"A flight investigation of a 1/7-scale rocket-powered model of the XF10F Grumman XF10F airplane in the swept-wing configuration has been made. The purpose of this test was to determine the static longitudinal stability, damping in pitch, and longitudinal control effectiveness of the airplane with the center of gravity at 20 percent of the wing mean aerodynamic chord. Only a small amount of data was obtained from the test because, immediately after booster separation at a Mach number of 0.88, the configuration was directionally unstable and diverged in sideslip" (p. 1).

"A flight test was made to determine the servoplane effectiveness and stability characteristics of the free-floating horizontal stabilizer to be used on the XF10F airplane. The results of this test indicate that servoplane effectiveness is practically constant through the speed range up to a Mach number of 1.15, and the stabilizer static stability is satisfactory. A loss of damping occurs over a narrow Mach number range near M = 1.0, resulting in dynamic instability of the stabilizer in this narrow range" (p. 1).

"The rocket-propelled-model technique has been applied to the investigation of low-lift buffeting. Results of preliminary tests show that severe buffeting, wing dropping, and normal-force changes occur almost simultaneously near zero lift over a Mach number range near 0.9 on unswept wings 12 percent thick. On unswept wings 7 percent thick, buffeting did not occur; however, mild wing dropping and normal-force changes were experienced" (p. 1).

Report presenting some equations that give the interference on the trailing-vortex system of a uniformly loaded finite-span wing in a circular tunnel containing partly open and partly closed walls, with special reference to symmetrical arrangements of the open and closed portions. Methods are given for extending the equations to include tunnel shapes other than circular.

Report presenting drag coefficients during power-off transonic flight for the Bell X-1 airplane with a 10-percent-thick wing over a range of Mach numbers and pressure altitudes. The data was compared to an X-1 with an 8-percent-thick wing and a wind tunnel test with a 10-percent-thick wing. Information about necessary angle of attack, drag-rise Mach number, maximum lift-drag ratio, and drag coefficient at zero lift is provided.

From Introduction: "The general objective of this report is a study of the characteristics of the described form of peak holding control. The control has not yet been used in experimental turbojet-engine study.This study is concerned with only one method of extracting the maximum amount of information from a peak output for the purpose of maintaining that peak. The criteria sought in this control process are: maintenance of peak average output, minimum duration of time in undesirable operation, quickness in response to command to reach peak condition, least amount of excursion in the undesirable region, and type of stability."

Memorandum presenting an investigation of the effects of compressibility on the forces, pitching moments, and surface pressures on a wing-nacelle combination. The leading edge of the wing was swept back 37.25 degrees and the nacelle was a body of revolution with a fineness ratio of 6.5. The effects of compressibility on the surface pressures and on the drag of a body of revolution similar to the nacelle were also determined.

"An investigation has been made at high subsonic speeds of the aerodynamic characteristics in pitch and sideslip of a 1/l4-scale model of the Grumman XF10F airplane with a wing sweepback angle of 42.5. The longitudinal stability characteristics (with the horizontal tail fixed) indicate a pitch-up near the stall; however, this was somewhat alleviated by the addition of fins to the side of the fuselage below the horizontal tail. The original model configuration became directionally unstable for small sideslip angles at Mach numbers above 0.8; however, the instability was eliminated by several different modifications" (p. 1).

Memorandum presenting a method for calculating the stick-fixed longitudinal stability of a wing-fuselage configuration at subcritical Mach numbers. The method applies to unswept- and swept-wing configurations. The stability parameters estimated by the method show reasonable agreement with the experimental values for the 23 configurations used in the comparison.

Memorandum presenting an investigation made of the effects of store mounting on the buffet, trim, and drag characteristics of fuselage-mounted external stores between Mach numbers of 0.7 and 1.4 by the use of the rocket-propelled-model technique. Results of the tests are presented in the incremental accelerations in the stores due to buffeting, trim normal- and side-force coefficients, tail helix angles, and drag coefficients plotted against Mach number.

Report presenting the results of a limited research program initiated to study the effects of a hot propulsive jet on the longitudinal stability characteristics of a fighter-type airplane configuration. The data was obtained from a rocket-boosted free-flight model investigation over a range of Mach numbers using four models that differed only in the position and size of the horizontal tail. Results regarding the time histories, trim, normal force, pitching moment, aerodynamic-center location, dynamic stability, trim drag, and pressure data are provided.

