Technology developed by the late Dr. Felix Sebba of the VPI Chemical Engineering Department by which an oil phase can be broken up into small droplets and encapsulated in a continuous water phase led to research on the possible merits of a fuel prepared by this procedure. The resulting mixture is called a polyaphron. Part 1 of this report describes the testing of polyaphronated gasoline in an automobile engine. Nitrogen oxides (NO{sub x}) emissions, total hydrocarbon (HC) emissions, and exhaust temperature were determined for various load and RPM combinations. Difficulties with viscosity and separation of the water phase have prevented complete testing at road load conditions. Rather than continue with engine testing, some bench tests of polyaphrons were performed to see the effect of various filtering processes on fuel stability as well as measuring viscosity and density. These results are reported in Part 2 of this paper. 6 figs., 4 tabs.

This Technical Progress Report describes progress made on the seventeen subprojects awarded in the first year of Cooperative Agreement DE-FC26-02NT41607: Crosscutting Technology Development at the Center for Advanced Separation Technologies. This work is summarized in the body of the main report: the individual sub-project Technical Progress Reports are attached as Appendices. Due to the time taken up by the solicitation/selection process, these cover the initial 6-month period of project activity only. The U.S. is the largest producer of mining products in the world. In 1999, U.S. mining operations produced $66.7 billion worth of raw materials that contributed a total of $533 billion to the nation's wealth. Despite these contributions, the mining industry has not been well supported with research and development funds as compared to mining industries in other countries. To overcome this problem, the Center for Advanced Separation Technologies (CAST) was established to develop technologies that can be used by the U.S. mining industry to create new products, reduce production costs, and meet environmental regulations. Originally set up by Virginia Tech and West Virginia University, this endeavor has been expanded into a seven-university consortium--Virginia Tech, West Virginia University, University of Kentucky, University of Utah, Montana Tech, New Mexico Tech …

The basic characteristics of a self-sustaining chain reaction were demonstrated with the Chicago Pile in 1943, but it was not until early 1945 that sufficient enriched material became available to experimentally verify fast-neutron cross-sections and the kinetic characteristics of a nuclear chain reaction sustained with prompt neutrons alone. However, the demands of wartime and the rapid decline in effort following the cessation of hostilities often resulted in the failure to fully document the experiments or in the loss of documentation as personnel returned to civilian pursuits. When documented, the results were often highly classified. Even when eventually declassified, the data were often not approved for public release until years later.2 Even after declassification and approval for public release, the records are sometimes difficult to find. Through a fortuitous discovery, a set of handwritten notes by ''ORF July 1945'' entitled ''Dragon - Research with a Pulsed Fission Reactor'' was found by William L. Myers in an old storage safe at Pajarito Site of the Los Alamos National Laboratory3. Of course, ORF was identified as Otto R. Frisch. The document was attached to a page in a nondescript spiral bound notebook labeled ''494 Book'' that bore the signatures of Louis Slotin and …

The Department of Energy (DOE) awarded a contract entitled Engineering Development of Advanced Physical Fine Coal Cleaning Technology - Froth Flotation'', to ICF Kaiser Engineers with the following team members, Ohio Coal Development Office, Babcock and Wilcox, Consolidation Coal Company, Eimco Process Equipment Company, Illinois State Geological Survey, Virginia Polytechnic Institute and State University, Process Technology, Inc. This document a quarterly report prepared in accordance with the project reporting requirements covering the period from July 1, 1992 to September 30, 1992. This report provides a summary of the technical work undertaken during this period, highlighting the major results. A brief description of the work done prior to this quarter is provided in this report under the task headings.

Work completed produced the criteria for additional engineering analysis, computation and detailed experimental benchscale testing for areas of uncertainty. The engineering analysis, computation, bench-scale testing and component development was formulated to produce necessary design information to define a commercially operating system. In order to produce the required information by means of bench-scale testing and component development, a uniform coal sample was procured. After agreement with DOE, a selected sample of coal from those previously listed was secured. The test plan was developed in two parts. The first part listed procedures for engineering and computational analyses of those deficiencies previously identified that could be solved without bench scale testing. Likewise, the second part prepared procedures for bench-scale testing and component development for those deficiencies previously identified in Task 3.

