Report presenting drag measurements made on a 10-percent-thick wing and 8-percent-thick tail and a 8-percent-thick wing, 6-percent-thick tail version of the X-1 airplane at a variety of Mach numbers. The drag of the thicker wing was found to be much higher than that of the thinner wing. The fuselage was found to cause interference with the wing of both models, making the separation of wing and fuselage drag difficult to determine.

The parameterization of the magnitude and the energy dependence of the E1 gamma-ray strength function for the calculation of neutron- and proton-induced capture cross sections and capture gamma-ray spectra is investigated. The energy-dependent Breit-Wigner (EDBW) is reparameterized incorporating a more general expression for the Breit-Wigner line shape. Evaluation of the reparameterized E1 gamma-ray strength function is discussed. (WHK)

The Seventh Annual Human Genome Conference: Beyond the Identification of Transcribed Sequences (BITS) was held November 16-19, 1997 at the Asilomar Conference Center in Monterey, California. The format for the meeting was a combination of oral presentations, group discussions and poster sessions. The original workshop was held to discuss methodologies for the identification of transcribed sequences in mammalian genomes. Over the years, the focus of the workshops has gradually shifted towards functional analysis, with the most dramatic change in emphasis at this meeting, as reflected in the modest change in the workshop title. Topics presented and discussed included: (1) large scale expression and mutational analysis in yeast, C. elegans, Drosophila and zebrafish, (2) comparative mapping of zebrafish, chicken and Fugu; (3) functional analysis in mouse using promoter traps, mutational analysis of biochemical pathways, and Cre/lox constructs; (4) construction of 5 foot end and complete cDNA libraries; (5) expression analysis in mammalian organisms by array screening and differential display; (6) genome organization as determined by detailed transcriptional mapping and genomic sequence analysis; (7) analysis of genomic sequence, including gene and regulatory sequence predictions, annotation of genomic sequence, development of expression databases and verification of sequence analysis predictions; and (8) structural/functional relationships …

It has often been reported that, in mass regions corresponding to peaks in the neutron strength function, nonstatistical mechanisms contribute a significant or even major portion of the average radiation width in the beginning of the resonance region. This could severely limit the possibility of calculating caputure cross sections for targets where experimental data are lacking, because such direct effects are sensitive to the detailed nuclear level structure in the daughter nucleus. The reaction /sup 98/Mo+n was examined for neutrons in the 1 keV to 3 MeV energy range, because this case is often cited as one of the clearest examples of valence neutron capture effects. Preliminary calculations are presented which suggest that these nonstatistical effects rapidly disappear when measurements from even a small number of resonances are averaged.

This report provides a summary of the demonstration project for development of a slant borehole to retrieve soil samples from beneath the SX-108 single-shell tank. It provides a summary of the findings from the demonstration activities and recommendations for tool selection and methods to deploy into the SX Tank Farm. Daily work activities were recorded on Drilling and Sampling Daily Work Record Reports. The work described in this document was performed during March and April 2000.

A stress analysis was performed on the LOFT Pressurizer Pressure Relief System to determine if it met the requirements of the ASME Boiler and Pressure Vessel Code, Section III, 1974 Edition, for Class 1 and Class 2 components. Deadweight, thermal expansion, seismic, design LOCE, and LOCA loads were considered. The results of this analysis indicate that the LOFT pressurizer pressure relief system will comply with Code specifications provided modifications are made to the hanger support configuration and one small section of pipe. The recommended changes are listed below. Note that some of these hangers were previously required based upon an analysis which subjected this same piping system to a reduced LOCE (20 millisecond valve opening). (1) Addition of Snubbers as per letter HIK-12-75, LOFT Pipe Hanger Requirements on Main Feed Main Steam Pressurizer and ECC Systems. (2) The 1/2'' Line 1/2''-PCS-10 between the tee and CVP-136-19 must be increased in diameter to 1.050 inches (OD of nominal 3/4'' pipe). (3) Modification of Unibals and flat bars as per letter Muff-2-76, required change of flat bar hangers and unibals on pressure relief and pressurizing piping. 9 refs., 6 figs., 1 tab.

The control system for the Nova laser must operate reliably in a harsh pulse power environment and satisfy requirements of technical functionality, flexibility, maintainability and operability. It is composed of four fundamental subsystems: Power Conditioning, Alignment, Laser Diagnostics, and Target Diagnostics, together with a fifth, unifying subsystem called Central Controls. The system architecture utilizes a collection of distributed microcomputers, minicomputers, and components interconnected through high speed fiber optic communications systems. The design objectives, development strategy and architecture of the overall control system and each of its four fundamental subsystems are discussed. Specific hardware and software developments in several areas are also covered.