Memorandum listing NACA reports related to a variety of research topics, including instruments, research equipment, and research techniques.

Report presenting an investigation of the effects of adding leading-edge roughness to the surfaces of an unswept, untapered, 6-percent-thick, circular-arc-airfoil wing equipped with a full-span, 0.2-chord, plain, trailing-edge aileron. Results regarding the rolling-effectiveness data, addition of roughness on a wing, and variation of drag coefficient are provided.

From Summary: "The aeroelastic effects on wing-aileron rolling effectiveness and drag of thin flat-plate delta wings with 45 degree swept leading edge and plain constant-chord ailerons have been investigated. This investigation has been carried out over a Mach number range of 0.7 to 1.6 by means of rocket-propelled test vehicles in free flight. The results show a near-linear decrease in lateral control effectiveness with a decrease in the wing torsional stiffness. An aileron-effectiveness reversal was experienced with the more flexible delta-wing models."

Report discussing an investigation to determine the effects of aeroelasticity on the rolling effectiveness of a model of a McDonnell F3H-1 airplane wing. The plane was found to be subject to aeroelastic losses that varied with Mach number and altitude.

Report presenting an investigation to determine the effects of aeroelasticity on the rolling effectiveness of an 8.06-percent-scale model of the McDonnell F3H-1 airplane wing. The investigation used rocket-propelled models in free flight over a range of Mach numbers. The results indicate that the airplane is subject to aeroelastic losses varying from about 7 percent at Mach number 0.5 to 46 percent at Mach number 0.90 at sea level.

Report presenting testing of two rocket-propelled research models to determine the effect of the intersection of thin aerodynamic surfaces and the effect of moderate sweepback of thick aerodynamic surfaces on low-lift buffeting. Results regarding trim changes and drag are also provided. It was discovered that low-lift buffeting may be induced at high subsonic speeds by interference due to the intersection of thin aerodynamic surfaces.

Memorandum presenting a two-dimensional wind-tunnel investigation of the effects of maximum-thickness location on fluctuating pressures and normal-force coefficients on 9-percent-thick airfoils, which indicated that for normal-force coefficients up to 0.6, the section variables had little effect on the pressure pulsations and root-mean-square normal-force-coefficient fluctuations. Results regarding pressure fluctuations and normal-force-coefficient fluctuations are provided.

Report presenting a flight investigation of four air-to-air missiles mounted by pylons on a rocket-powered basic wingless buffet-research vehicle to determine the trim, buffet, and drag characteristics of the combination.

"Approximately 2,000 flights of rocket-propelled models have been made in which model configuration, model size, type and number of booster rockets, number of booster stages, and booster arrangements varied. A brief summary of the results obtained with some of the more unusual arrangements, descriptions of boosting hardware and techniques, and discussions of some factors responsible for the choice of these configurations are presented in this paper. The results show that unconventional boosting techniques may be used successfully when conventional tandem arrangements are unsuitable or unwieldy" (p. 1).

Report presenting an investigation of the intensity of root-mean-square pressure pulsations and root-mean-square normal-force-coefficient fluctuations conducted on two high-lift airfoils and two 6-series airfoils. Results regarding the factors affecting comparison of data from various test facilities, root-mean-square pressure pulsations, and root-mean-square force fluctuations are provided.

Report presenting a flight and preflight evaluation of an automatic thrust-coefficient control system in a twin-engine ram-jet missile. A flicker-type single-loop servocontrol system is shown to be a usable way of controlling ram-jet thrust coefficients.

Report discussing an investigation into the effects of camber and leading-edge-flap deflection on the pressure pulsations on thin rigid airfoils at a range of Mach numbers. The ideal camber or flap deflection was found to be dependent on Mach number and normal-force coefficient. The results of this testing, which used a 64A006 airfoil, was compared to previous testing using a 65A006 airfoil.

Report presenting information about airfoil section normal-force, drag, pitching-moment, flap-normal-force, and hinge-moment characteristics at Mach numbers from 0.5 to 1.0 on an NACA 64A006 airfoil with 15-percent-chord leading-edge flap. Differing results were noted in the Mach ranges of 0.5 to 0.8 and over 0.8.