Leach liquors produced from Utex ore by cold leaching, hot leaching and pugging proved amenable to the ion exchange process. In addition, a resin-in-pulp system was operated using the Lucite Winchester sells on Utex pulp produced by cold leaching.

Second and third tests were conducted on an expansion bellows and Zircaloy-stainless steel transition joint assembly, duplicating that used in the core-pressure vessel assembly of the HRT. The assembly was exposed for 1140 hours in the second test and and 167 hours in the third to a solution containing 0.04m UO2SO4, 0.02m H2SO4, and 0.005m CuSO4 in a 100A dynamic corrosion loop under conditions simulating reactor startup, shutdown, and steady-state operation. Results indicated that the transition joint assembly as tested was mechanically sound and leak-tight. Pit-type corrosion continued on the expansion bellows where the upper retaining tangent contacts the bellows. Results are included of specimens exposed to the circulation solution during transition joint and bellows test.

Quarterly report describing progress on the EVESR Nuclear Superheat Fuel Development Project.

The new and as yet unsolved problems introduced by the production of large quantities of fission products and radioactive isotopes from fission or neutron capture present mankind a most complex technical, economic, and political problem. On one hand, the possibility of using the fission process to produce energy from an unexploited and abundant natural source is emerging from large programs of research and development. We are also beginning to see the promise of use of particulate and electromagnetic radiation for the good of man. On the other hand, we are presented with the problem of controlling the dangerous products of fission for periods of time measured in terms of many hundreds of years, periods longer than the effective tenure of any political state in history. We must not only devise ways of protecting ourselves in the present and for our lifetime but, in addition, we must establish the basic technical, social, and administrative control of vast quantities of artificial radioactivity that must remain effective for at least ten to twenty lifetimes.

Tables of the electron pressure and kinetic energy for a partially degenerate, relativistic, ideal electron gas are computed by numerical integration using an IBM 7090 electronic calculator. These are given in terms of log10(B) and log10(0), where B is the ratio of the temperature to the rest mass of the electron and (O) is proportional to the numerical density of electrons. The tables include values of T from 5 million to 400 billion degrees and cover the range of electron densities from the region of a perfect gas to the region of complete degeneracy.

"Helium, nitrogen, carbon dioxide, and other gases suitable as reactor coolants were evaluated. It is shown that because of the helium conservation program, recently authorized by legislation, sufficient helium will become available for domestic power plants and for the requirements of the Euratom group. Tables of thermodynamic properties for helium and molecular nitrogen were computed from the Beattie-Bridgman equation of state. Specific enthalpy, specific entropy, isobaric specific heat, specific heat ratio, compressibility factor, specific volume, and acoustic velocity are tabulated over the range helium and molecular nitrogen are given."

The experimental demonstration of fission product release from over heated reactor fuel is necessarily subject in many respects to the arbitrary conditions imposed by the experimenter. Since an almost infinite latitude exists in the choice of materials, atmospheres, gas, velocities, temperatures etc., some allowance for an extrapolation to alternate conditions is definitely in order. The conditions imposed in this study are best described as those most likely to maximize fission product release. Two of the most important variables not investigated in the present report are the influence of metal cladding and the difference in internal nuclear heating as opposed to external radiant heating. In addition a significant uncertainty exists in the understanding of diffusion through large masses such as might result from a scaled-up melt down in a reactor.

Technical report was prepared by the Health and Safety Laboratory (HASL) with the objective of presenting a current picture of the Strontium Program. Abstract: Strontium 90 levels in fallout, milk, canned fish and tap water are summarized for data available up to September 15, 1957. Original data submitted during the month of September is included as an appendix. Data are presented to show the amount of Strontium 90 in fallout at sampling stations within and outside the United States.

The following report concerns the application of a relaxation mesh method for the determination of the average flux within the moderator of a light water moderated, 1.027 per cent U-235, hexagonal lattice with a volume ratio (V_H2O + V_Al)/V_Uranium of 4:1. It was hoped that the calculation would enable one to determine any differences in flux which might result from the fact that the unit cell is a hexagon instead of a cylinder. Because we were primarily interested in the effect due to geometry we applied the same theory, diffusion theory, to the hexagon by means of the mesh method and to the equivalent cylinder.

Technique used in deriving values of the linac ball tuner settings to produce various fields is discussed briefly, and tables showing ball tuner change numbers and values used in making up the ball tuner change numbers are given.

The lubrication equations for an arbitrary Newtonian fluid are derived directly from the general equations for conservation of mass, momentum, and energy. From the lubrication equations an inequality is obtained for the internal film temperature rise, after which the isothermal film equations are derived. Then, for perfectly-aligned self-acting journal bearings, a conservation equation is obtained. For gas bearings this condition gives: [formula] constant along the axis of the bearing. Application of this condition to the infinitely-long gas bearing gives more accurate pressure solutions for this case. The Katto-Soda form of the differential equation for the infinitely-long bearing is solved by a series expansion in the eccentricity ratio, the first terms of which give the original, approximate Katto-Soda solution. In addition, solutions obtained numerically by digital computations are presented in graphical and tabular form for eccentricity ratios from 0 to 0.9 and compressible bearing parameter [formula]. Design charts based on these calculations are provided.

Report detailing the results of several yttrium oxide analyses. Four different institutions were given 50 grams of yttrium oxide to analyze following the Yttrium Analytical Conference on November 7th and 8th, 1956. This report details the results of those four different institutions.