None

Nearly half of the US utility-owned steam electric generating capacity is cooled by once-through cooling systems. These plants withdraw cooling water primarily from surface water bodies. Section 316(b) of the Clean Water Act requires that the location, design, construction, and capacity of cooling water intake structures reflect the best technology available (BTA) for minimizing adverse environmental impacts. At present, the US Environmental Protection Agency (EPA) has not yet promulgated applicable implementing regulations governing intake structures; however, the Agency is required by a Consent Decree to develop such regulations. EPA has presented a draft tiered regulatory framework approach that, depending on site-specific factors, may impose various regulatory burdens on affected utilities. Potential new requirements could range from compiling and submitting existing data to demonstrate that existing conditions at each unit represent BTA to retrofitting plants with closed-cycle cooling systems (primarily cooling towers). If the final regulations require installation of cooling towers or implementation of other costly plant modifications, utilities may elect to close some generating units rather than invest the finds necessary to upgrade them to meet the Section 316(b) requirements. Potentially, some regions of the country may then have a higher proportion of closed units than others, leading to a …

The Power Systems Development Facility (PSDF) is a joint Department of Energy/Industry sponsored engineering-scale facility for testing advanced coal-based power generation technologies. High temperature, high pressure gas cleaning is critical to many of these advanced technologies. Barrier filter elements that can operate continuously for nearly 9000 hours are required for a successful gas cleaning system for use in commercial power generation. Since late 1999, the Kellogg Brown & Root Transport reactor at the PSDF has been operated in gasification mode. This paper describes the test results for filter elements operating in the Siemens-Westinghouse particle collection device (PCD) with the Transport reactor in gasification mode. Operating conditions in the PCD have varied during gasification operation as described elsewhere in these proceedings (Martin et al, 2002).

Understanding global-scale ecosystem responses to changing environmental conditions is important both as a scientific question and as the basis for making policy decisions. The confidence in regional models depends on how well the field data used to develop the model represent the region of interest, how well the environmental model driving variables (e.g., vegetation type, climate, and soils associated with a site used to parameterize ecosystem models) represent the region of interest, and how well regional model predictions agree with observed data for the region. To assess the accuracy of global model forecasts of terrestrial carbon cycling, two Ecosystem Model-Data Intercomparison (EMDI) workshops were held (December 1999 and April 2001). The workshops included 17 biogeochemical, satellite-driven, detailed process, and dynamic vegetation global model types. The approach was to run regional or global versions of the models for sites with net primary productivity (NPP) measurements (i.e., not fine-tuned for specific site conditions) and analyze the model-data differences. Extensive worldwide NPP data were assembled with model driver data, including vegetation, climate, and soils data, to perform the intercomparison. This report describes the compilation of NPP estimates for 2,523 sites and 5,164 0.5{sup o}-grid cells under the Global Primary Production Data Initiative (GPPDI) …

Sum frequency generation (SFG) surface vibrational spectroscopy was used to characterize interfaces pertinent to current surface engineering applications, such as thin film polymers and novel catalysts. An array of advanced surface science techniques like scanning probe microscopy (SPM), x-ray photoelectron spectroscopy (XPS), gas chromatography (GC) and electron microscopy were used to obtain experimental measurements complementary to SFG data elucidating polymer and catalyst surface composition, surface structure, and surface mechanical behavior. Experiments reported in this dissertation concentrate on three fundamental questions: (1) How does the interfacial molecular structure differ from that of the bulk in real world applications? (2) How do differences in chemical environment affect interface composition or conformation? (3) How do these changes correlate to properties such as mechanical or catalytic performance? The density, surface energy and bonding at a solid interface dramatically alter the polymer configuration, physics and mechanical properties such as surface glass transition, adhesion and hardness. The enhanced sensitivity of SFG at the buried interface is applied to three systems: a series of acrylates under compression, the compositions and segregation behavior of binary polymer polyolefin blends, and the changes in surface structure of a hydrogel as a function of hydration. In addition, a catalytically active thin …

Computational chemists are using Common Component Architecture (CCA) technology to increase the parallel scalability of their application ten-fold. Combustion researchers are publishing science faster because the CCA manages software complexity for them. Both the solver and meshing communities in SciDAC are converging on community interface standards as a direct response to the novel level of interoperability that CCA presents. Yet, there is much more to do before component technology becomes mainstream computational science. This paper highlights the impact that the CCA has made on scientific applications, conveys some lessons learned from five years of the SciDAC program, and previews where applications could go with the additional capabilities that the CCA has planned for SciDAC 2.