The Department of Energy (DOE) awarded a contract entitled ``Engineering Development of Advanced Physical Fine Coal Cleaning Technology - Froth Flotation``, to ICF Kaiser Engineers with the following team members, Ohio Coal Development Office, Babcock and Wilcox, Consolidation Coal Company, Eimco Process Equipment Company, Illinois State Geological Survey, Virginia Polytechnic Institute and State University, Process Technology, Inc. This document a quarterly report prepared in accordance with the project reporting requirements covering the period from July 1, 1992 to September 30, 1992. This report provides a summary of the technical work undertaken during this period, highlighting the major results. A brief description of the work done prior to this quarter is provided in this report under the task headings.

Work completed produced the criteria for additional engineering analysis, computation and detailed experimental benchscale testing for areas of uncertainty. The engineering analysis, computation, bench-scale testing and component development was formulated to produce necessary design information to define a commercially operating system. In order to produce the required information by means of bench-scale testing and component development, a uniform coal sample was procured. After agreement with DOE, a selected sample of coal from those previously listed was secured. The test plan was developed in two parts. The first part listed procedures for engineering and computational analyses of those deficiencies previously identified that could be solved without bench scale testing. Likewise, the second part prepared procedures for bench-scale testing and component development for those deficiencies previously identified in Task 3.

Clouds in the tropical western Pacific are an integral part of the large scale environment. An improved understanding of the multi-scale structure of clouds and their interactions with the environment is critical to the ARM (Atmospheric Radiation Measurement) program for developing and evaluating cloud parameterizations, understanding the consequences of model biases, and providing a context for interpreting the observational data collected over the ARM Tropical Western Pacific (TWP) sites. Three-dimensional cloud resolving models (CRMs) are powerful tools for developing and evaluating cloud parameterizations. However, a significant challenge in using CRMs in the TWP is that the region lacks conventional data, so large uncertainty exists in defining the large-scale environment for clouds. This project links several aspects of the ARM program, from measurements to providing improved analyses, and from cloud-resolving modeling to climate-scale modeling and parameterization development, with the overall objective to improve the representations of clouds in climate models and to simulate and quantify resolved cloud effects on the large-scale environment. Our objectives will be achieved through a series of tasks focusing on the use of the Weather Research and Forecasting (WRF) model and ARM data. Our approach includes: -- Perform assimilation of COSMIC GPS radio occultation and other satellites …

As a generator of transuranic (TRU) and TRU mixed waste destined for disposal at the Waste Isolation Pilot Plant (WIPP), the Hanford Site must ensure that its TRU waste meets the requirements of U.S. Department of Energy (DOE) Order 5820.2A, ''Radioactive Waste Management, and the Waste Acceptance Criteria for the Waste Isolation Pilot Plant' (DOE 1996d) (WIPP WAC). The WIPP WAC establishes the specific physical, chemical, radiological, and packaging criteria for acceptance of defense TRU waste shipments at WIPP. The WIPP WAC also requires that participating DOE TRU waste generator/treatment/storage sites produce site-specific documents, including a certification plan, that describe their management of TRU waste and TRU waste shipments before transferring waste to WIPP. The Hanford Site must also ensure that its TRU waste destined for disposal at WIPP meets requirements for transport in the Transuranic Package Transporter41 (TRUPACT-11). The U.S. Nuclear Regulatory Commission (NRC) establishes the TRUPACT-I1 requirements in the ''Safety Analysis Report for the TRUPACT-II Shipping Package'' (NRC 1997) (TRUPACT-I1 SARP).