Abstract: Residual and fission gas release from UO2 were studied in the laboratory and in in-reactor experiments. Arc-fused powder and sintered pellets were used to determine the rate of evolution and types of residual gases as a function of temperature. Fission gas release was related to the average UO2 temperature and fission gas release calculations were made using the latest thermal conductivity values, isotopic half lives, and branching ratios available in the literature. The results obtained were compared with those available in the literature, and a satisfactory agreement was found among the groups of comparable data.

Quarterly report discussing progress on the Fast Ceramic Reactor Development Program, "an integrated analytical and experimental program directed toward the development of fast reactors employing ceramic fuels, with particular attention to mixed plutonium-uranium oxide" (p. 1).

Construction of the HRT reactor shield tank was completed, and the inside surfaces were painted. The roof structure for the tank is being assembled in preparation for an acceptance pressure test. Service piping and instrument lines are being installed in the central room area by ORNL craft forces. This work is approximately 50% complete. Fabrication of all temperature system components, except the blanket outer storage tanks, has been completed.

This revised version contains material published in the two years since the original report was issued in January 1960. The report covers the history of the discovery of fission, fission theory, and the probability of fission. It discusses the distribution of mass in fission, the distribution of nuclear charge in fission, kinetic energy of fission fragments, and the role of neutrons and gamma rays in fission.

A capital cost breakdown of the Idaho Chemical Processing Plant, a directly maintained remotely operated plant for processing spent enriched uranium fuel assemblies from reactors, is presented. The capital investment in the plant, including design, construction, training, and preoperational costs, an estimate of the direct costs incurred by the Atomic Energy Commission, and a proportional part of the costs of Central Facilities, including the value of the land and improvements theorem when acquired by the Commision, was $31,105,899. The cost of design and construction was $25,212,231, of which $3,773,357 was expanded on design and inspection.

Abstract: Critical experiment studies were performed, varying the parameters U235, B10 and metal to water ratio, in the SM-2 7 x 7 core configuration with 38 stationary elements and seven control rods of the SM-1 (APPR-1) type. An experimental mock-up of the SM-1 was assembled using the basic SM-2 fuel plates. Excellent agreement between the SM-1 boron loading, determined by chemical analysis, and the SM-1 mock-up boron loading, for equivalent bank positions, was noted. Several SM-2 mock-ups, cold clean and midlife, were assembled and studied with regard to reflector effects, flow divider effects, relative control rod array worths, critical rod configurations, and relative power distributions. The results of these experiments indicate as satisfactory a U235 loading of 36.4 Kg and a B10 loading of 63.4 grams for the SM-2. Attention is drawn to numerous power peaks present in the active core. The open seven control rod array has a slight reactivity advantage over the closed seven array and consequent minor disadvantage with respect to "stuck rod" criteria.

Abstract: This preliminary technical report covers design of the SM Type 3 element, its use .in.. SM-1 Core III, and planned use in the Type 3 Core for PM-2A. The Type:3 element characteristics are compared with Type 1 (SM-1 Core I) element nuclear, metallurgical, thermal and hydraulic characteristics and fabrication. The effect of using the Type 3 element in SM-1 Core III and. its planned use in a Type 3 Core for PM-2A is discussed with regard to operation, shielding, reactor safety and all conceivable special problems.

Abstract: The results of activity buildup studies in the SM-1 performed during Core I lifetime (June 3, 1957 to April 28, 1960) are reported. Data are presented on the extent, nature, and mechanism of the buildup of long-lived gamma emitting nuclides in the reactor primary system. Radiation levels after reactor shutdown are presented, as well as mathematical equations used to account for the observed activity levels. The data have shown that Co60 is the major contributor to radiation levels in the SM-1. Co60 activity arises from the cobalt in Haynes 25 alloy flux suppressors, and the cobalt impurity in stainless steel. After 35 months operation at an average power level of 55%, deposited Co60 activity accounted for approximately 83% of the total radiation level (mr/hr) contributed by the long-lived gamma emitting nuclides. The contribution of the primary coolant activity to the total radiation level is insignificant when compared to the contribution of the activity deposited on the walls of the system. The radiation level on the super-heater side of the steam generator was about 1400 mr/hr after 35 months of reactor operation. The percentages of Co60 activity in the coolant and in the deposits were not the same. This indicates …

This report follows an investigation on Great Lakes Carbon with the objectives to demonstrate their ability to make and F process purify reactor carbon on a commercial scale; and construct an F process pilot plant and use it in a survey of U.S. petroleum cokes to discover additional supplies of raw coke suitable for making reactor grade carbon.

This report contains a recapitulation of activity in the SM-2 Core and Vessel Program during the period December 15, 1959 to March 18, 1960.

The purpose of the test was to obtain performance data for the main coolant pumps on fast and slow speed at various coolant temperatures. The 1A, 1B and 1C pump performances on both fast and slow speed were approximately as shown in the manufacture's predicted performance curve. The 1D pump performance was below the manufacturer's predicted flow efficiency, line current and hydraulic horsepower on both fast and slow speeds.

From introduction: "The ORNL-ANP liquid-to-liquid heat exchanger design and development effort has been based on an exceptionally high performance matrix of closely-spaced small diameter tubes that permits practically pure counter-flow operation. In the course of full-scale aircraft power plant design work a number of charts for this type of heat exchanger has been prepared. These charts were intended in part to show the effects of the various parameters in a readily understandable form, and in part to simplify and to reduce markedly the chore of making detailed design calculations. These charts have proved so helpful it seemed very worthwhile to assemble them into a report along with brief explanations and sample calculations."