Ions from EBIS are injected into Booster after acceleration by an RFQ and a Linac. The velocity of the ions at Booster injection is c{beta} where c is the velocity of light and (1) {beta} = 0.0655. The kinetic energy is (2) W = mc{sup 2}({gamma}-1) where m is the ion mass and (3) {gamma} = (1-{beta}{sup 2}){sup -1/2}. Putting in numbers one gets a kinetic energy of approximately 2 MeV per nucleon for each ion. The revolution period at injection is 10.276 {micro}s. The ions in the EBIS trap are delivered in a beam pulse that ranges from 10 to 40 {micro}s in length. This amounts to 1 to 4 turns around the machine. The transverse emittance (un-normalized) of EBIS beams just prior to injection into Booster is 11{pi} mm milliradians in both planes. This is an order of magnitude larger than the nominal 1{pi} mm milliradians for Tandem beams. Injection proceeds by means of an electrostatic inflector in the C3 straight section and four programmable injection dipoles in the C1, C3, C7, and D1 straights. These devices have been in use for many years for the injection of ions from Tandem as described in [1] and [2]. The …

In order to treat the mixed radioactive and hazardous waste stored in 177 underground tanks, the Tank Waste Remediation System (TWRS) program is developing a `demonstration` site for treatment and immobilization of these wastes by a private contractor. Project W-519 is providing the infrastructure support to this site by developing the designs and emplacing required pipelines, roads, electrical, etc. In support of the TWRS Phase 1 Infrastructure Project (W-519) Characterization, Numatec Hanford Corporation (NHC) contracted with Waste Management Federal Services, Inc., Northwest Operations (WMNW) to investigate a number of locations in and just outside the 200 East Area eastern fenceline boundary. These areas consisted of known or suspected waste lines or waste sites that could potentially impact the construction and emplacement of the proposed facility improvements, including waterlines and roads. These sites were all located subsurface and sugaring would be required to obtain sample material from the desired depth. The soils would then be sampled and submitted to the laboratory for analysis of radioactivity.

N/A

N/A

N/A

N/A

Neutron-induced capture cross sections for the ground states and first isomeric states of /sup 93/Nb, /sup 94/Nb and /sup 95/Nb were studied from the resolved resonance region to 4 MeV via statistical model calculations. The production of isomers was included. Inelastic scattering cross sections and gamma-ray production spectra were also calculated. The anti GAMMA/ sub ..gamma..//D ratios were derived from gamma-ray strength function systematics. Total capture cross sections on the ground states are found to be within a factor of two of each other. Capture cross sections on the isomeric targets are important as well, not only because of their magnitude but also because of the significant population of these isomeric levels by inelastic scattering. 10 references.

This report describes the existing and proposed methodologies for performing measurements of contamination prior to releasing material for uncontrolled use at the Hanford Site. The technical basis for the proposed methodology, a modification to the existing contamination survey protocol, is also described. The modified methodology, which includes a large-area swipe followed by a statistical survey, can be used to survey material that is unlikely to be contaminated for release to controlled and uncontrolled areas. The material evaluation procedure that is used to determine the likelihood of contamination is also described.

This report contains geologic, geochemical, and physical characterization data collected on sediment recovered from boreholes C4104 and C4105 in the T Tank Farm, and 299-W-11-39 installed northeast of the T Tank Farm. The measurements on sediments from borehole C4104 are compared to a nearby borehole 299-W10-196 placed through the plume from the 1973 T-106 tank leak. This report also presents the data in the context of sediment types, the vertical extent of contamination, the migration potential of the contaminants, and the likely source of the contamination in the vadose zone and groundwater below the T Tank Farm. Sediment samples were characterized for: moisture content, gamma-emission radionuclides, one-to-one water extracts (which provide soil pH, electrical conductivity, cation, trace metal, radionuclide and anion data), total carbon and inorganic carbon content, and 8 M nitric acid extracts (which provide a measure of the total leachable sediment content of contaminants). Overall, our analyses showed that common ion exchange is a key mechanism that influences the distribution of contaminants within that portion of the vadose zone affected by tank liquor. We observed slight elevated pH values in samples from borehole C4104. The sediments from the three boreholes, C4104, C4105, and 299-W10-196 do show that sodium-, …