Each year, thousands of new oil and gas wells are drilled in the United States and around the world. The drilling process generates millions of barrels of drilling waste each year, primarily used drilling fluids (also known as muds) and drill cuttings. The drilling wastes from most onshore U.S. wells are disposed of by removing the liquids from the drilling or reserve pits and then burying the remaining solids in place (called pit burial). This practice has low cost and the approval of most regulatory agencies. However, there are some environmental settings in which pit burial is not allowed, such as areas with high water tables. In the U.S. offshore environment, many water-based and synthetic-based muds and cuttings can be discharged to the ocean if discharge permit requirements are met, but oil-based muds cannot be discharged at all. At some offshore facilities, drilling wastes must be either hauled back to shore for disposal or disposed of onsite through an injection process.

In 1981, the joint ORNL/PPPL PDX neutral beam heating project succeeded in reliably injecting 7.2 MW of D/sup 0/ into the PDX plasma, at nearly perpendicular angles, and achieved ion temperatures up to 6.5 keV. The expeditious achievement of this result was due to the thorough conditioning and qualification of the PDX neutral beam ion sources at ORNL prior to delivery coupled with several field design changes and improvements in the injection system made at PPPL as a result of neutral beam operating experience with the PLT tokamak. It has been found that the operation of high power neutral beam injection systems in a tokamak-neutral beam environment requires procedures and performance different from those required for development operation on test stands. In this paper, we review the installatin of the PDX neutral beam injection system, and its operation and performance during the initial high power plasma heating experiments with the PDX tokamak.

We have begun building the ''Mercury'' laser system as the first in a series of new generation diode-pumped solid-state lasers for inertial fusion research. Mercury will integrate three key technologies: diodes, crystals, and gas cooling, within a unique laser architecture that is scalable to kilojoule energy levels for fusion energy applications. The primary performance goals include 10% electrical efficiencies at 10 Hz and 100 J with a 2-10 ns pulse length at 1.047 pm wavelength. When completed, Mercury will allow rep-rated target experiments with multiple target chambers for high energy density physics research.

This report describes a project sponsored by the U.S. Department of Energy (DOE) and implemented by the Pacific Northwest National Laboratory (PNNL), from 2000 to 2007 to improve the performance of reflector type (R-lamp) compact fluorescent lamps (CFLs) and increase their availability throughout the United States by means of a technology development and procurement strategy. In 2000, at the request of the U.S. Department of Energy’s Emerging Technologies Program and its predecessors, the Pacific Northwest National Laboratory undertook a technology procurement seeking R-CFLs that were specifically designed for use in ICAT recessed can fixtures and that met other minimum performance criteria including minimum light output and size restrictions (to ensure they fit in standard residential recessed cans). The technology procurement included two phases. In Phase I, requests for proposals (RFPs) were issued in October 2002 and five manufacturers responded with 12 lamp models. Eight of these models met the minimum requirements and passed the 6-hour short-term test in a simulated ICAT environment. These eight models were subjected to long-term tests of 6,000 or more hours in a simulated ICAT environment. Three of these models passed the short- and long-term tests and were promoted through the program website (www.pnl.gov/rlamps), press releases, …

This report looks at the background of Trade Adjustment Assistance (TAA) in the Trade Expansion Act of 1962, which was created by Congress. It then discusses how the 112th Congress is considering legislative action to extend the TAA - including two issues: how necessary or appropriate the extension is, and whether or not three proposed bills should be voted upon separately.

SNL-9 (permitted by the State Engineer as C-2950) was drilled to provide geological data and hydrological testing of the Culebra Dolomite Member of the Permian Rustler Formation within a proposed re-entrant of the margin of halite dissolved from the upper part of the Salado near Livingston Ridge. SNL-9 is located in the southeast quarter of section 23, T22S, R30E, in eastern Eddy County, New Mexico. SNL-9 was drilled to a total depth of 845 ft below the ground surface. Below surface dune sand and the Berino soil, SNL-9 encountered, in order, the Mescalero caliche, Gatuna, Dewey Lake, Rustler, and uppermost Salado Formations. Two intervals were cored: 1) from the lower Forty-niner Member through the Magenta Dolomite and into the upper Tamarisk Member; and 2) from the lower Tamarisk Member through the Culebra Dolomite and Los Meda?os Members and into the uppermost Salado Formation. Geophysical logs were acquired from the open hole to total depth, and the drillhole was successfully completed with a screened interval open across the Culebra.

