot jets and jet deflection caused by angle of attack. Applications to computation of effects of jet on longitudinal stability and trim are explained. Effect of jet temperature on flow inclination was found small when thrust coefficient is used as criterion for similitude. The average jet-induced downwash over tail plane was obtained geometrically.