This report was revised in September 2008 to remove acid-extractable sodium data from Tables 4.8, 4.28, and 4.52. The sodium data was removed due to potential contamination introduced during the acid extraction process. The rest of the text remains unchanged from the original report issued in September 2004. The overall goal of the Tank Farm Vadose Zone Project, led by CH2M HILL Hanford Group, Inc., is to define risks from past and future single-shell tank farm activities at Hanford. To meet this goal, CH2M HILL Hanford Group, Inc. tasked scientists from Pacific Northwest National Laboratory to perform detailed analyses on vadose zone sediments from within Waste Management Area (WMA) T-TX-TY. This report is the second of two reports written to present the results of these analyses. Specifically, this report contains all the geologic, geochemical, and selected physical characterization data collected on vadose zone sediment recovered from boreholes C4104 and C4105 in the T Tank Farm, and from borehole 299-W-11-39 installed northeast of the T Tank Farm. Finally, the measurements on sediments from borehole C4104 are compared with a nearby borehole drilled in 1993, 299- W10-196, through the tank T-106 leak plume.

One of the hallmarks of linear coupling is the resonant exchange of oscillation amplitude between the horizontal and vertical planes when the difference between the unperturbed tunes is close to an integer. The standard derivation of this phenomenon (known as the difference resonance) can be found, for example, in the classic papers of Guignard [1, 2]. One starts with an uncoupled lattice and adds a linear perturbation that couples the two planes. The equations of motion are expressed in hamiltonian form. As the difference between the unperturbed tunes approaches an integer, one finds that the perturbing terms in the hamiltonian can be divided into terms that oscillate slowly and ones that oscillate rapidly. The rapidly oscillating terms are discarded or transformed to higher order with an appropriate canonical transformation. The resulting approximate hamiltonian gives equations of motion that clearly exhibit the exchange of oscillation amplitude between the two planes. If, instead of the hamiltonian, one is given the four-by-four matrix for one turn around a synchrotron, then one has the complete solution for the turn-by-turn (TBT) motion. However, the conditions for the phenomenon of amplitude exchange are not obvious from a casual inspection of the matrix. These conditions and those …

One cannot expect measurements alone to supply all of the neutron-induced activation cross-section data required by the fission reactor, fusion reactor, and nuclear weapons development communities, given the wide ranges of incident neutron energies, the great variety of possible reaction types leading to activation, and targets both stable and unstable. Therefore, the evaluator must look to nuclear model calculations and systematics to aid in fulfilling these cross-section data needs. This review presents some of the recent developments and improvements in the prediction of neutron activation cross sections, with specific emphasis on the use of empirical and semiempirical methods. Since such systematics require much less nuclear informaion as input and much less computational time than do the multistep Hauser-Feshbach codes, they can often provide certain cross-section data at a sufficient level of accuracy within a minimum amount of time. The cross-section information that these systematics can and cannot provide and those cases in which they can be used most reliably are discussed.

We report on our investigation of the Rayleigh-Taylor (R-T) and Kelvin-Helmholtz (K-H) instabilities in laser ablatively accelerated targets for single mode perturbations for a series of wavelengths in the parameter regime 1/2 less than or equal to lambda/..delta..R less than or equal to 10, where lambda is the wavelength of the perturbation and ..delta..R is the cold foil thickness. We find linear growth rates well below classical values (by a factor on the order of 3 to 4). We also find a cutoff in the growth rates for wavelengths less than the foil thickness. The striking result is the dominance of nonlinear effects; i.e., the K-H instability, for short wavelength perturbations. Although the linear growth rates increase as k/sup 1/2/ up to the cutoff, the K-H rollup dominates at large k, drastically reducing the penetration rate of the dense spike below its free fall value and effectively doubling the aspect ratio of the foil. In other words, it is the long wavelength perturbations that are most effective in destroying the symmetric implosion of the shell.