None

U.S. Department of Energy (DOE) Order 450.1, Environmental Protection Program, requires each DOE site to conduct environmental monitoring. Environmental monitoring at the Waste Isolation Pilot Plant (WIPP) is conducted in order to: (a) Verify and support compliance with applicable federal, state, and local environmental laws, regulations, permits, and orders; (b) Establish baselines and characterize trends in the physical, chemical, and biological condition of effluent and environmental media; (c) Identify potential environmental problems and evaluate the need for remedial actions or measures to mitigate the problems; (d) Detect, characterize, and report unplanned releases; (e) Evaluate the effectiveness of effluent treatment and control, and pollution abatement programs; and (f) Determine compliance with commitments made in environmental impact statements, environmental assessments, safety analysis reports, or other official DOE documents. This Environmental Monitoring Plan (EMP) explains the rationale and design criteria for the environmental monitoring program, extent and frequency of monitoring and measurements, procedures for laboratory analyses, quality assurance (QA) requirements, program implementation procedures, and direction for the preparation and disposition of reports. Changes to the environmental monitoring program may be necessary to allow the use of advanced technology and new data collection techniques. This EMP will document changes in the environmental monitoring program. …

This project contributed significantly to the development of new codes and standards, both domestically and internationally. The NHA collaborated with codes and standards development organizations to identify technical areas of expertise that would be required to produce the codes and standards that industry and DOE felt were required to facilitate commercialization of hydrogen and fuel cell technologies and infrastructure. NHA staff participated directly in technical committees and working groups where issues could be discussed with the appropriate industry groups. In other cases, the NHA recommended specific industry experts to serve on technical committees and working groups where the need for this specific industry expertise would be on-going, and where this approach was likely to contribute to timely completion of the effort. The project also facilitated dialog between codes and standards development organizations, hydrogen and fuel cell experts, the government and national labs, researchers, code officials, industry associations, as well as the public regarding the timeframes for needed codes and standards, industry consensus on technical issues, procedures for implementing changes, and general principles of hydrogen safety. The project facilitated hands-on learning, as participants in several NHA workshops and technical meetings were able to experience hydrogen vehicles, witness hydrogen refueling demonstrations, see …

DNA damage in mammalian chromatin in vitro and in cultured mammalian cells including human cells was studied. In the first phase of these studies, a cell culture laboratory was established. Necessary equipment including an incubator, a sterile laminar flow hood and several centrifuges was purchased. We have successfully grown several cell lines such as murine hybridoma cells, V79 cells and human K562 leukemia cells. This was followed by the establishment of a methodology for the isolation of chromatin from cells. This was a very important step, because a routine and successful isolation of chromatin was a prerequisite for the success of the further studies in this project, the aim of which was the measurement of DNA darnage in mammalian chromatin in vitro and in cultured cells. Chromatin isolation was accomplished using a slightly modified procedure of the one described by Mee & Adelstein (1981). For identification and quantitation of DNA damage in cells, analysis of chromatin was preferred over the analysis of "naked DNA" for the following reasons: i. DNA may not be extracted efficiently from nucleoprotein in exposed cells, due to formation of DNA-protein cross-links, ii. the extractability of DNA is well known to decrease with increasing doses of …

Four new Resource Conservation and Recovery Act (RCRA) groundwater monitoring wells were installed at the single-shell tank farm Waste Management Area (WMA) C in fiscal year 2003 to fulfill commitments for well installations proposed in the draft Hanford Federal Facility Agreement and Consent Order milestone M-24-00. Well 299-E27-22, installed upgradient, was drilled through the entire uppermost unconfined aquifer to the basalt and wells 299-E27-4, 299-E27-21 and 299-E27-23 were drilled approximately 40 feet into the uppermost unconfined aquifer and installed downgradient of the WMA. Specific objectives for these wells include monitoring the impact, if any, that potential releases from inside the WMA may have on current groundwater conditions (i.e., improved network coverage) and differentiating upgradient groundwater contamination from contaminants released at the WMA. This report supplies the information obtained during drilling, characterization, and installation of the four new groundwater monitoring wells. This document also provides a compilation of hydrogeologic and well construction information obtained during drilling, well development, aquifer testing, and sample collection/analysis activities.