SNL-2 was drilled in the northwest quarter of Section 12, T22S, R30E, in eastern Eddy County, New Mexico (Figure 2-1). It is located 574 ft from the north line (fnl) and 859 ft from the west line (fwl) of the section (Figure 2-2). This location places the drillhole east of the Livingston Ridge escarpment among oil wells of the Cabin Lake field. SNL-2 will be used to test hydraulic properties and to monitor ground water levels of the Culebra Dolomite Member of the Permian Rustler Formation. SNL-2 was permitted by the New Mexico State Engineer as C-2948. [Official correspondence regarding permitting and regulatory information must reference this permit number.] In the plan describing the integrated groundwater hydrology program (Sandia National Laboratories, 2003), SNL-2 is also codesignated WTS-1 because the location also satisfies needs for long-term monitoring of water quality and movement in the Culebra Dolomite for RCRA permitting; this program is under the management of Washington TRU Solutions LLC (WTS). In the event that additional wells are established on the SNL-2 drillpad to monitor other hydrological units (e.g., the Magenta Dolomite Member of the Permian Rustler Formation), the current drillhole will likely be referred to as SNL-2C because it is …

SNL-1 (permitted by the New Mexico State Engineer as C-2953) was drilled to provide geological data and hydrological testing of the Culebra Dolomite Member of the Permian Rustler Formation near the margin of dissolution of halite in the upper Permian Salado Formation in the northeast arm of Nash Draw. SNL-1 is located in the northwest quarter of section 16, T21S, R31E, in eastern Eddy County, New Mexico, and it is adjacent to the tailings pile of Mississippi Potash Incorporated (now Intrepid) East mine to test for the presence of shallow zones that might include brine infiltrated from the tailings pile. SNL-1 was drilled to a total depth of 644 ft below ground level (bgl). Below surface wash, SNL-1 encountered, in order, the Mescalero caliche, Dewey Lake, and Rustler Formations.

This report was funded by the U.S. Department of Energy's (DOE's) National Energy Technology Laboratory (NETL) Existing Plants Research Program, which has an energy-water research effort that focuses on water use at power plants. This study complements the Existing Plants Research Program's overall research effort by evaluating water issues that could impact power plants. Water consumption by all users in the United States over the 2005-2030 time period is projected to increase by about 7% (from about 108 billion gallons per day [bgd] to about 115 bgd) (Elcock 2010). By contrast, water consumption by coal-fired power plants over this period is projected to increase by about 21% (from about 2.4 to about 2.9 bgd) (NETL 2009b). The high projected demand for water by power plants, which is expected to increase even further as carbon-capture equipment is installed, combined with decreasing freshwater supplies in many areas, suggests that certain coal-fired plants may be particularly vulnerable to potential water demand-supply conflicts. If not addressed, these conflicts could limit power generation and lead to power disruptions or increased consumer costs. The identification of existing coal-fired plants that are vulnerable to water demand and supply concerns, along with an analysis of information about their …

We report results from the first experiments to explore the evolution of the Rayleigh-Taylor (RT) instability from intentionally three-dimensional (3D) initial conditions at an embedded, decelerating interface in a high-Reynolds-number flow. The experiments used {approx}5 kJ of laser energy to produce a blast wave in polyimide and/or brominated plastic having an initial pressure of {approx}50 Mbars. This blast wave shocked and then decelerated the perturbed interface between first material and a lower-density, C foam. This caused the formation of a decelerating interface with an Atwood number {approx}2/3, producing a long-term positive growth rate for the RT instability. The initial perturbations were a 3D perturbation in an ''egg-crate'' pattern with feature spacings of 71 {micro}m in two orthogonal directions and peak-to-valley amplitudes of 5 {micro}m. The resulting RT spikes were observed to overtake the shock waves at the undisturbed, ''free-fall'' rate, and to subsequently deliver material from behind the interface to the forward shock. This result is unanticipated by prior simulations and models.

Report presenting the design of a two-stage, solid-fuel, rocket-propelled, general research pilotless aircraft suitable for investigating stability and control at supersonic velocities. The flight test investigation is described and information is provided for zero-length launchers and operational flight-test techniques of two-stage rockets. Results regarding launching characteristics and lateral stabilization and control flight tests are provided.