Ten closely spaced, shallow (<100 ft) drill cores were obtained from the 1.22-Ma-old Bandelier Tuff at a 4-acre site for proposed construction at Los Alamos National Laboratory, New Mexico. The goal of the investigation was to identify faults that may have potential for earthquake-induced surface ruptures at the site. Careful mapping of contact surfaces within the Bandelier Tuff was supplemented with results of geochemical analyses to establish unit boundaries with a high degree of accuracy. Analysis shows that the upper contact surface of Unit 3 of the Bandelier Tuff provides no evidence of faults beneath the building site, and that the subsurface structure is consistent with a shallowly dipping (< 2{degree}), unbroken block. Because no significant or cumulative faulting events have disturbed the site in the last 1.22 million years, it is unlikely that surface rupture will occur at the site in future large earthquakes. Uncertainty analysis suggests that this method would detect faults with {ge}2 ft of cumulative stratigraphic separation.

The authors present a measurement of the fraction f{sub +} of right-handed W bosons produced in top quark decays, based on a candidate sample of t{bar t} events in the {ell}+jets and dilepton decay channels corresponding to an integrated luminosity of 370 pb{sup -1} collected by the D0 detector at the Fermilab Tevatron p{bar p} Collider at {radical}s = 1.96 TeV. They reconstruct the decay angle {theta}* for each lepton. By comparing the cos{theta}* distribution from the data with those for the expected background and signal for various values of f{sub +}, they find f{sub +} = 0.056 {+-} 0.080(stat) {+-} 0.057(syst). (f{sub +} < 0.23 at 95% C.L.), consistent with the standard model prediction of f{sub +} = 3.6 x 10{sup -4}.

Recent studies indicate LaBr3(Ce) scintillation detectors have desirable attributes, such as room temperature operability, which may make them viable alternatives as primary detectors (PD) in a Compton suppression spectrometer (CSS) used for remote-handled transuranic (RH-TRU) waste assay. A CSS with a LaBr3(Ce) PD has been designed and its expected performance evaluated using Monte Carlo analysis. The unique design of this unit minimizes the amount of "dead" material between the PD and the secondary guard detector. The analysis results indicate that this detector will have a relatively high Compton-suppression capability, with greater suppression ability for large angle-scattered photons in the PD. J. K. Hartwell1, M. E. McIlwain1, R. P. Gardner2, J. Kulisek3 1) Idaho National Laboratory, PO Box 1625, Idaho Falls, ID 83415-2114 USA 2) North Carolina State University, Dept of Nuclear Eng., PO Box 7909, Raleigh, NC 27695 USA 3) Ohio State University, Columbus, Ohio 43210 The US Department of Energy’s transuranic (TRU) waste inventory includes about 4,500 m3 of remote-handled TRU (RH-TRU) wastes. The RH-TRU waste stream is composed of a variety of containerized waste forms having a contact surface dose rate that exceeds 2 mSv/hr (200 mrem/hr) containing waste materials with a total TRU concentration greater than 3700 …

Experimental measurements were made of the production cross sections and energy distributions of gamma rays emitted when the stable targets /sup 88/Sr, /sup 89/Y and /sup 90/Zr are exposed to protons in the energy range 3 to 8 MeV. The data are being analyzed using a recent version of the Uhl statistical model code. One conclusion is that while the gamma-ray strength functions employed reproduce the proton capture cross sections, they do not achieve the same degree of hardness observed in the measured spectra. To do so, their lower energy regions must be modified; such changes, however, do not affect the capture cross sections. 7 references.

This report was revised in September 2008 to remove acid-extractable sodium data from Tables 4.15 and 4.19. The sodium data was removed due to potential contamination introduced during the acid extraction process. The rest of the text remains unchanged from the original report issued in February 2002. The Tank Farm Vadose Zone Project is led by CH2M HILL Hanford Group, Inc. Their goals include defining risks from past and future single-shell tank farm activities, identifying and evaluating the efficacy of interim measures, and collecting geotechnical information and data. The purpose of these activities is to support future decisions made by the U.S. Department of Energy (DOE) regarding near-term operations, future waste retrieval, and final closure activities for the single-shell tank Waste Management Areas. To help in this effort, CH2M HILL Hanford Group, Inc. contracted with scientists at Pacific Northwest National Laboratory to analyze sediment samples collected from borehole 299-W23-19.

The Booster synchrotron at Brookhaven National Laboratory has been incorporated into the accelerator chain at the Alternating Gradient Synchrotron (AGS) complex. After a successful first commissioning effort in the spring of 1991, the Booster has been part of this year`s silicon, gold and proton physics runs. After a brief review of the Booster design goals, and of the early commissioning, this paper will summarize this year`s activities.