Under provisions of the Surplus Facilities Management Program (SFMP), the US Department of Energy, Chicago Operations Office, proposes to provide funding for Surveillance and Maintenance (S & M) and subsequent Decontamination and Decommissioning (D & D) of fifteen facilities and associated premises belonging to Battelle Columbus Division. The fifteen facilities are contaminated as a result of nuclear research and development activities conducted over a period of approximately 43 years for DOE and its predecessor agencies--the Energy Research and Development Administration (ERDA), the Atomic Energy Commission (AEC) and the Manhattan Engineer District (MED). The proposed action includes continuation of ongoing S & M as well as a D & D of the facilities. The S & M activities include a continued environmental monitoring program to maintain assurance that radioactive contamination has not escaped to the surrounding environment; regularly scheduled inspection and maintenance of health, safety, and radiation protection equipment and instrumentation; a program of health physics surveillance monitoring, personnel dosimetry, and equipment and instrumentation maintenance and calibration; and emergency planning, training, and drills. The so- called dismantlement D & D mode is the proposed alternative for D & D of these facilities. For the facilities in question this will generally involve …

The majority of scientific software is distributed as source code. As the number of library dependencies and supported platforms increases, so does the complexity of describing the rules for configuring and building software. In this project, we have performed an empirical study of the magnitude of the build problem by examining the development history of two DOE-funded scientific software projects. We have developed MixDown, a meta-build tool, to simplify the task of building applications that depend on multiple third-party libraries. The results of this research indicate that the effort that scientific programmers spend takes a significant fraction of the total development effort and that the use of MixDown can significantly simplify the task of building software with multiple dependencies.

This document is an addendum to the Corrective Action Decision Document (CADD) that has been prepared for Corrective Action Unit (CAU) 254, Area 25 Reactor Maintenance, Assembly, and Disassembly (R-MAD) Decontamination Facility. CAU 254 consists of Corrective Action Site (CAS) 25-23-06, Decontamination Facility. The purpose of this addendum is to provide a rationale for the recommendation of a revised preferred alternative corrective action for CAU 254. This preferred alternative corrective action, Alternative 3, consists of the removal of accessible soil/sediment and all building material above ground level from the CAU 254 Site. This alternative is being recommended because a cost-effective technology is now available to dismantle the contaminated building and ensure complete removal of all CAU 254 CADD-identified contaminants of concern and any associated contamination. This preferred closure method alternative reduces the potential for future exposure pathways. Procedures will be developed, presented in the Corrective Action Plan, and implemented to ensure worker health and safety, protection of human health and the environment, and to meet all unrestricted release requirements in accordance with applicable state and federal regulations.

The purpose of this analysis is to evaluate impacts to the retrieval concept presented in the Design Analysis ''Retrieval Equipment and Strategy'' (Reference 6), from abnormal events based on Design Basis Events (DBE) and Beyond Design Basis Events (BDBE) as defined in two recent analyses: (1) DBE/Scenario Analysis for Preclosure Repository Subsurface Facilities (Reference 4); and (2) Preliminary Preclosure Design Basis Event Calculations for the Monitored Geologic Repository (Reference 5) The objective of this task is to determine what impacts the DBEs and BDBEs have on the equipment developed for retrieval. The analysis lists potential impacts and recommends changes to be analyzed in subsequent design analyses for developed equipment, or recommend where additional equipment may be needed, to allow retrieval to be performed in all DBE or BDBE situations. This analysis supports License Application design and therefore complies with the requirements of Systems Description Document input criteria comparison as presented in Section 7, Conclusions. In addition, the analysis discusses the impacts associated with not using concrete inverts in the emplacement drifts. The ''Retrieval Equipment and Strategy'' analysis was based on a concrete invert configuration in the emplacement drift. The scope of the analysis, as presented in ''Development Plan for Retrieval …

The VAM3D-CG computer code has been licensed for use at Hanford, from HydroGeologic, Inc., of Herndon, VA. Version 2.4b has been installed on the 3200GWW workstations, and is currently under configuration management. The purpose of this report is to describe the installation and configuration management of VAM3D-CG on the Hanford Computer System. VAM3D-CG is written in standard FORTRAN F77.

The burns to the skin of anesthetized rats were determined for the thermal radiation pulses of a carbon arc on a hot-wet uniform when spaced 5 mm from the skin. The radiant exposures to cause burns resulting in eschar were tion pulses corresponding to 250, 1000, 2900, and 10,000 kiloton detonations, respectively. The threshold lesions were caused by volatile products not associated with ignition. The associated temperatures were recorded. (auth)

Results are reviewed from a number of studies on the biological effects of static and low frequency electromagnetic fields on animals. Based on a long history of experience with electric fields by the utility industry, it appears that intermittent and repeated exposures to strong 60-Hz electromagnetic fields from present power transmission systems have no obvious adverse effect on the health of man. It has been recognized recently that this belief must be tested by carefully designed and executed experiments under laboratory conditions where precise control can be exercised over coexisting environmental factors. A number of studies have been initiated in response to this need to evaluate possible effects from both acute and chronic exposures. 100 references.

The purpose of this report is to describe the methodology and results obtained from a continuing DOE Office of Transportation Technologies (OTT) activity to estimate future effects of OTT projects on national energy use, petroleum consumption, criteria emissions, greenhouse gas emissions, and various measures of national income and employment. Assumptions are made about the future costs and characteristics of alternative vehicles and fuels. Models that take into account the value that vehicle buyers place on various vehicle characteristics are used to estimate the market penetration of new vehicle technologies. A different set of assumptions would yield results that are different from what is presented here. Analysis results quantify various benefits including: energy and petroleum reductions, carbon equivalent greenhouse gas emissions, criteria pollutant emissions reductions, and the associated economic impacts on the Gross Domestic Product (GDP) and jobs. The scope of this report addresses light vehicles including passenger automobiles, Class 1 and 2 trucks, and heavy trucks (Classes 3 through 8). The time period spans the present through the year 2030. All energy savings start from baseline projections of transportation sector energy use obtained from the ''Annual Energy Outlook,'' issued annually by the US Department of Energy, Energy Information Administration (Ref. …

By reviewing how microorganisms interact with actinides in subsurface environments, we assess how bioremediation controls the fate of actinides. Actinides often are co-contaminants with strong organic chelators, chlorinated solvents, and fuel hydrocarbons. Bioremediation can immobilize the actinides, biodegrade the co-contaminants, or both. Actinides at the IV oxidation state are the least soluble, and microorganisms accelerate precipitation by altering the actinide's oxidation state or its speciation. We describe how microorganisms directly oxidize or reduce actinides and how microbiological reactions that biodegrade strong organic chelators, alter the pH, and consume or produce precipitating anions strongly affect actinide speciation and, therefore, mobility. We explain why inhibition caused by chemical or radiolytic toxicities uniquely affects microbial reactions. Due to the complex interactions of the microbiological and chemical phenomena, mathematical modeling is an essential tool for research on and application of bioremediation involving co-contamination with actinides. We describe the development of mathematical models that link microbiological and geochemical reactions. Throughout, we identify the key research needs.

The Corrective Action Investigation Plan for Corrective Action Unit 263, the Area 25 Building 4839 Leachfield, has been developed in accordance with the Federal Facility Agreement and Consent Order that was agreed to by the US Department of Energy, Nevada Operations Office; the Nevada Division of Environmental Protection; and the US Department of Defense. Corrective Action Unit 263 is comprised of the Corrective Action Site 25-05-04 sanitary leachfield and associated collection system. This Corrective Action Investigation Plan is used in combination with the Work Plan for Leachfield Corrective Action Units: Nevada Test Site and Tonopah Test Range, Nevada (DOE/NV, 1998d). The Leachfield Work Plan was developed to streamline investigations at Leachfield Corrective Action Units by incorporating management, technical, quality assurance, health and safety, public involvement, field sampling, and waste management information common to a set of Corrective Action Units with similar site histories and characteristics into a single document that can be referenced. This Corrective Action Investigation Plan provides investigative details specific to Corrective Action Unit 263. Corrective Action Unit 263 is located southwest of Building 4839, in the Central Propellant Storage Area. Operations in Building 4839 from 1968 to 1996 resulted in effluent releases to the leachfield and associated …