Hydrous Metal Oxides (HMOs) are chemically synthesized materials which contain a homogeneous distribution of ion exchangeable alkali cations that provide charge compensation to the metal-oxygen framework. Both the presence of these alkali cations and the resulting high cation exchange capacities (4-5 meq/g) clearly set these HMO materials apart from conventional precipitated hydrous oxides. For catalyst applications, the HMO material serves as an ion exchangeable support which facilitates the uniform incorporation of catalyst precursor species. Following catalyst precursor incorporation, an activation step is required to convert the catalyst precursor to the desired active phase. Considerable process development activities at Sandia National Laboratories related to HMO materials have resulted in bulk silica-doped hydrous titanium oxide (HTO:Si)-supported NiMo catalysts that are more active in model compound reactions than commercial NiMo catalysts. These reactions, e.g. pyrene hydrogenation, simulate direct coal liquefaction. However, extension of this process to produce NiMo/HTO:Si catalyst coatings on commercial supports is of interest for liquefaction applications since overall catalyst cost can be reduced and bulk HTO:Si mechanical limitations can be circumvented. In the present effort, NiMo/HTO:Si has been evaluated for hydrodesulfurization (HDS) and hydrodenitrogenation (HDN) of coal derived liquids. NiMo/HTO:Si catalysts have been evaluated in both bulk (unsupported) form and …

The feasibility of using the KEWB reactor as a pulsed neutron radiation source for use in studies of fuel element transient heating was studied. UC fuel rod samples were heated in the reactor. It was found that flux distribution in fuel samples could be mapped and thermal conductivity measurements for UC could be made by using fast response thermocouples distributed radially in the sample. (J. R.D.)

This report was revised in September 2008 to remove acid-extractable sodium data from Tables 4.8, 4.28,4.43, and 4.59. The sodium data was removed due to potential contamination introduced during the acid extraction process. The rest of the text remains unchanged from the original report issued in April 2004. The overall goal of the Tank Farm Vadose Zone Project, led by CH2M HILL Hanford Group, Inc., is to define risks from past and future single-shell tank farm activities at Hanford. To meet this goal, CH2M HILL Hanford Group, Inc. tasked scientists from Pacific Northwest National Laboratory to perform detailed analyses on vadose zone sediments from within Waste Management Area (WMA) T-TX-TY. This report is the first of two reports written to present the results of these analyses. Specifically, this report contains all the geologic, geochemical, and selected physical characterization data collected on vadose zone sediment recovered from boreholes C3830, C3831, and C3832 in the TX Tank Farm, and from borehole 299-W-10-27 installed northeast of the TY Tank Farm.

Tungsten in uranium--tungsten alloys is determined by precipitating the tungsten from a cold sulfuric acid solution using alpha -benzoinoxime and cinchonine as the precipitating agents. The precipitate is dgnited at 800 deg C and weighed as WO/sub 3/. Results of 94 determinations on known samples containing 20 to 40 milligrams of tungsten in the presence of 1 to 8 grams of uranium showed an average recovery of 100.1% with a standard deviation of 0.7%. (auth)

In 2003, the National Association of Regulatory Utility Commissioners (NARUC) and National Energy Technology Laboratories (NETL) collaboratively established the International Clean Energy Coalition (ICEC). The coalition consisting of energy policy-makers, technologists, and financial institutions was designed to assist developing countries in forming and supporting local approaches to greenhouse gas mitigation within the energy sector. ICEC's work focused on capacity building and clean energy deployment in countries that rely heavily on fossil-based electric generation. Under ICEC, the coalition formed a steering committee consisting of NARUC members and held a series of meetings to develop and manage the workplan and define successful outcomes for the projects. ICEC identified India as a target country for their work and completed a country assessment that helped ICEC build a framework for discussion with Indian energy decisionmakers including two follow-on in-country workshops. As of the conclusion of the project in 2010, ICEC had also conducted outreach activities conducted during United Nations Framework Convention on Climate Change (UNFCCC) Ninth Conference of Parties (COP 9) and COP 10. The broad goal of this project was to develop a coalition of decision-makers, technologists, and financial institutions to assist developing countries in implementing affordable, effective and resource appropriate technology and …